[PATCH 1/2] mtd: nand: automate NAND timings selection

[Boris Brezillon]

On Tue, 6 Sep 2016 10:23:02 +0200
Sascha Hauer <s.hauer at pengutronix.de> wrote:

> Hi Boris,
> 
> On Fri, Sep 02, 2016 at 02:42:28PM +0200, Sascha Hauer wrote:
> > +static int nand_configure_data_interface(struct mtd_info *mtd)
> > +{
> > +	struct nand_chip *chip = mtd_to_nand(mtd);
> > +	struct nand_data_interface *conf;
> > +	int modes, mode, ret = -EINVAL;
> > +	uint8_t tmode_param[ONFI_SUBFEATURE_PARAM_LEN] = { };
> > +	int i;
> > +
> > +	conf = kzalloc(sizeof(*conf), GFP_KERNEL);
> > +	if (!conf)
> > +		return -ENOMEM;
> > +
> > +	/* TODO: support DDR interfaces */
> > +	conf->type = NAND_SDR_IFACE;
> > +
> > +	/*
> > +	 * First try to identify the best timings from ONFI parameters and
> > +	 * if the NAND does not support ONFI, fallback to the default ONFI
> > +	 * timing mode.
> > +	 */
> > +	modes = onfi_get_async_timing_mode(chip);
> > +	if (modes == ONFI_TIMING_MODE_UNKNOWN) {
> > +		mode = chip->onfi_timing_mode_default;
> > +		conf->timings.sdr =
> > +				*onfi_async_timing_mode_to_sdr_timings(mode);
> > +
> > +		ret = nand_check_data_interface(mtd, conf);
> > +	} else {
> > +		for (mode = fls(modes) - 1; mode >= 0; mode--) {
> > +			conf->timings.sdr =
> > +				*onfi_async_timing_mode_to_sdr_timings(mode);
> > +
> > +			ret = nand_check_data_interface(mtd, conf);
> > +			if (!ret)
> > +				break;
> > +		}
> > +	}  
> 
> I wonder if this works good for non ONFI NANDs. In the ONFI case we
> iterate over all modes supported by the NAND until we find one that also
> suits the driver. By doing so we inherently assume that not all drivers
> support all modes. In the non ONFI case instead we hardcode a single
> timing into the nand_id table, what if the driver does not support this
> timing? It will fail in this case without ever trying slower timings.
> Shouldn't we encode the mode bitmask into the nand_id table rather than
> a single timing?

IIRC, this is what I proposed in my first patch (having a bitmask
encoding supported modes), but Brian suggested to directly put the
highest supported mode.

Anyway, I don't think a NAND can support higher modes without
supporting lower ones, so extracting the supported modes info from the
default_onfi_timing_mode should be pretty easy:

	supported_modes = GENMASK(default_onfi_timing_mode, 0);

> I cannot find a chip in the nand_id table which actually sets
> onfi_timing_mode_default, but since you introduced the field in the
> nand_id table with commit 57a94e24bc92 you can probably tell me more.

Hm, this one [1] is defining timing mode 4.

[1]http://lxr.free-electrons.com/source/drivers/mtd/nand/nand_ids.c#L51