[PATCH v2 1/2] Documentation: dt: add bindings for ti-cpufreq

[Dave Gerlach]

Rob,
On 09/19/2016 04:14 PM, Rob Herring wrote:
> On Wed, Aug 31, 2016 at 09:53:27PM -0500, Dave Gerlach wrote:
>> Add the device tree bindings document for the TI CPUFreq/OPP driver
>> on AM33xx, AM43xx, DRA7, and AM57 SoCs. The operating-points-v2 binding
>> allows us to provide an opp-supported-hw property for each OPP to define
>> when it is available. This driver is responsible for reading and parsing
>> registers to determine which OPPs can be selectively enabled based
>> on the specific SoC in use by matching against the opp-supported-hw
>> data.
>
> Sorry, for the delay. Missed this somehow.
>
>>
>> Signed-off-by: Dave Gerlach <d-gerlach at ti.com>
>> ---
>> v1->v2:
>> 	- Dropped all driver/linux specific documentation
>> 	- Fixed some typos
>> 	- Add new compatibles for each SoC family to match against
>> 	- Switched to use am335x example to better demonstrate field one of
>> 	  opp-supported-hw.
>>
>>   .../devicetree/bindings/cpufreq/ti-cpufreq.txt     | 130 +++++++++++++++++++++
>>   1 file changed, 130 insertions(+)
>>   create mode 100644 Documentation/devicetree/bindings/cpufreq/ti-cpufreq.txt
>>
>> diff --git a/Documentation/devicetree/bindings/cpufreq/ti-cpufreq.txt b/Documentation/devicetree/bindings/cpufreq/ti-cpufreq.txt
>> new file mode 100644
>> index 000000000000..6276ae494121
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/cpufreq/ti-cpufreq.txt
>> @@ -0,0 +1,130 @@
>> +TI CPUFreq and OPP bindings
>> +================================
>> +
>> +Certain TI SoCs, like those in the am335x, am437x, am57xx, and dra7xx
>> +families support different OPPs depending on the silicon variant in use.
>> +The ti_cpufreq driver can use revision and an efuse value from the SoC to
>> +provide the OPP framework with supported hardware information. This is
>> +used to determine which OPPs from the operating-points-v2 table get enabled
>> +when it is parsed by the OPP framework.
>> +
>> +Required properties:
>> +--------------------
>> +In 'cpus' nodes:
>> +- operating-points-v2: Phandle to the operating-points-v2 table to use.
>> +- ti,syscon-efuse: Syscon phandle, offset to efuse register, efuse register
>> +		   mask, and efuse register shift to get the relevant bits
>> +		   that describe OPP availability.
>> +- ti,syscon-rev: Syscon and offset used to look up revision value on SoC.
>
> These have nothing to do with a cpu, so they don't belong here. Maybe
> the first is a property of an OPP table, but the second certainly is
> not.

Yes, I have no issue with this and will move the ti properties into the 
operating points table for v3 of the series.

>
>> +
>> +In 'operating-points-v2' table:
>> +- compatible: Should be
>> +	- 'operating-points-v2-ti-am3352-cpu' for am335x SoCs
>> +	- 'operating-points-v2-ti-am4372-cpu' for am43xx SoCs
>> +	- 'operating-points-v2-ti-dra7-cpu' for dra7xx/am57xx SoCs
>> +
>> +- opp-supported-hw: Two bitfields indicating:
>> +	1. Which revision of the SoC the OPP is supported by
>> +	2. Which eFuse bits indicate this OPP is available
>
> I tend to think you should handle this with kernel code (bootloader
> really) fixing up the OPP table as necessary rather than putting in DT.
>

The operating-points-v2 binding here [1] was designed with doing this in 
mind, and others are using it and the corresponding functionality 
offered by the OPP core to selectively enable OPPs. Why hide this in 
u-boot when we already have kernel framework support to do it?

Thanks for your comments, will send v3 moving the appropriate properties 
into the OPP table.

Regards,
Dave

[1] Documentation/devicetree/bindings/opp/opp.txt

> Rob
>