[PATCH v1 1/2] ARM: dts: add rockchip PX3 Evaluation board
Andy Yan
andy.yan at rock-chips.com
Sat Sep 10 10:44:00 PDT 2016
PX3 EVB is designed by Rockchip for automotive field,
which intergrated with CVBS(TP2825)/MIPI DSI/LVDS/HDMI
video input/output interface, WIFI/BT/GPS(on a module
named S500 which based on MT6620), Gsensor BMA250E and
light&proximity sensor STK3410.
Signed-off-by: Andy Yan <andy.yan at rock-chips.com>
---
Changes in v1:
- board rename
- add vendor prefix for i2c interfaced sensors
- use stdout-path to set the default console
Documentation/devicetree/bindings/arm/rockchip.txt | 4 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/rk3188-px3-evb.dts | 337 +++++++++++++++++++++
3 files changed, 342 insertions(+)
create mode 100644 arch/arm/boot/dts/rk3188-px3-evb.dts
diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt
index 6668645..6da3881 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.txt
+++ b/Documentation/devicetree/bindings/arm/rockchip.txt
@@ -21,6 +21,10 @@ Rockchip platforms device tree bindings
Required root node properties:
- compatible = "radxa,rock", "rockchip,rk3188";
+- Rockchip PX3 Evaluation board:
+ Required root node properties:
+ - compatible = "rockchip,px3-evb", "rockchip,px3", "rockchip,rk3188";
+
- Radxa Rock2 Square board:
Required root node properties:
- compatible = "radxa,rock2-square", "rockchip,rk3288";
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index faacd52..88d27a2 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -620,6 +620,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
rk3066a-marsboard.dtb \
rk3066a-rayeager.dtb \
rk3188-radxarock.dtb \
+ rk3188-px3-evb.dtb \
rk3228-evb.dtb \
rk3229-evb.dtb \
rk3288-evb-act8846.dtb \
diff --git a/arch/arm/boot/dts/rk3188-px3-evb.dts b/arch/arm/boot/dts/rk3188-px3-evb.dts
new file mode 100644
index 0000000..f6bc738
--- /dev/null
+++ b/arch/arm/boot/dts/rk3188-px3-evb.dts
@@ -0,0 +1,337 @@
+/*
+ * Copyright (c) 2016 Andy Yan <andy.yan at rock-chips.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include "rk3188.dtsi"
+
+/ {
+ model = "Rockchip PX3-EVB";
+ compatible = "rockchip,px3-evb", "rockchip,px3", "rockchip,rk3188";
+
+ chosen {
+ stdout-path = "serial2:115200n8";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x60000000 0x80000000>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ autorepeat;
+
+ power {
+ gpios = <&gpio0 4 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ label = "GPIO Key Power";
+ linux,input-type = <1>;
+ wakeup-source;
+ debounce-interval = <100>;
+ };
+ };
+
+ vcc_sys: vsys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vsys";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ };
+};
+
+&cpu0 {
+ cpu0-supply = <&vdd_cpu>;
+};
+
+&i2c0 {
+ status = "okay";
+
+ /* Accelerometer */
+ bma250 at 18 {
+ compatible = "bosch,bma250";
+ reg = <0x18>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ stk3410 at 48 {
+ compatible = "sensortek,STK3310";
+ reg = <0x48>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+ rk808: pmic at 1c {
+ compatible = "rockchip,rk818";
+ reg = <0x1c>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ rockchip,system-power-controller;
+ wakeup-source;
+ #clock-cells = <1>;
+ clock-output-names = "xin32k", "rk808-clkout2";
+
+ vcc1-supply = <&vcc_sys>;
+ vcc2-supply = <&vcc_sys>;
+ vcc3-supply = <&vcc_sys>;
+ vcc4-supply = <&vcc_sys>;
+ vcc6-supply = <&vcc_sys>;
+ vcc7-supply = <&vcc_sys>;
+ vcc8-supply = <&vcc_io>;
+ vcc9-supply = <&vcc_io>;
+
+ regulators {
+ vdd_cpu: DCDC_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-name = "vdd_arm";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu: DCDC_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-name = "vdd_gpu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc_ddr";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_io: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc_io";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_cif: LDO_REG1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc_cif";
+ };
+
+ vcc_jetta33: LDO_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc_jetta33";
+ };
+
+ vdd_10: LDO_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-name = "vdd_10";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ lvds_12: LDO_REG4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "lvds_12";
+ };
+
+ lvds_25: LDO_REG5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "lvds_25";
+ };
+
+ cif_18: LDO_REG6 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-name = "cif_18";
+ };
+
+ vcc_sd: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc_sd";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ wl_18: LDO_REG8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "wl_18";
+ };
+
+ lcd_33: SWITCH_REG1 {
+ regulator-name = "lcd_33";
+ };
+ };
+ };
+
+};
+
+&i2c2 {
+ gsl1680: touchscreen at 40 {
+ compatible = "silead,gsl1680";
+ reg = <0x40>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <15 IRQ_TYPE_EDGE_FALLING>;
+ power-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+ touchscreen-size-x = <800>;
+ touchscreen-size-y = <1280>;
+ silead,max-fingers = <5>;
+ };
+};
+
+&emmc {
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ disable-wp;
+ non-removable;
+ num-slots = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_rst>;
+ status = "okay";
+};
+
+&mmc0 {
+ num-slots = <1>;
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd0_clk>, <&sd0_cmd>, <&sd0_cd>, <&sd0_bus4>;
+ vmmc-supply = <&vcc_sd>;
+
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ disable-wp;
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+&pwm2 {
+ status = "okay";
+};
+
+&pwm3 {
+ status = "okay";
+};
+
+&pinctrl {
+ pcfg_output_low: pcfg-output-low {
+ output-low;
+ };
+
+ usb {
+ host_vbus_drv: host-vbus-drv {
+ rockchip,pins = <0 3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ otg_vbus_drv: otg-vbus-drv {
+ rockchip,pins = <2 31 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+};
+
+&usb_host {
+ status = "okay";
+};
+
+&usb_otg {
+ status = "okay";
+};
+
+&wdt {
+ status = "okay";
+};
--
2.7.4
More information about the linux-arm-kernel
mailing list