[PATCH V2 7/7] thermal: qoriq: Add thermal management support

Troy Jia hongtao.jia at nxp.com
Thu Sep 8 00:11:45 PDT 2016



> -----Original Message-----
> From: Zhang Rui [mailto:rui.zhang at intel.com]
> Sent: Friday, August 19, 2016 8:40 PM
> To: Hongtao Jia <hongtao.jia at nxp.com>; edubezval at gmail.com;
> robh+dt at kernel.org; galak at codeaurora.org; Scott Wood
> <scott.wood at nxp.com>; shawnguo at kernel.org
> Cc: linux-pm at vger.kernel.org; devicetree at vger.kernel.org; linux-
> kernel at vger.kernel.org; linuxppc-dev at lists.ozlabs.org; linux-arm-
> kernel at lists.infradead.org
> Subject: Re: [PATCH V2 7/7] thermal: qoriq: Add thermal management support
> 
> On 四, 2016-06-30 at 11:08 +0800, Jia Hongtao wrote:
> > This driver add thermal management support by enabling TMU (Thermal
> > Monitoring Unit) on QorIQ platform.
> >
> > It's based on thermal of framework:
> > - Trip points defined in device tree.
> > - Cpufreq as cooling device registered in qoriq cpufreq driver.
> >
> > Signed-off-by: Jia Hongtao <hongtao.jia at nxp.com>
> 
> The patch looks good to me.
> I only need to take this patch, right?
> 
> thanks,
> rui

Yes. You just need to take this patch.
Sorry for the late response. I was on my long vacation back then.

Thanks,
Hongtao.

> > ---
> > Changes of V2:
> > * Add HAS_IOMEM dependency to fix build error on UM
> >
> >  drivers/thermal/Kconfig         |  10 ++
> >  drivers/thermal/Makefile        |   1 +
> >  drivers/thermal/qoriq_thermal.c | 328
> > ++++++++++++++++++++++++++++++++++++++++
> >  3 files changed, 339 insertions(+)
> >  create mode 100644 drivers/thermal/qoriq_thermal.c
> >
> > diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
> > index 2d702ca..56ef30d 100644
> > --- a/drivers/thermal/Kconfig
> > +++ b/drivers/thermal/Kconfig
> > @@ -195,6 +195,16 @@ config IMX_THERMAL
> >  	  cpufreq is used as the cooling device to throttle CPUs
> > when the
> >  	  passive trip is crossed.
> >
> > +config QORIQ_THERMAL
> > +	tristate "QorIQ Thermal Monitoring Unit"
> > +	depends on THERMAL_OF
> > +	depends on HAS_IOMEM
> > +	help
> > +	  Support for Thermal Monitoring Unit (TMU) found on QorIQ
> > platforms.
> > +	  It supports one critical trip point and one passive trip
> > point. The
> > +	  cpufreq is used as the cooling device to throttle CPUs
> > when the
> > +	  passive trip is crossed.
> > +
> >  config SPEAR_THERMAL
> >  	tristate "SPEAr thermal sensor driver"
> >  	depends on PLAT_SPEAR || COMPILE_TEST
> > diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
> > index 10b07c1..6662232 100644
> > --- a/drivers/thermal/Makefile
> > +++ b/drivers/thermal/Makefile
> > @@ -37,6 +37,7 @@ obj-$(CONFIG_DB8500_THERMAL)	+=
> > db8500_thermal.o
> >  obj-$(CONFIG_ARMADA_THERMAL)	+= armada_thermal.o
> >  obj-$(CONFIG_TANGO_THERMAL)	+= tango_thermal.o
> >  obj-$(CONFIG_IMX_THERMAL)	+= imx_thermal.o
> > +obj-$(CONFIG_QORIQ_THERMAL)	+= qoriq_thermal.o
> >  obj-$(CONFIG_DB8500_CPUFREQ_COOLING)	+=
> > db8500_cpufreq_cooling.o
> >  obj-$(CONFIG_INTEL_POWERCLAMP)	+= intel_powerclamp.o
> >  obj-$(CONFIG_X86_PKG_TEMP_THERMAL)	+= x86_pkg_temp_thermal.o
> > diff --git a/drivers/thermal/qoriq_thermal.c
> > b/drivers/thermal/qoriq_thermal.c
> > new file mode 100644
> > index 0000000..644ba52
> > --- /dev/null
> > +++ b/drivers/thermal/qoriq_thermal.c
> > @@ -0,0 +1,328 @@
> > +/*
> > + * Copyright 2016 Freescale Semiconductor, Inc.
> > + *
> > + * This program is free software; you can redistribute it and/or
> > modify it
> > + * under the terms and conditions of the GNU General Public License,
> > + * version 2, as published by the Free Software Foundation.
> > + *
> > + * This program is distributed in the hope it will be useful, but
> > WITHOUT
> > + * ANY WARRANTY; without even the implied warranty of
> > MERCHANTABILITY or
> > + * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public
> > License for
> > + * more details.
> > + *
> > + */
> > +
> > +#include <linux/module.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/err.h>
> > +#include <linux/io.h>
> > +#include <linux/of.h>
> > +#include <linux/of_address.h>
> > +#include <linux/thermal.h>
> > +
> > +#include "thermal_core.h"
> > +
> > +#define SITES_MAX	16
> > +
> > +/*
> > + * QorIQ TMU Registers
> > + */
> > +struct qoriq_tmu_site_regs {
> > +	u32 tritsr;		/* Immediate Temperature Site
> > Register */
> > +	u32 tratsr;		/* Average Temperature Site
> > Register */
> > +	u8 res0[0x8];
> > +};
> > +
> > +struct qoriq_tmu_regs {
> > +	u32 tmr;		/* Mode Register */
> > +#define TMR_DISABLE	0x0
> > +#define TMR_ME		0x80000000
> > +#define TMR_ALPF	0x0c000000
> > +	u32 tsr;		/* Status Register */
> > +	u32 tmtmir;		/* Temperature measurement
> > interval Register */
> > +#define TMTMIR_DEFAULT	0x0000000f
> > +	u8 res0[0x14];
> > +	u32 tier;		/* Interrupt Enable Register */
> > +#define TIER_DISABLE	0x0
> > +	u32 tidr;		/* Interrupt Detect Register */
> > +	u32 tiscr;		/* Interrupt Site Capture Register
> > */
> > +	u32 ticscr;		/* Interrupt Critical Site
> > Capture Register */
> > +	u8 res1[0x10];
> > +	u32 tmhtcrh;		/* High Temperature Capture
> > Register */
> > +	u32 tmhtcrl;		/* Low Temperature Capture
> > Register */
> > +	u8 res2[0x8];
> > +	u32 tmhtitr;		/* High Temperature Immediate
> > Threshold */
> > +	u32 tmhtatr;		/* High Temperature Average
> > Threshold */
> > +	u32 tmhtactr;	/* High Temperature Average Crit
> > Threshold */
> > +	u8 res3[0x24];
> > +	u32 ttcfgr;		/* Temperature Configuration
> > Register */
> > +	u32 tscfgr;		/* Sensor Configuration Register
> > */
> > +	u8 res4[0x78];
> > +	struct qoriq_tmu_site_regs site[SITES_MAX];
> > +	u8 res5[0x9f8];
> > +	u32 ipbrr0;		/* IP Block Revision Register 0
> > */
> > +	u32 ipbrr1;		/* IP Block Revision Register 1
> > */
> > +	u8 res6[0x310];
> > +	u32 ttr0cr;		/* Temperature Range 0 Control
> > Register */
> > +	u32 ttr1cr;		/* Temperature Range 1 Control
> > Register */
> > +	u32 ttr2cr;		/* Temperature Range 2 Control
> > Register */
> > +	u32 ttr3cr;		/* Temperature Range 3 Control
> > Register */
> > +};
> > +
> > +/*
> > + * Thermal zone data
> > + */
> > +struct qoriq_tmu_data {
> > +	struct thermal_zone_device *tz;
> > +	struct qoriq_tmu_regs __iomem *regs;
> > +	int sensor_id;
> > +	bool little_endian;
> > +};
> > +
> > +static void tmu_write(struct qoriq_tmu_data *p, u32 val, void
> > __iomem *addr)
> > +{
> > +	if (p->little_endian)
> > +		iowrite32(val, addr);
> > +	else
> > +		iowrite32be(val, addr);
> > +}
> > +
> > +static u32 tmu_read(struct qoriq_tmu_data *p, void __iomem *addr)
> > +{
> > +	if (p->little_endian)
> > +		return ioread32(addr);
> > +	else
> > +		return ioread32be(addr);
> > +}
> > +
> > +static int tmu_get_temp(void *p, int *temp)
> > +{
> > +	u32 val;
> > +	struct qoriq_tmu_data *data = p;
> > +
> > +	val = tmu_read(data, &data->regs->site[data-
> > >sensor_id].tritsr);
> > +	*temp = (val & 0xff) * 1000;
> > +
> > +	return 0;
> > +}
> > +
> > +static int qoriq_tmu_get_sensor_id(void)
> > +{
> > +	int ret, id;
> > +	struct of_phandle_args sensor_specs;
> > +	struct device_node *np, *sensor_np;
> > +
> > +	np = of_find_node_by_name(NULL, "thermal-zones");
> > +	if (!np)
> > +		return -ENODEV;
> > +
> > +	sensor_np = of_get_next_child(np, NULL);
> > +	ret = of_parse_phandle_with_args(sensor_np, "thermal-
> > sensors",
> > +			"#thermal-sensor-cells",
> > +			0, &sensor_specs);
> > +	if (ret) {
> > +		of_node_put(np);
> > +		of_node_put(sensor_np);
> > +		return ret;
> > +	}
> > +
> > +	if (sensor_specs.args_count >= 1) {
> > +		id = sensor_specs.args[0];
> > +		WARN(sensor_specs.args_count > 1,
> > +				"%s: too many cells in sensor
> > specifier %d\n",
> > +				sensor_specs.np->name,
> > sensor_specs.args_count);
> > +	} else {
> > +		id = 0;
> > +	}
> > +
> > +	of_node_put(np);
> > +	of_node_put(sensor_np);
> > +
> > +	return id;
> > +}
> > +
> > +static int qoriq_tmu_calibration(struct platform_device *pdev)
> > +{
> > +	int i, val, len;
> > +	u32 range[4];
> > +	const u32 *calibration;
> > +	struct device_node *np = pdev->dev.of_node;
> > +	struct qoriq_tmu_data *data = platform_get_drvdata(pdev);
> > +
> > +	if (of_property_read_u32_array(np, "fsl,tmu-range", range,
> > 4)) {
> > +		dev_err(&pdev->dev, "missing calibration range.\n");
> > +		return -ENODEV;
> > +	}
> > +
> > +	/* Init temperature range registers */
> > +	tmu_write(data, range[0], &data->regs->ttr0cr);
> > +	tmu_write(data, range[1], &data->regs->ttr1cr);
> > +	tmu_write(data, range[2], &data->regs->ttr2cr);
> > +	tmu_write(data, range[3], &data->regs->ttr3cr);
> > +
> > +	calibration = of_get_property(np, "fsl,tmu-calibration",
> > &len);
> > +	if (calibration == NULL || len % 8) {
> > +		dev_err(&pdev->dev, "invalid calibration data.\n");
> > +		return -ENODEV;
> > +	}
> > +
> > +	for (i = 0; i < len; i += 8, calibration += 2) {
> > +		val = of_read_number(calibration, 1);
> > +		tmu_write(data, val, &data->regs->ttcfgr);
> > +		val = of_read_number(calibration + 1, 1);
> > +		tmu_write(data, val, &data->regs->tscfgr);
> > +	}
> > +
> > +	return 0;
> > +}
> > +
> > +static void qoriq_tmu_init_device(struct qoriq_tmu_data *data)
> > +{
> > +	/* Disable interrupt, using polling instead */
> > +	tmu_write(data, TIER_DISABLE, &data->regs->tier);
> > +
> > +	/* Set update_interval */
> > +	tmu_write(data, TMTMIR_DEFAULT, &data->regs->tmtmir);
> > +
> > +	/* Disable monitoring */
> > +	tmu_write(data, TMR_DISABLE, &data->regs->tmr);
> > +}
> > +
> > +static struct thermal_zone_of_device_ops tmu_tz_ops = {
> > +	.get_temp = tmu_get_temp,
> > +};
> > +
> > +static int qoriq_tmu_probe(struct platform_device *pdev)
> > +{
> > +	int ret;
> > +	const struct thermal_trip *trip;
> > +	struct qoriq_tmu_data *data;
> > +	struct device_node *np = pdev->dev.of_node;
> > +	u32 site = 0;
> > +
> > +	if (!np) {
> > +		dev_err(&pdev->dev, "Device OF-Node is NULL");
> > +		return -ENODEV;
> > +	}
> > +
> > +	data = devm_kzalloc(&pdev->dev, sizeof(struct
> > qoriq_tmu_data),
> > +			    GFP_KERNEL);
> > +	if (!data)
> > +		return -ENOMEM;
> > +
> > +	platform_set_drvdata(pdev, data);
> > +
> > +	data->little_endian = of_property_read_bool(np, "little-
> > endian");
> > +
> > +	data->sensor_id = qoriq_tmu_get_sensor_id();
> > +	if (data->sensor_id < 0) {
> > +		dev_err(&pdev->dev, "Failed to get sensor id\n");
> > +		ret = -ENODEV;
> > +		goto err_iomap;
> > +	}
> > +
> > +	data->regs = of_iomap(np, 0);
> > +	if (!data->regs) {
> > +		dev_err(&pdev->dev, "Failed to get memory
> > region\n");
> > +		ret = -ENODEV;
> > +		goto err_iomap;
> > +	}
> > +
> > +	qoriq_tmu_init_device(data);	/* TMU initialization */
> > +
> > +	ret = qoriq_tmu_calibration(pdev);	/* TMU calibration
> > */
> > +	if (ret < 0)
> > +		goto err_tmu;
> > +
> > +	data->tz = thermal_zone_of_sensor_register(&pdev->dev, data-
> > >sensor_id,
> > +				data, &tmu_tz_ops);
> > +	if (IS_ERR(data->tz)) {
> > +		ret = PTR_ERR(data->tz);
> > +		dev_err(&pdev->dev,
> > +			"Failed to register thermal zone device
> > %d\n", ret);
> > +		goto err_tmu;
> > +	}
> > +
> > +	trip = of_thermal_get_trip_points(data->tz);
> > +
> > +	/* Enable monitoring */
> > +	site |= 0x1 << (15 - data->sensor_id);
> > +	tmu_write(data, site | TMR_ME | TMR_ALPF, &data->regs->tmr);
> > +
> > +	return 0;
> > +
> > +err_tmu:
> > +	iounmap(data->regs);
> > +
> > +err_iomap:
> > +	platform_set_drvdata(pdev, NULL);
> > +
> > +	return ret;
> > +}
> > +
> > +static int qoriq_tmu_remove(struct platform_device *pdev)
> > +{
> > +	struct qoriq_tmu_data *data = platform_get_drvdata(pdev);
> > +
> > +	thermal_zone_of_sensor_unregister(&pdev->dev, data->tz);
> > +
> > +	/* Disable monitoring */
> > +	tmu_write(data, TMR_DISABLE, &data->regs->tmr);
> > +
> > +	iounmap(data->regs);
> > +	platform_set_drvdata(pdev, NULL);
> > +
> > +	return 0;
> > +}
> > +
> > +#ifdef CONFIG_PM_SLEEP
> > +static int qoriq_tmu_suspend(struct device *dev)
> > +{
> > +	u32 tmr;
> > +	struct qoriq_tmu_data *data = dev_get_drvdata(dev);
> > +
> > +	/* Disable monitoring */
> > +	tmr = tmu_read(data, &data->regs->tmr);
> > +	tmr &= ~TMR_ME;
> > +	tmu_write(data, tmr, &data->regs->tmr);
> > +
> > +	return 0;
> > +}
> > +
> > +static int qoriq_tmu_resume(struct device *dev)
> > +{
> > +	u32 tmr;
> > +	struct qoriq_tmu_data *data = dev_get_drvdata(dev);
> > +
> > +	/* Enable monitoring */
> > +	tmr = tmu_read(data, &data->regs->tmr);
> > +	tmr |= TMR_ME;
> > +	tmu_write(data, tmr, &data->regs->tmr);
> > +
> > +	return 0;
> > +}
> > +#endif
> > +
> > +static SIMPLE_DEV_PM_OPS(qoriq_tmu_pm_ops,
> > +			 qoriq_tmu_suspend, qoriq_tmu_resume);
> > +
> > +static const struct of_device_id qoriq_tmu_match[] = {
> > +	{ .compatible = "fsl,qoriq-tmu", },
> > +	{},
> > +};
> > +MODULE_DEVICE_TABLE(of, qoriq_tmu_match);
> > +
> > +static struct platform_driver qoriq_tmu = {
> > +	.driver	= {
> > +		.name		= "qoriq_thermal",
> > +		.pm		= &qoriq_tmu_pm_ops,
> > +		.of_match_table	= qoriq_tmu_match,
> > +	},
> > +	.probe	= qoriq_tmu_probe,
> > +	.remove	= qoriq_tmu_remove,
> > +};
> > +module_platform_driver(qoriq_tmu);
> > +
> > +MODULE_AUTHOR("Jia Hongtao <hongtao.jia at nxp.com>");
> > +MODULE_DESCRIPTION("QorIQ Thermal Monitoring Unit driver");
> > +MODULE_LICENSE("GPL v2");
> > --
> > 2.1.0.27.g96db324
> >


More information about the linux-arm-kernel mailing list