[PATCH v5 3/3] pci:aer: add support aer interrupt with none MSI/MSI-X/INTx mode

[Po Liu]

On some platforms, root port doesn't support MSI/MSI-X/INTx in RC mode.
When chip support the aer interrupt with none MSI/MSI-X/INTx mode,
maybe there is interrupt line for aer pme etc. Search the interrupt
number in the fdt file. Then fixup the dev->irq with it.

Signed-off-by: Po Liu <po.liu at nxp.com>
---
changes for v5:
	- Add clear 'aer' interrup-names description

 .../devicetree/bindings/pci/layerscape-pci.txt     | 11 +++++---
 drivers/pci/pcie/portdrv_core.c                    | 31 +++++++++++++++++++---
 2 files changed, 35 insertions(+), 7 deletions(-)

diff --git a/Documentation/devicetree/bindings/pci/layerscape-pci.txt b/Documentation/devicetree/bindings/pci/layerscape-pci.txt
index 41e9f55..101d0a7 100644
--- a/Documentation/devicetree/bindings/pci/layerscape-pci.txt
+++ b/Documentation/devicetree/bindings/pci/layerscape-pci.txt
@@ -18,8 +18,10 @@ Required properties:
 - reg: base addresses and lengths of the PCIe controller
 - interrupts: A list of interrupt outputs of the controller. Must contain an
   entry for each entry in the interrupt-names property.
-- interrupt-names: Must include the following entries:
-  "intr": The interrupt that is asserted for controller interrupts
+- interrupt-names: It may be include the following entries:
+  "aer": The interrupt that is asserted for aer interrupt
+  "pme": The interrupt that is asserted for pme interrupt
+  ......
 - fsl,pcie-scfg: Must include two entries.
   The first entry must be a link to the SCFG device node
   The second entry must be '0' or '1' based on physical PCIe controller index.
@@ -35,8 +37,9 @@ Example:
 		reg = <0x00 0x03400000 0x0 0x00010000   /* controller registers */
 		       0x40 0x00000000 0x0 0x00002000>; /* configuration space */
 		reg-names = "regs", "config";
-		interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */
-		interrupt-names = "intr";
+		interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>, /* aer interrupt */
+			<GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>; /* pme interrupt */
+		interrupt-names = "aer", "pme";
 		fsl,pcie-scfg = <&scfg 0>;
 		#address-cells = <3>;
 		#size-cells = <2>;
diff --git a/drivers/pci/pcie/portdrv_core.c b/drivers/pci/pcie/portdrv_core.c
index e9270b4..7c4943d 100644
--- a/drivers/pci/pcie/portdrv_core.c
+++ b/drivers/pci/pcie/portdrv_core.c
@@ -16,6 +16,7 @@
 #include <linux/slab.h>
 #include <linux/pcieport_if.h>
 #include <linux/aer.h>
+#include <linux/of_irq.h>
 
 #include "../pci.h"
 #include "portdrv.h"
@@ -200,6 +201,28 @@ static int pcie_port_enable_msix(struct pci_dev *dev, int *vectors, int mask)
 static int init_service_irqs(struct pci_dev *dev, int *irqs, int mask)
 {
 	int i, irq = -1;
+	int ret;
+	struct device_node *np = NULL;
+
+	for (i = 0; i < PCIE_PORT_DEVICE_MAXSERVICES; i++)
+		irqs[i] = 0;
+
+	if (dev->bus->dev.of_node)
+		np = dev->bus->dev.of_node;
+
+	/* If root port doesn't support MSI/MSI-X/INTx in RC mode,
+	 * request irq for aer
+	 */
+	if (IS_ENABLED(CONFIG_OF_IRQ) && np &&
+			(mask & PCIE_PORT_SERVICE_PME)) {
+		ret = of_irq_get_byname(np, "aer");
+		if (ret > 0) {
+			irqs[PCIE_PORT_SERVICE_AER_SHIFT] = ret;
+			if (dev->irq)
+				irq = dev->irq;
+			goto no_msi;
+		}
+	}
 
 	/*
 	 * If MSI cannot be used for PCIe PME or hotplug, we have to use
@@ -225,11 +248,13 @@ static int init_service_irqs(struct pci_dev *dev, int *irqs, int mask)
 		irq = dev->irq;
 
  no_msi:
-	for (i = 0; i < PCIE_PORT_DEVICE_MAXSERVICES; i++)
-		irqs[i] = irq;
+	for (i = 0; i < PCIE_PORT_DEVICE_MAXSERVICES; i++) {
+		if (!irqs[i])
+			irqs[i] = irq;
+	}
 	irqs[PCIE_PORT_SERVICE_VC_SHIFT] = -1;
 
-	if (irq < 0)
+	if (irq < 0 && irqs[PCIE_PORT_SERVICE_AER_SHIFT] < 0)
 		return -ENODEV;
 	return 0;
 }
-- 
2.1.0.27.g96db324