[PATCH V5 3/4] drm/bridge: Add driver for GE B850v3 LVDS/DP++ Bridge
Archit Taneja
architt at codeaurora.org
Mon Sep 26 03:29:06 PDT 2016
Hi,
Some comments.
On 08/09/2016 10:11 PM, Peter Senna Tschudin wrote:
> Add a driver that create a drm_bridge and a drm_connector for the LVDS
> to DP++ display bridge of the GE B850v3.
>
> There are two physical bridges on the video signal pipeline: a
> STDP4028(LVDS to DP) and a STDP2690(DP to DP++). The hardware and
> firmware made it complicated for this binding to comprise two device
> tree nodes, as the design goal is to configure both bridges based on
> the LVDS signal, which leave the driver powerless to control the video
> processing pipeline. The two bridges behaves as a single bridge, and
> the driver is only needed for telling the host about EDID / HPD, and
> for giving the host powers to ack interrupts. The video signal pipeline
> is as follows:
>
> Host -> LVDS|--(STDP4028)--|DP -> DP|--(STDP2690)--|DP++ -> Video output
>
> Cc: Martyn Welch <martyn.welch at collabora.co.uk>
> Cc: Martin Donnelly <martin.donnelly at ge.com>
> Cc: Daniel Vetter <daniel.vetter at ffwll.ch>
> Cc: Enric Balletbo i Serra <enric.balletbo at collabora.com>
> Cc: Philipp Zabel <p.zabel at pengutronix.de>
> Cc: Rob Herring <robh at kernel.org>
> Cc: Fabio Estevam <fabio.estevam at nxp.com>
> CC: David Airlie <airlied at linux.ie>
> CC: Thierry Reding <treding at nvidia.com>
> CC: Thierry Reding <thierry.reding at gmail.com>
> Reviewed-by: Enric Balletbo <enric.balletbo at collabora.com>
> Signed-off-by: Peter Senna Tschudin <peter.senna at collabora.com>
> ---
> Changes from V4:
> - Check the output of the first call to i2c_smbus_write_word_data() and return
> it's error code for failing gracefully on i2c issues
> - Renamed the i2c_driver.name from "ge,b850v3-lvds-dp" to "b850v3-lvds-dp" to
> remove the comma from the driver name
>
> Changes from V3:
> - 3/4 instead of 4/5
> - Tested on next-20160804
>
> Changes from V2:
> - Made it atomic to be applied on next-20160729 on top of Liu Ying changes
> that made imx-ldb atomic
>
> Changes from V1:
> - New commit message
> - Removed 3 empty entry points
> - Removed memory leak from ge_b850v3_lvds_dp_get_modes()
> - Added a lock for mode setting
> - Removed a few blank lines
> - Changed the order at Makefile and Kconfig
>
> MAINTAINERS | 8 +
> drivers/gpu/drm/bridge/Kconfig | 11 +
> drivers/gpu/drm/bridge/Makefile | 1 +
> drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c | 405 +++++++++++++++++++++++++++++
> 4 files changed, 425 insertions(+)
> create mode 100644 drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index a306795..e8d106a 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -5142,6 +5142,14 @@ W: https://linuxtv.org
> S: Maintained
> F: drivers/media/radio/radio-gemtek*
>
> +GENERAL ELECTRIC B850V3 LVDS/DP++ BRIDGE
> +M: Peter Senna Tschudin <peter.senna at collabora.com>
> +M: Martin Donnelly <martin.donnelly at ge.com>
> +M: Martyn Welch <martyn.welch at collabora.co.uk>
> +S: Maintained
> +F: drivers/gpu/drm/bridge/ge_b850v3_dp2.c
> +F: Documentation/devicetree/bindings/ge/b850v3_dp2_bridge.txt
> +
> GENERIC GPIO I2C DRIVER
> M: Haavard Skinnemoen <hskinnemoen at gmail.com>
> S: Supported
Could you move the MAINTAINERS change to a different patch? It would
make it easier to integrate separately.
> diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
> index b590e67..b4b70fb 100644
> --- a/drivers/gpu/drm/bridge/Kconfig
> +++ b/drivers/gpu/drm/bridge/Kconfig
> @@ -32,6 +32,17 @@ config DRM_DW_HDMI_AHB_AUDIO
> Designware HDMI block. This is used in conjunction with
> the i.MX6 HDMI driver.
>
> +config DRM_GE_B850V3_LVDS_DP
> + tristate "GE B850v3 LVDS to DP++ display bridge"
> + depends on OF
> + select DRM_KMS_HELPER
> + select DRM_PANEL
> + ---help---
> + This is a driver for the display bridge of
> + GE B850v3 that convert dual channel LVDS
> + to DP++. This is used with the i.MX6 imx-ldb
> + driver.
> +
> config DRM_NXP_PTN3460
> tristate "NXP PTN3460 DP/LVDS bridge"
> depends on OF
> diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
> index efdb07e..b9606f3 100644
> --- a/drivers/gpu/drm/bridge/Makefile
> +++ b/drivers/gpu/drm/bridge/Makefile
> @@ -3,6 +3,7 @@ ccflags-y := -Iinclude/drm
> obj-$(CONFIG_DRM_ANALOGIX_ANX78XX) += analogix-anx78xx.o
> obj-$(CONFIG_DRM_DW_HDMI) += dw-hdmi.o
> obj-$(CONFIG_DRM_DW_HDMI_AHB_AUDIO) += dw-hdmi-ahb-audio.o
> +obj-$(CONFIG_DRM_GE_B850V3_LVDS_DP) += ge_b850v3_lvds_dp.o
> obj-$(CONFIG_DRM_NXP_PTN3460) += nxp-ptn3460.o
> obj-$(CONFIG_DRM_PARADE_PS8622) += parade-ps8622.o
> obj-$(CONFIG_DRM_SII902X) += sii902x.o
> diff --git a/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c b/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c
> new file mode 100644
> index 0000000..81e9279
> --- /dev/null
> +++ b/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c
> @@ -0,0 +1,405 @@
> +/*
> + * Driver for GE B850v3 DP display bridge
> +
> + * Copyright (c) 2016, Collabora Ltd.
> + * Copyright (c) 2016, General Electric Company
> +
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms and conditions of the GNU General Public License,
> + * version 2, as published by the Free Software Foundation.
> +
> + * This program is distributed in the hope it will be useful, but WITHOUT
> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
> + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
> + * more details.
> +
> + * You should have received a copy of the GNU General Public License
> + * along with this program. If not, see <http://www.gnu.org/licenses/>.
> +
> + * This driver creates a drm_bridge and a drm_connector for the LVDS to DP++
> + * display bridge of the GE B850v3. There are two physical bridges on the video
> + * signal pipeline: a STDP4028(LVDS to DP) and a STDP2690(DP to DP++). However
> + * the physical bridges are automatically configured by the input video signal,
> + * and the driver has no access to the video processing pipeline. The driver is
> + * only needed to read EDID from the STDP2690 and to handle HPD events from the
> + * STDP4028. The driver communicates with both bridges over i2c. The video
> + * signal pipeline is as follows:
> + *
> + * Host -> LVDS|--(STDP4028)--|DP -> DP|--(STDP2690)--|DP++ -> Video output
> + *
> + */
> +
> +#include <linux/gpio.h>
> +#include <linux/i2c.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <drm/drm_atomic.h>
> +#include <drm/drm_atomic_helper.h>
> +#include <drm/drm_crtc_helper.h>
> +#include <drm/drm_edid.h>
> +#include <drm/drmP.h>
> +
> +/*
> + * 220Mhz is a limitation of the host, as the bridge is capable of up to
> + * 330Mhz. See section 9.2.1.2.4 of the i.MX 6Dual/6Quad Applications
> + * Processor Reference Manual for more information about the 220Mhz limit.
> + * The imx-ldb driver will warn about clocks over 170Mhz, but it seem to work
> + * fine.
> + */
> +#define MAX_PIXEL_CLOCK 220000
> +
> +#define EDID_EXT_BLOCK_CNT 0x7E
> +
> +#define STDP4028_IRQ_OUT_CONF_REG 0x02
> +#define STDP4028_DPTX_IRQ_EN_REG 0x3C
> +#define STDP4028_DPTX_IRQ_STS_REG 0x3D
> +#define STDP4028_DPTX_STS_REG 0x3E
> +
> +#define STDP4028_DPTX_DP_IRQ_EN 0x1000
> +
> +#define STDP4028_DPTX_HOTPLUG_IRQ_EN 0x0400
> +#define STDP4028_DPTX_LINK_CH_IRQ_EN 0x2000
> +#define STDP4028_DPTX_IRQ_CONFIG \
> + (STDP4028_DPTX_LINK_CH_IRQ_EN | STDP4028_DPTX_HOTPLUG_IRQ_EN)
> +
> +#define STDP4028_DPTX_HOTPLUG_STS 0x0200
> +#define STDP4028_DPTX_LINK_STS 0x1000
> +#define STDP4028_CON_STATE_CONNECTED \
> + (STDP4028_DPTX_HOTPLUG_STS | STDP4028_DPTX_LINK_STS)
> +
> +#define STDP4028_DPTX_HOTPLUG_CH_STS 0x0400
> +#define STDP4028_DPTX_LINK_CH_STS 0x2000
> +#define STDP4028_DPTX_IRQ_CLEAR \
> + (STDP4028_DPTX_LINK_CH_STS | STDP4028_DPTX_HOTPLUG_CH_STS)
> +
> +struct ge_b850v3_lvds_dp {
> + struct drm_connector connector;
> + struct drm_bridge bridge;
> + struct i2c_client *ge_b850v3_lvds_dp_i2c;
> + struct i2c_client *edid_i2c;
> + struct edid *edid;
> + struct mutex lock;
> +};
> +
> +static inline struct ge_b850v3_lvds_dp *
> + bridge_to_ge_b850v3_lvds_dp(struct drm_bridge *bridge)
> +{
> + return container_of(bridge, struct ge_b850v3_lvds_dp, bridge);
> +}
> +
> +static inline struct ge_b850v3_lvds_dp *
> + connector_to_ge_b850v3_lvds_dp(struct drm_connector *connector)
> +{
> + return container_of(connector, struct ge_b850v3_lvds_dp, connector);
> +}
> +
> +u8 *stdp2690_get_edid(struct i2c_client *client)
> +{
> + struct i2c_adapter *adapter = client->adapter;
> + unsigned char start = 0x00;
> + unsigned int total_size;
> + u8 *block = kmalloc(EDID_LENGTH, GFP_KERNEL);
> +
> + struct i2c_msg msgs[] = {
> + {
> + .addr = client->addr,
> + .flags = 0,
> + .len = 1,
> + .buf = &start,
> + }, {
> + .addr = client->addr,
> + .flags = I2C_M_RD,
> + .len = EDID_LENGTH,
> + .buf = block,
> + }
> + };
> +
> + if (!block)
> + return NULL;
> +
> + if (i2c_transfer(adapter, msgs, 2) != 2) {
> + DRM_ERROR("Unable to read EDID.\n");
> + goto err;
> + }
> +
> + if (!drm_edid_block_valid(block, 0, false, NULL)) {
> + DRM_ERROR("Invalid EDID block\n");
> + goto err;
> + }
> +
> + total_size = (block[EDID_EXT_BLOCK_CNT] + 1) * EDID_LENGTH;
> + if (total_size > EDID_LENGTH) {
> + kfree(block);
> + block = kmalloc(total_size, GFP_KERNEL);
> + if (!block)
> + return NULL;
> +
> + /* Yes, read the entire buffer, and do not skip the first
> + * EDID_LENGTH bytes.
> + */
> + start = 0x00;
> + msgs[1].len = total_size;
> + msgs[1].buf = block;
> +
> + if (i2c_transfer(adapter, msgs, 2) != 2) {
> + DRM_ERROR("Unable to read EDID extension blocks.\n");
> + goto err;
> + }
> + }
> +
> + return block;
> +
> +err:
> + kfree(block);
> + return NULL;
> +}
> +
> +static int ge_b850v3_lvds_dp_get_modes(struct drm_connector *connector)
> +{
> + struct ge_b850v3_lvds_dp *ptn_bridge;
> + struct i2c_client *client;
> + int num_modes = 0;
> +
> + ptn_bridge = connector_to_ge_b850v3_lvds_dp(connector);
> + client = ptn_bridge->edid_i2c;
> +
> + mutex_lock(&ptn_bridge->lock);
> +
> + kfree(ptn_bridge->edid);
> + ptn_bridge->edid = (struct edid *) stdp2690_get_edid(client);
> +
> + if (ptn_bridge->edid) {
> + drm_mode_connector_update_edid_property(connector,
> + ptn_bridge->edid);
> + num_modes = drm_add_edid_modes(connector, ptn_bridge->edid);
> + }
> +
> + mutex_unlock(&ptn_bridge->lock);
> +
> + return num_modes;
> +}
> +
> +
> +static enum drm_mode_status ge_b850v3_lvds_dp_mode_valid(
> + struct drm_connector *connector, struct drm_display_mode *mode)
> +{
> + if (mode->clock > MAX_PIXEL_CLOCK) {
> + DRM_INFO("The pixel clock for the mode %s is too high, and not supported.",
> + mode->name);
> + return MODE_CLOCK_HIGH;
> + }
> +
> + return MODE_OK;
> +}
> +
> +static const struct
> +drm_connector_helper_funcs ge_b850v3_lvds_dp_connector_helper_funcs = {
> + .get_modes = ge_b850v3_lvds_dp_get_modes,
> + .mode_valid = ge_b850v3_lvds_dp_mode_valid,
> +};
> +
> +static enum drm_connector_status ge_b850v3_lvds_dp_detect(
> + struct drm_connector *connector, bool force)
> +{
> + struct ge_b850v3_lvds_dp *ptn_bridge =
> + connector_to_ge_b850v3_lvds_dp(connector);
> + struct i2c_client *ge_b850v3_lvds_dp_i2c =
> + ptn_bridge->ge_b850v3_lvds_dp_i2c;
> + s32 link_state;
> +
> + link_state = i2c_smbus_read_word_data(ge_b850v3_lvds_dp_i2c,
> + STDP4028_DPTX_STS_REG);
> +
> + if (link_state == STDP4028_CON_STATE_CONNECTED)
> + return connector_status_connected;
> +
> + if (link_state == 0)
> + return connector_status_disconnected;
> +
> + return connector_status_unknown;
> +}
> +
> +static const struct drm_connector_funcs ge_b850v3_lvds_dp_connector_funcs = {
> + .dpms = drm_atomic_helper_connector_dpms,
> + .fill_modes = drm_helper_probe_single_connector_modes,
> + .detect = ge_b850v3_lvds_dp_detect,
> + .destroy = drm_connector_cleanup,
> + .reset = drm_atomic_helper_connector_reset,
> + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
> + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
> +};
> +
> +static irqreturn_t ge_b850v3_lvds_dp_irq_handler(int irq, void *dev_id)
> +{
> + struct ge_b850v3_lvds_dp *ptn_bridge = dev_id;
> + struct i2c_client *ge_b850v3_lvds_dp_i2c
> + = ptn_bridge->ge_b850v3_lvds_dp_i2c;
> +
> + mutex_lock(&ptn_bridge->lock);
> +
> + i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
> + STDP4028_DPTX_IRQ_STS_REG, STDP4028_DPTX_IRQ_CLEAR);
> +
> + mutex_unlock(&ptn_bridge->lock);
> +
> + if (ptn_bridge->connector.dev)
> + drm_kms_helper_hotplug_event(ptn_bridge->connector.dev);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int ge_b850v3_lvds_dp_attach(struct drm_bridge *bridge)
> +{
> + struct ge_b850v3_lvds_dp *ptn_bridge
> + = bridge_to_ge_b850v3_lvds_dp(bridge);
> + struct drm_connector *connector = &ptn_bridge->connector;
> + struct i2c_client *ge_b850v3_lvds_dp_i2c
> + = ptn_bridge->ge_b850v3_lvds_dp_i2c;
> + int ret;
> +
> + if (!bridge->encoder) {
> + DRM_ERROR("Parent encoder object not found");
> + return -ENODEV;
> + }
> +
> + connector->polled = DRM_CONNECTOR_POLL_HPD;
> +
> + drm_connector_helper_add(connector,
> + &ge_b850v3_lvds_dp_connector_helper_funcs);
> +
> + ret = drm_connector_init(bridge->dev, connector,
> + &ge_b850v3_lvds_dp_connector_funcs,
> + DRM_MODE_CONNECTOR_DisplayPort);
> + if (ret) {
> + DRM_ERROR("Failed to initialize connector with drm\n");
> + return ret;
> + }
> +
> + drm_connector_register(connector);
Connectors shouldn't be registered in the bridge driver, they should
be registered by the kms driver after drm_dev_register is called.
The drm_connector_register_all() API is used for that.
> + ret = drm_mode_connector_attach_encoder(connector, bridge->encoder);
> + if (ret)
> + return ret;
> +
> + drm_bridge_enable(bridge);
This drm_bridge_enable() doesn't seem to serve any purpose here. It also
doesn't seem to make much sense to call drm_bridge_() funcs within a
bridge op itself.
> + if (ge_b850v3_lvds_dp_i2c->irq) {
> + drm_helper_hpd_irq_event(connector->dev);
> +
> + ret = devm_request_threaded_irq(&ge_b850v3_lvds_dp_i2c->dev,
> + ge_b850v3_lvds_dp_i2c->irq, NULL,
> + ge_b850v3_lvds_dp_irq_handler,
> + IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
> + "ge-b850v3-lvds-dp", ptn_bridge);
Is there a reason why we register the interrupt handler here and not in
probe?
Thanks,
Archit
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
More information about the linux-arm-kernel
mailing list