[PATCH v2 07/13] drm/meson: Add support for HDMI encoder and DW-HDMI bridge + PHY

[Neil Armstrong]

On 04/04/2017 10:57 AM, Daniel Vetter wrote:
> On Tue, Mar 21, 2017 at 04:25:44PM +0100, Neil Armstrong wrote:
>> The Amlogic Meson GXBB/GXL/GXM SoCs embeds a Synopsys DesignWare HDMI TX
>> Controller with a custom Bridge + PHY around the Controller.
>>
>> This driver makes uses of all the custom PHY plat data callbacks and enables
>> the compatible HDMI modes to be configured as a drm_encoder instance.
>>
>> Signed-off-by: Neil Armstrong <narmstrong at baylibre.com>
> 
> [snip]
> 
>> +static int meson_venc_hdmi_encoder_atomic_check(struct drm_encoder *encoder,
>> +					struct drm_crtc_state *crtc_state,
>> +					struct drm_connector_state *conn_state)
>> +{
>> +	return 0;
>> +}
> 
> Given the over-the-top complicated mode encoding you seem to have, this
> feels like it's a bit too simply.

Indeed, but the HW is really weird, every supported modes have very specific
timings/parameters so moving the mode validation code from the dw-hdmi mode_valid
to here would only make sense if we need to support a different HDMI controller.

But you are right, but I would have preferred to have a better HW for sure...

> 
>> +
>> +static void meson_venc_hdmi_encoder_disable(struct drm_encoder *encoder)
>> +{
>> +	struct meson_dw_hdmi *dw_hdmi = encoder_to_meson_dw_hdmi(encoder);
>> +	struct meson_drm *priv = dw_hdmi->priv;
>> +
>> +	DRM_DEBUG_DRIVER("\n");
>> +
>> +	writel_bits_relaxed(0x3, 0,
>> +			    priv->io_base + _REG(VPU_HDMI_SETTING));
>> +
>> +	writel_relaxed(0, priv->io_base + _REG(ENCI_VIDEO_EN));
>> +	writel_relaxed(0, priv->io_base + _REG(ENCP_VIDEO_EN));
>> +}
>> +
>> +static void meson_venc_hdmi_encoder_enable(struct drm_encoder *encoder)
>> +{
>> +	struct meson_dw_hdmi *dw_hdmi = encoder_to_meson_dw_hdmi(encoder);
>> +	struct meson_drm *priv = dw_hdmi->priv;
>> +
>> +	DRM_DEBUG_DRIVER("%s\n", priv->venc.hdmi_use_enci ? "VENCI" : "VENCP");
>> +
>> +	if (priv->venc.hdmi_use_enci)
>> +		writel_relaxed(1, priv->io_base + _REG(ENCI_VIDEO_EN));
>> +	else
>> +		writel_relaxed(1, priv->io_base + _REG(ENCP_VIDEO_EN));
>> +}
>> +
>> +static void meson_venc_hdmi_encoder_mode_set(struct drm_encoder *encoder,
>> +				   struct drm_display_mode *mode,
>> +				   struct drm_display_mode *adjusted_mode)
>> +{
>> +	struct meson_dw_hdmi *dw_hdmi = encoder_to_meson_dw_hdmi(encoder);
>> +	struct meson_drm *priv = dw_hdmi->priv;
>> +	int vic = drm_match_cea_mode(mode);
>> +
>> +	DRM_DEBUG_DRIVER("%d:\"%s\" vic %d\n",
>> +			 mode->base.id, mode->name, vic);
>> +
>> +	/* Should have been filtered */
>> +	if (!vic)
>> +		return;
>> +
>> +	/* VENC + VENC-DVI Mode setup */
>> +	meson_venc_hdmi_mode_set(priv, vic, mode);
> 
> So this calls a different module which export_symbol_gpls that thing. I
> have no idea why arm-soc people love modularized-to-the-function level
> drivers, but it feels over the top. amd/nouveau/i915 all smash everything
> into one driver, makes life so much easier.

I know, we are doomed on that !
But here, since the wrapping around the dw-hdmi controller is completely custom
if was necessary to add a separate encoder tied to HDMI and have the physical
encoding code in the common driver.
Note that the platform is also able to driver a LCD via LVDS, so this encoder code
should be reusable here.

> 
> Note: bridge drivers as separate .ko makes sense, but separate .ko for
> every single functional unit in your vendor IP imo totally doesn't.

Actually I added a global ko for the "DRM" driver with crtc, planes and CVBS,
and another ko for the HDMI bridge wrapping.

> 
> Not going to stop you either :-)

I totally agree on the complexity here !

> -Daniel
>