[v14 PATCH 2/5] phy: Add USB Type-C PHY driver for rk3399
Kishon Vijay Abraham I
kishon at ti.com
Mon Sep 5 21:09:02 PDT 2016
On Wednesday 24 August 2016 10:47 AM, Chris Zhong wrote:
> Add a PHY provider driver for the rk3399 SoC Type-c PHY. The USB
> Type-C PHY is designed to support the USB3 and DP applications.
> The USB3 operates in SuperSpeed mode and the DP can operate at RBR,
> HBR and HBR2 data rates. This driver create 2 PHY devices separately
> for USB3 and DisplyPort, and registers them under the child node.
>
> Signed-off-by: Chris Zhong <zyw at rock-chips.com>
> Signed-off-by: Kever Yang <kever.yang at rock-chips.com>
> Reviewed-by: Guenter Roeck <groeck at chromium.org>
> Tested-by: Guenter Roeck <groeck at chromium.org>
merged, thanks.
-Kishon
>
> ---
>
> Changes in v14:
> - change the name of property from super speed to EXTCON_PROP_USB_SS
>
> Changes in v13:
> - add some description in front of driver
> - change name of usb to usb3
> - add a USB3 RX register configuration
> - do not return err if nothing connected with Type-C, when usb phy power on,
> since the USB core driver will call phy power without USB3 device connected.
>
> Changes in v12:
> - enable DP+USB3 mode, only when EXTCON_PROP_USB_SUPERSPEED equal 1
> and DP is attached
>
> Changes in v11:
> - make a clearer demarcation between usb phy and dp phy.
>
> Changes in v10:
> - do not control dp select and hpd config in phy driver
>
> Changes in v9:
> - the new_mode should be int not u8
> - move mutex_lock(&tcphy->lock); to earlier place. in
> rockchip_usb3_phy_power_off
> - better mutex lock for phy mode and flip
> - split the Type-C PHY into two PHYs: USB3 and DP
>
> Changes in v8:
> - set the default cable id to EXTCON_USB_HOST
> - optimization Error log
>
> Changes in v7:
> - support new API of extcon
>
> Changes in v6:
> - delete the support of PIN_ASSIGN_A/B
> - set the default mode to MODE_DFP_USB
> - disable DP PLL at USB3 only mode
>
> Changes in v5:
> - support get property from extcon
> - remove PIN ASSIGN A/B support
>
> Changes in v4:
> - select EXTCON
> - use phy framework to control the USB3 and DP function
> - rename PIN_MAP_ to PIN_ASSIGN_
>
> Changes in v3:
> - remove the phy framework(Kishon Vijay Abraham I)
> - add parentheses around the macro
> - use a single space between type and name
> - add spaces after opening and before closing braces.
> - use u16 for register value
> - remove type-c phy header file
> - CodingStyle optimization
> - use some cable extcon to get type-c port information
> - add a extcon to notify Display Port
>
> Changes in v2:
> - select RESET_CONTROLLER
> - alphabetic order
> - modify some spelling mistakes
> - make mode cleaner
> - use bool for enable/disable
> - check all of the return value
> - return a better err number
> - use more readx_poll_timeout()
> - clk_disable_unprepare(tcphy->clk_ref);
> - remove unuse functions, rockchip_typec_phy_power_on/off
> - remove unnecessary typecast from void *
> - use dts node to distinguish between phys.
>
> Changes in v1:
> - update the licence note
> - init core clock to 50MHz
> - use extcon API
> - remove unused global
> - add some comments for magic num
> - change usleep_range(1000, 2000) tousleep_range(1000, 1050)
> - remove __func__ from dev_err
> - return err number when get clk failed
> - remove ADDR_ADJ define
> - use devm_clk_get(&pdev->dev, "tcpdcore")
>
> drivers/phy/Kconfig | 9 +
> drivers/phy/Makefile | 1 +
> drivers/phy/phy-rockchip-typec.c | 1013 ++++++++++++++++++++++++++++++++++++++
> 3 files changed, 1023 insertions(+)
> create mode 100644 drivers/phy/phy-rockchip-typec.c
>
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index 42f3e30..c775fd7 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -348,6 +348,15 @@ config PHY_ROCKCHIP_PCIE
> help
> Enable this to support the Rockchip PCIe PHY.
>
> +config PHY_ROCKCHIP_TYPEC
> + tristate "Rockchip TYPEC PHY Driver"
> + depends on OF && (ARCH_ROCKCHIP || COMPILE_TEST)
> + select EXTCON
> + select GENERIC_PHY
> + select RESET_CONTROLLER
> + help
> + Enable this to support the Rockchip USB TYPEC PHY.
> +
> config PHY_ST_SPEAR1310_MIPHY
> tristate "ST SPEAR1310-MIPHY driver"
> select GENERIC_PHY
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index fbb91e7..5d58b63 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -39,6 +39,7 @@ obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2) += phy-rockchip-inno-usb2.o
> obj-$(CONFIG_PHY_ROCKCHIP_EMMC) += phy-rockchip-emmc.o
> obj-$(CONFIG_PHY_ROCKCHIP_PCIE) += phy-rockchip-pcie.o
> obj-$(CONFIG_PHY_ROCKCHIP_DP) += phy-rockchip-dp.o
> +obj-$(CONFIG_PHY_ROCKCHIP_TYPEC) += phy-rockchip-typec.o
> obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA) += phy-qcom-ipq806x-sata.o
> obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY) += phy-spear1310-miphy.o
> obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY) += phy-spear1340-miphy.o
> diff --git a/drivers/phy/phy-rockchip-typec.c b/drivers/phy/phy-rockchip-typec.c
> new file mode 100644
> index 0000000..fb58a27
> --- /dev/null
> +++ b/drivers/phy/phy-rockchip-typec.c
> @@ -0,0 +1,1013 @@
> +/*
> + * Copyright (C) Fuzhou Rockchip Electronics Co.Ltd
> + * Author: Chris Zhong <zyw at rock-chips.com>
> + * Kever Yang <kever.yang at rock-chips.com>
> + *
> + * This software is licensed under the terms of the GNU General Public
> + * License version 2, as published by the Free Software Foundation, and
> + * may be copied, distributed, and modified under those terms.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * The ROCKCHIP Type-C PHY has two PLL clocks. The first PLL clock
> + * is used for USB3, the second PLL clock is used for DP. This Type-C PHY has
> + * 3 working modes: USB3 only mode, DP only mode, and USB3+DP mode.
> + * At USB3 only mode, both PLL clocks need to be initialized, this allows the
> + * PHY to switch mode between USB3 and USB3+DP, without disconnecting the USB
> + * device.
> + * In The DP only mode, only the DP PLL needs to be powered on, and the 4 lanes
> + * are all used for DP.
> + *
> + * This driver gets extcon cable state and property, then decides which mode to
> + * select:
> + *
> + * 1. USB3 only mode:
> + * EXTCON_USB or EXTCON_USB_HOST state is true, and
> + * EXTCON_PROP_USB_SS property is true.
> + * EXTCON_DISP_DP state is false.
> + *
> + * 2. DP only mode:
> + * EXTCON_DISP_DP state is true, and
> + * EXTCON_PROP_USB_SS property is false.
> + * If EXTCON_USB_HOST state is true, it is DP + USB2 mode, since the USB2 phy
> + * is a separate phy, so this case is still DP only mode.
> + *
> + * 3. USB3+DP mode:
> + * EXTCON_USB_HOST and EXTCON_DISP_DP are both true, and
> + * EXTCON_PROP_USB_SS property is true.
> + *
> + * This Type-C PHY driver supports normal and flip orientation. The orientation
> + * is reported by the EXTCON_PROP_USB_TYPEC_POLARITY property: true is flip
> + * orientation, false is normal orientation.
> + *
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/clk-provider.h>
> +#include <linux/delay.h>
> +#include <linux/extcon.h>
> +#include <linux/io.h>
> +#include <linux/iopoll.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/mutex.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/of_platform.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/reset.h>
> +
> +#include <linux/mfd/syscon.h>
> +#include <linux/phy/phy.h>
> +
> +#define CMN_SSM_BANDGAP (0x21 << 2)
> +#define CMN_SSM_BIAS (0x22 << 2)
> +#define CMN_PLLSM0_PLLEN (0x29 << 2)
> +#define CMN_PLLSM0_PLLPRE (0x2a << 2)
> +#define CMN_PLLSM0_PLLVREF (0x2b << 2)
> +#define CMN_PLLSM0_PLLLOCK (0x2c << 2)
> +#define CMN_PLLSM1_PLLEN (0x31 << 2)
> +#define CMN_PLLSM1_PLLPRE (0x32 << 2)
> +#define CMN_PLLSM1_PLLVREF (0x33 << 2)
> +#define CMN_PLLSM1_PLLLOCK (0x34 << 2)
> +#define CMN_PLLSM1_USER_DEF_CTRL (0x37 << 2)
> +#define CMN_ICAL_OVRD (0xc1 << 2)
> +#define CMN_PLL0_VCOCAL_OVRD (0x83 << 2)
> +#define CMN_PLL0_VCOCAL_INIT (0x84 << 2)
> +#define CMN_PLL0_VCOCAL_ITER (0x85 << 2)
> +#define CMN_PLL0_LOCK_REFCNT_START (0x90 << 2)
> +#define CMN_PLL0_LOCK_PLLCNT_START (0x92 << 2)
> +#define CMN_PLL0_LOCK_PLLCNT_THR (0x93 << 2)
> +#define CMN_PLL0_INTDIV (0x94 << 2)
> +#define CMN_PLL0_FRACDIV (0x95 << 2)
> +#define CMN_PLL0_HIGH_THR (0x96 << 2)
> +#define CMN_PLL0_DSM_DIAG (0x97 << 2)
> +#define CMN_PLL0_SS_CTRL1 (0x98 << 2)
> +#define CMN_PLL0_SS_CTRL2 (0x99 << 2)
> +#define CMN_PLL1_VCOCAL_START (0xa1 << 2)
> +#define CMN_PLL1_VCOCAL_OVRD (0xa3 << 2)
> +#define CMN_PLL1_VCOCAL_INIT (0xa4 << 2)
> +#define CMN_PLL1_VCOCAL_ITER (0xa5 << 2)
> +#define CMN_PLL1_LOCK_REFCNT_START (0xb0 << 2)
> +#define CMN_PLL1_LOCK_PLLCNT_START (0xb2 << 2)
> +#define CMN_PLL1_LOCK_PLLCNT_THR (0xb3 << 2)
> +#define CMN_PLL1_INTDIV (0xb4 << 2)
> +#define CMN_PLL1_FRACDIV (0xb5 << 2)
> +#define CMN_PLL1_HIGH_THR (0xb6 << 2)
> +#define CMN_PLL1_DSM_DIAG (0xb7 << 2)
> +#define CMN_PLL1_SS_CTRL1 (0xb8 << 2)
> +#define CMN_PLL1_SS_CTRL2 (0xb9 << 2)
> +#define CMN_RXCAL_OVRD (0xd1 << 2)
> +#define CMN_TXPUCAL_CTRL (0xe0 << 2)
> +#define CMN_TXPUCAL_OVRD (0xe1 << 2)
> +#define CMN_TXPDCAL_OVRD (0xf1 << 2)
> +#define CMN_DIAG_PLL0_FBH_OVRD (0x1c0 << 2)
> +#define CMN_DIAG_PLL0_FBL_OVRD (0x1c1 << 2)
> +#define CMN_DIAG_PLL0_OVRD (0x1c2 << 2)
> +#define CMN_DIAG_PLL0_V2I_TUNE (0x1c5 << 2)
> +#define CMN_DIAG_PLL0_CP_TUNE (0x1c6 << 2)
> +#define CMN_DIAG_PLL0_LF_PROG (0x1c7 << 2)
> +#define CMN_DIAG_PLL1_FBH_OVRD (0x1d0 << 2)
> +#define CMN_DIAG_PLL1_FBL_OVRD (0x1d1 << 2)
> +#define CMN_DIAG_PLL1_OVRD (0x1d2 << 2)
> +#define CMN_DIAG_PLL1_V2I_TUNE (0x1d5 << 2)
> +#define CMN_DIAG_PLL1_CP_TUNE (0x1d6 << 2)
> +#define CMN_DIAG_PLL1_LF_PROG (0x1d7 << 2)
> +#define CMN_DIAG_PLL1_PTATIS_TUNE1 (0x1d8 << 2)
> +#define CMN_DIAG_PLL1_PTATIS_TUNE2 (0x1d9 << 2)
> +#define CMN_DIAG_PLL1_INCLK_CTRL (0x1da << 2)
> +#define CMN_DIAG_HSCLK_SEL (0x1e0 << 2)
> +
> +#define XCVR_PSM_RCTRL(n) ((0x4001 | ((n) << 9)) << 2)
> +#define XCVR_PSM_CAL_TMR(n) ((0x4002 | ((n) << 9)) << 2)
> +#define XCVR_PSM_A0IN_TMR(n) ((0x4003 | ((n) << 9)) << 2)
> +#define TX_TXCC_CAL_SCLR_MULT(n) ((0x4047 | ((n) << 9)) << 2)
> +#define TX_TXCC_CPOST_MULT_00(n) ((0x404c | ((n) << 9)) << 2)
> +#define TX_TXCC_CPOST_MULT_01(n) ((0x404d | ((n) << 9)) << 2)
> +#define TX_TXCC_CPOST_MULT_10(n) ((0x404e | ((n) << 9)) << 2)
> +#define TX_TXCC_CPOST_MULT_11(n) ((0x404f | ((n) << 9)) << 2)
> +#define TX_TXCC_MGNFS_MULT_000(n) ((0x4050 | ((n) << 9)) << 2)
> +#define TX_TXCC_MGNFS_MULT_001(n) ((0x4051 | ((n) << 9)) << 2)
> +#define TX_TXCC_MGNFS_MULT_010(n) ((0x4052 | ((n) << 9)) << 2)
> +#define TX_TXCC_MGNFS_MULT_011(n) ((0x4053 | ((n) << 9)) << 2)
> +#define TX_TXCC_MGNFS_MULT_100(n) ((0x4054 | ((n) << 9)) << 2)
> +#define TX_TXCC_MGNFS_MULT_101(n) ((0x4055 | ((n) << 9)) << 2)
> +#define TX_TXCC_MGNFS_MULT_110(n) ((0x4056 | ((n) << 9)) << 2)
> +#define TX_TXCC_MGNFS_MULT_111(n) ((0x4057 | ((n) << 9)) << 2)
> +#define XCVR_DIAG_PLLDRC_CTRL(n) ((0x40e0 | ((n) << 9)) << 2)
> +#define XCVR_DIAG_BIDI_CTRL(n) ((0x40e8 | ((n) << 9)) << 2)
> +#define XCVR_DIAG_LANE_FCM_EN_MGN(n) ((0x40f2 | ((n) << 9)) << 2)
> +#define TX_PSC_A0(n) ((0x4100 | ((n) << 9)) << 2)
> +#define TX_PSC_A1(n) ((0x4101 | ((n) << 9)) << 2)
> +#define TX_PSC_A2(n) ((0x4102 | ((n) << 9)) << 2)
> +#define TX_PSC_A3(n) ((0x4103 | ((n) << 9)) << 2)
> +#define TX_RCVDET_CTRL(n) ((0x4120 | ((n) << 9)) << 2)
> +#define TX_RCVDET_EN_TMR(n) ((0x4122 | ((n) << 9)) << 2)
> +#define TX_RCVDET_ST_TMR(n) ((0x4123 | ((n) << 9)) << 2)
> +#define TX_DIAG_TX_DRV(n) ((0x41e1 | ((n) << 9)) << 2)
> +#define TX_DIAG_BGREF_PREDRV_DELAY (0x41e7 << 2)
> +#define TX_ANA_CTRL_REG_1 (0x5020 << 2)
> +#define TX_ANA_CTRL_REG_2 (0x5021 << 2)
> +#define TXDA_COEFF_CALC_CTRL (0x5022 << 2)
> +#define TX_DIG_CTRL_REG_2 (0x5024 << 2)
> +#define TXDA_CYA_AUXDA_CYA (0x5025 << 2)
> +#define TX_ANA_CTRL_REG_3 (0x5026 << 2)
> +#define TX_ANA_CTRL_REG_4 (0x5027 << 2)
> +#define TX_ANA_CTRL_REG_5 (0x5029 << 2)
> +
> +#define RX_PSC_A0(n) ((0x8000 | ((n) << 9)) << 2)
> +#define RX_PSC_A1(n) ((0x8001 | ((n) << 9)) << 2)
> +#define RX_PSC_A2(n) ((0x8002 | ((n) << 9)) << 2)
> +#define RX_PSC_A3(n) ((0x8003 | ((n) << 9)) << 2)
> +#define RX_PSC_CAL(n) ((0x8006 | ((n) << 9)) << 2)
> +#define RX_PSC_RDY(n) ((0x8007 | ((n) << 9)) << 2)
> +#define RX_IQPI_ILL_CAL_OVRD (0x8023 << 2)
> +#define RX_EPI_ILL_CAL_OVRD (0x8033 << 2)
> +#define RX_SDCAL0_OVRD (0x8041 << 2)
> +#define RX_SDCAL1_OVRD (0x8049 << 2)
> +#define RX_SLC_INIT (0x806d << 2)
> +#define RX_SLC_RUN (0x806e << 2)
> +#define RX_CDRLF_CNFG2 (0x8081 << 2)
> +#define RX_SIGDET_HL_FILT_TMR(n) ((0x8090 | ((n) << 9)) << 2)
> +#define RX_SLC_IOP0_OVRD (0x8101 << 2)
> +#define RX_SLC_IOP1_OVRD (0x8105 << 2)
> +#define RX_SLC_QOP0_OVRD (0x8109 << 2)
> +#define RX_SLC_QOP1_OVRD (0x810d << 2)
> +#define RX_SLC_EOP0_OVRD (0x8111 << 2)
> +#define RX_SLC_EOP1_OVRD (0x8115 << 2)
> +#define RX_SLC_ION0_OVRD (0x8119 << 2)
> +#define RX_SLC_ION1_OVRD (0x811d << 2)
> +#define RX_SLC_QON0_OVRD (0x8121 << 2)
> +#define RX_SLC_QON1_OVRD (0x8125 << 2)
> +#define RX_SLC_EON0_OVRD (0x8129 << 2)
> +#define RX_SLC_EON1_OVRD (0x812d << 2)
> +#define RX_SLC_IEP0_OVRD (0x8131 << 2)
> +#define RX_SLC_IEP1_OVRD (0x8135 << 2)
> +#define RX_SLC_QEP0_OVRD (0x8139 << 2)
> +#define RX_SLC_QEP1_OVRD (0x813d << 2)
> +#define RX_SLC_EEP0_OVRD (0x8141 << 2)
> +#define RX_SLC_EEP1_OVRD (0x8145 << 2)
> +#define RX_SLC_IEN0_OVRD (0x8149 << 2)
> +#define RX_SLC_IEN1_OVRD (0x814d << 2)
> +#define RX_SLC_QEN0_OVRD (0x8151 << 2)
> +#define RX_SLC_QEN1_OVRD (0x8155 << 2)
> +#define RX_SLC_EEN0_OVRD (0x8159 << 2)
> +#define RX_SLC_EEN1_OVRD (0x815d << 2)
> +#define RX_REE_CTRL_DATA_MASK(n) ((0x81bb | ((n) << 9)) << 2)
> +#define RX_DIAG_SIGDET_TUNE(n) ((0x81dc | ((n) << 9)) << 2)
> +#define RX_DIAG_SC2C_DELAY (0x81e1 << 2)
> +
> +#define PMA_LANE_CFG (0xc000 << 2)
> +#define PIPE_CMN_CTRL1 (0xc001 << 2)
> +#define PIPE_CMN_CTRL2 (0xc002 << 2)
> +#define PIPE_COM_LOCK_CFG1 (0xc003 << 2)
> +#define PIPE_COM_LOCK_CFG2 (0xc004 << 2)
> +#define PIPE_RCV_DET_INH (0xc005 << 2)
> +#define DP_MODE_CTL (0xc008 << 2)
> +#define DP_CLK_CTL (0xc009 << 2)
> +#define STS (0xc00F << 2)
> +#define PHY_ISO_CMN_CTRL (0xc010 << 2)
> +#define PHY_DP_TX_CTL (0xc408 << 2)
> +#define PMA_CMN_CTRL1 (0xc800 << 2)
> +#define PHY_PMA_ISO_CMN_CTRL (0xc810 << 2)
> +#define PHY_ISOLATION_CTRL (0xc81f << 2)
> +#define PHY_PMA_ISO_XCVR_CTRL(n) ((0xcc11 | ((n) << 6)) << 2)
> +#define PHY_PMA_ISO_LINK_MODE(n) ((0xcc12 | ((n) << 6)) << 2)
> +#define PHY_PMA_ISO_PWRST_CTRL(n) ((0xcc13 | ((n) << 6)) << 2)
> +#define PHY_PMA_ISO_TX_DATA_LO(n) ((0xcc14 | ((n) << 6)) << 2)
> +#define PHY_PMA_ISO_TX_DATA_HI(n) ((0xcc15 | ((n) << 6)) << 2)
> +#define PHY_PMA_ISO_RX_DATA_LO(n) ((0xcc16 | ((n) << 6)) << 2)
> +#define PHY_PMA_ISO_RX_DATA_HI(n) ((0xcc17 | ((n) << 6)) << 2)
> +#define TX_BIST_CTRL(n) ((0x4140 | ((n) << 9)) << 2)
> +#define TX_BIST_UDDWR(n) ((0x4141 | ((n) << 9)) << 2)
> +
> +/*
> + * Selects which PLL clock will be driven on the analog high speed
> + * clock 0: PLL 0 div 1
> + * clock 1: PLL 1 div 2
> + */
> +#define CLK_PLL_CONFIG 0X30
> +#define CLK_PLL_MASK 0x33
> +
> +#define CMN_READY BIT(0)
> +
> +#define DP_PLL_CLOCK_ENABLE BIT(2)
> +#define DP_PLL_ENABLE BIT(0)
> +#define DP_PLL_DATA_RATE_RBR ((2 << 12) | (4 << 8))
> +#define DP_PLL_DATA_RATE_HBR ((2 << 12) | (4 << 8))
> +#define DP_PLL_DATA_RATE_HBR2 ((1 << 12) | (2 << 8))
> +
> +#define DP_MODE_A0 BIT(4)
> +#define DP_MODE_A2 BIT(6)
> +#define DP_MODE_ENTER_A0 0xc101
> +#define DP_MODE_ENTER_A2 0xc104
> +
> +#define PHY_MODE_SET_TIMEOUT 100000
> +
> +#define PIN_ASSIGN_C_E 0x51d9
> +#define PIN_ASSIGN_D_F 0x5100
> +
> +#define MODE_DISCONNECT 0
> +#define MODE_UFP_USB BIT(0)
> +#define MODE_DFP_USB BIT(1)
> +#define MODE_DFP_DP BIT(2)
> +
> +struct usb3phy_reg {
> + u32 offset;
> + u32 enable_bit;
> + u32 write_enable;
> +};
> +
> +struct rockchip_usb3phy_port_cfg {
> + struct usb3phy_reg typec_conn_dir;
> + struct usb3phy_reg usb3tousb2_en;
> + struct usb3phy_reg external_psm;
> + struct usb3phy_reg pipe_status;
> +};
> +
> +struct rockchip_typec_phy {
> + struct device *dev;
> + void __iomem *base;
> + struct extcon_dev *extcon;
> + struct regmap *grf_regs;
> + struct clk *clk_core;
> + struct clk *clk_ref;
> + struct reset_control *uphy_rst;
> + struct reset_control *pipe_rst;
> + struct reset_control *tcphy_rst;
> + struct rockchip_usb3phy_port_cfg port_cfgs;
> + /* mutex to protect access to individual PHYs */
> + struct mutex lock;
> +
> + bool flip;
> + u8 mode;
> +};
> +
> +struct phy_reg {
> + u16 value;
> + u32 addr;
> +};
> +
> +struct phy_reg usb3_pll_cfg[] = {
> + { 0xf0, CMN_PLL0_VCOCAL_INIT },
> + { 0x18, CMN_PLL0_VCOCAL_ITER },
> + { 0xd0, CMN_PLL0_INTDIV },
> + { 0x4a4a, CMN_PLL0_FRACDIV },
> + { 0x34, CMN_PLL0_HIGH_THR },
> + { 0x1ee, CMN_PLL0_SS_CTRL1 },
> + { 0x7f03, CMN_PLL0_SS_CTRL2 },
> + { 0x20, CMN_PLL0_DSM_DIAG },
> + { 0, CMN_DIAG_PLL0_OVRD },
> + { 0, CMN_DIAG_PLL0_FBH_OVRD },
> + { 0, CMN_DIAG_PLL0_FBL_OVRD },
> + { 0x7, CMN_DIAG_PLL0_V2I_TUNE },
> + { 0x45, CMN_DIAG_PLL0_CP_TUNE },
> + { 0x8, CMN_DIAG_PLL0_LF_PROG },
> +};
> +
> +struct phy_reg dp_pll_cfg[] = {
> + { 0xf0, CMN_PLL1_VCOCAL_INIT },
> + { 0x18, CMN_PLL1_VCOCAL_ITER },
> + { 0x30b9, CMN_PLL1_VCOCAL_START },
> + { 0x21c, CMN_PLL1_INTDIV },
> + { 0, CMN_PLL1_FRACDIV },
> + { 0x5, CMN_PLL1_HIGH_THR },
> + { 0x35, CMN_PLL1_SS_CTRL1 },
> + { 0x7f1e, CMN_PLL1_SS_CTRL2 },
> + { 0x20, CMN_PLL1_DSM_DIAG },
> + { 0, CMN_PLLSM1_USER_DEF_CTRL },
> + { 0, CMN_DIAG_PLL1_OVRD },
> + { 0, CMN_DIAG_PLL1_FBH_OVRD },
> + { 0, CMN_DIAG_PLL1_FBL_OVRD },
> + { 0x6, CMN_DIAG_PLL1_V2I_TUNE },
> + { 0x45, CMN_DIAG_PLL1_CP_TUNE },
> + { 0x8, CMN_DIAG_PLL1_LF_PROG },
> + { 0x100, CMN_DIAG_PLL1_PTATIS_TUNE1 },
> + { 0x7, CMN_DIAG_PLL1_PTATIS_TUNE2 },
> + { 0x4, CMN_DIAG_PLL1_INCLK_CTRL },
> +};
> +
> +static void tcphy_cfg_24m(struct rockchip_typec_phy *tcphy)
> +{
> + u32 i, rdata;
> +
> + /*
> + * cmn_ref_clk_sel = 3, select the 24Mhz for clk parent
> + * cmn_psm_clk_dig_div = 2, set the clk division to 2
> + */
> + writel(0x830, tcphy->base + PMA_CMN_CTRL1);
> + for (i = 0; i < 4; i++) {
> + /*
> + * The following PHY configuration assumes a 24 MHz reference
> + * clock.
> + */
> + writel(0x90, tcphy->base + XCVR_DIAG_LANE_FCM_EN_MGN(i));
> + writel(0x960, tcphy->base + TX_RCVDET_EN_TMR(i));
> + writel(0x30, tcphy->base + TX_RCVDET_ST_TMR(i));
> + }
> +
> + rdata = readl(tcphy->base + CMN_DIAG_HSCLK_SEL);
> + rdata &= ~CLK_PLL_MASK;
> + rdata |= CLK_PLL_CONFIG;
> + writel(rdata, tcphy->base + CMN_DIAG_HSCLK_SEL);
> +}
> +
> +static void tcphy_cfg_usb3_pll(struct rockchip_typec_phy *tcphy)
> +{
> + u32 i;
> +
> + /* load the configuration of PLL0 */
> + for (i = 0; i < ARRAY_SIZE(usb3_pll_cfg); i++)
> + writel(usb3_pll_cfg[i].value,
> + tcphy->base + usb3_pll_cfg[i].addr);
> +}
> +
> +static void tcphy_cfg_dp_pll(struct rockchip_typec_phy *tcphy)
> +{
> + u32 i;
> +
> + /* set the default mode to RBR */
> + writel(DP_PLL_CLOCK_ENABLE | DP_PLL_ENABLE | DP_PLL_DATA_RATE_RBR,
> + tcphy->base + DP_CLK_CTL);
> +
> + /* load the configuration of PLL1 */
> + for (i = 0; i < ARRAY_SIZE(dp_pll_cfg); i++)
> + writel(dp_pll_cfg[i].value, tcphy->base + dp_pll_cfg[i].addr);
> +}
> +
> +static void tcphy_tx_usb3_cfg_lane(struct rockchip_typec_phy *tcphy, u32 lane)
> +{
> + writel(0x7799, tcphy->base + TX_PSC_A0(lane));
> + writel(0x7798, tcphy->base + TX_PSC_A1(lane));
> + writel(0x5098, tcphy->base + TX_PSC_A2(lane));
> + writel(0x5098, tcphy->base + TX_PSC_A3(lane));
> + writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_000(lane));
> + writel(0xbf, tcphy->base + XCVR_DIAG_BIDI_CTRL(lane));
> +}
> +
> +static void tcphy_rx_usb3_cfg_lane(struct rockchip_typec_phy *tcphy, u32 lane)
> +{
> + writel(0xa6fd, tcphy->base + RX_PSC_A0(lane));
> + writel(0xa6fd, tcphy->base + RX_PSC_A1(lane));
> + writel(0xa410, tcphy->base + RX_PSC_A2(lane));
> + writel(0x2410, tcphy->base + RX_PSC_A3(lane));
> + writel(0x23ff, tcphy->base + RX_PSC_CAL(lane));
> + writel(0x13, tcphy->base + RX_SIGDET_HL_FILT_TMR(lane));
> + writel(0x03e7, tcphy->base + RX_REE_CTRL_DATA_MASK(lane));
> + writel(0x1004, tcphy->base + RX_DIAG_SIGDET_TUNE(lane));
> + writel(0x2010, tcphy->base + RX_PSC_RDY(lane));
> + writel(0xfb, tcphy->base + XCVR_DIAG_BIDI_CTRL(lane));
> +}
> +
> +static void tcphy_dp_cfg_lane(struct rockchip_typec_phy *tcphy, u32 lane)
> +{
> + u16 rdata;
> +
> + writel(0xbefc, tcphy->base + XCVR_PSM_RCTRL(lane));
> + writel(0x6799, tcphy->base + TX_PSC_A0(lane));
> + writel(0x6798, tcphy->base + TX_PSC_A1(lane));
> + writel(0x98, tcphy->base + TX_PSC_A2(lane));
> + writel(0x98, tcphy->base + TX_PSC_A3(lane));
> +
> + writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_000(lane));
> + writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_001(lane));
> + writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_010(lane));
> + writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_011(lane));
> + writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_100(lane));
> + writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_101(lane));
> + writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_110(lane));
> + writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_111(lane));
> + writel(0, tcphy->base + TX_TXCC_CPOST_MULT_10(lane));
> + writel(0, tcphy->base + TX_TXCC_CPOST_MULT_01(lane));
> + writel(0, tcphy->base + TX_TXCC_CPOST_MULT_00(lane));
> + writel(0, tcphy->base + TX_TXCC_CPOST_MULT_11(lane));
> +
> + writel(0x128, tcphy->base + TX_TXCC_CAL_SCLR_MULT(lane));
> + writel(0x400, tcphy->base + TX_DIAG_TX_DRV(lane));
> +
> + rdata = readl(tcphy->base + XCVR_DIAG_PLLDRC_CTRL(lane));
> + rdata = (rdata & 0x8fff) | 0x6000;
> + writel(rdata, tcphy->base + XCVR_DIAG_PLLDRC_CTRL(lane));
> +}
> +
> +static inline int property_enable(struct rockchip_typec_phy *tcphy,
> + const struct usb3phy_reg *reg, bool en)
> +{
> + u32 mask = 1 << reg->write_enable;
> + u32 val = en << reg->enable_bit;
> +
> + return regmap_write(tcphy->grf_regs, reg->offset, val | mask);
> +}
> +
> +static void tcphy_dp_aux_calibration(struct rockchip_typec_phy *tcphy)
> +{
> + u16 rdata, rdata2, val;
> +
> + /* disable txda_cal_latch_en for rewrite the calibration values */
> + rdata = readl(tcphy->base + TX_ANA_CTRL_REG_1);
> + val = rdata & 0xdfff;
> + writel(val, tcphy->base + TX_ANA_CTRL_REG_1);
> +
> + /*
> + * read a resistor calibration code from CMN_TXPUCAL_CTRL[6:0] and
> + * write it to TX_DIG_CTRL_REG_2[6:0], and delay 1ms to make sure it
> + * works.
> + */
> + rdata = readl(tcphy->base + TX_DIG_CTRL_REG_2);
> + rdata = rdata & 0xffc0;
> +
> + rdata2 = readl(tcphy->base + CMN_TXPUCAL_CTRL);
> + rdata2 = rdata2 & 0x3f;
> +
> + val = rdata | rdata2;
> + writel(val, tcphy->base + TX_DIG_CTRL_REG_2);
> + usleep_range(1000, 1050);
> +
> + /*
> + * Enable signal for latch that sample and holds calibration values.
> + * Activate this signal for 1 clock cycle to sample new calibration
> + * values.
> + */
> + rdata = readl(tcphy->base + TX_ANA_CTRL_REG_1);
> + val = rdata | 0x2000;
> + writel(val, tcphy->base + TX_ANA_CTRL_REG_1);
> + usleep_range(150, 200);
> +
> + /* set TX Voltage Level and TX Deemphasis to 0 */
> + writel(0, tcphy->base + PHY_DP_TX_CTL);
> + /* re-enable decap */
> + writel(0x100, tcphy->base + TX_ANA_CTRL_REG_2);
> + writel(0x300, tcphy->base + TX_ANA_CTRL_REG_2);
> + writel(0x2008, tcphy->base + TX_ANA_CTRL_REG_1);
> + writel(0x2018, tcphy->base + TX_ANA_CTRL_REG_1);
> +
> + writel(0, tcphy->base + TX_ANA_CTRL_REG_5);
> +
> + /*
> + * Programs txda_drv_ldo_prog[15:0], Sets driver LDO
> + * voltage 16'h1001 for DP-AUX-TX and RX
> + */
> + writel(0x1001, tcphy->base + TX_ANA_CTRL_REG_4);
> +
> + /* re-enables Bandgap reference for LDO */
> + writel(0x2098, tcphy->base + TX_ANA_CTRL_REG_1);
> + writel(0x2198, tcphy->base + TX_ANA_CTRL_REG_1);
> +
> + /*
> + * re-enables the transmitter pre-driver, driver data selection MUX,
> + * and receiver detect circuits.
> + */
> + writel(0x301, tcphy->base + TX_ANA_CTRL_REG_2);
> + writel(0x303, tcphy->base + TX_ANA_CTRL_REG_2);
> +
> + /*
> + * BIT 12: Controls auxda_polarity, which selects the polarity of the
> + * xcvr:
> + * 1, Reverses the polarity (If TYPEC, Pulls ups aux_p and pull
> + * down aux_m)
> + * 0, Normal polarity (if TYPE_C, pulls up aux_m and pulls down
> + * aux_p)
> + */
> + val = 0xa078;
> + if (!tcphy->flip)
> + val |= BIT(12);
> + writel(val, tcphy->base + TX_ANA_CTRL_REG_1);
> +
> + writel(0, tcphy->base + TX_ANA_CTRL_REG_3);
> + writel(0, tcphy->base + TX_ANA_CTRL_REG_4);
> + writel(0, tcphy->base + TX_ANA_CTRL_REG_5);
> +
> + /*
> + * Controls low_power_swing_en, set the voltage swing of the driver
> + * to 400mv. The values below are peak to peak (differential) values.
> + */
> + writel(4, tcphy->base + TXDA_COEFF_CALC_CTRL);
> + writel(0, tcphy->base + TXDA_CYA_AUXDA_CYA);
> +
> + /* Controls tx_high_z_tm_en */
> + val = readl(tcphy->base + TX_DIG_CTRL_REG_2);
> + val |= BIT(15);
> + writel(val, tcphy->base + TX_DIG_CTRL_REG_2);
> +}
> +
> +static int tcphy_phy_init(struct rockchip_typec_phy *tcphy, u8 mode)
> +{
> + struct rockchip_usb3phy_port_cfg *cfg = &tcphy->port_cfgs;
> + int ret, i;
> + u32 val;
> +
> + ret = clk_prepare_enable(tcphy->clk_core);
> + if (ret) {
> + dev_err(tcphy->dev, "Failed to prepare_enable core clock\n");
> + return ret;
> + }
> +
> + ret = clk_prepare_enable(tcphy->clk_ref);
> + if (ret) {
> + dev_err(tcphy->dev, "Failed to prepare_enable ref clock\n");
> + goto err_clk_core;
> + }
> +
> + reset_control_deassert(tcphy->tcphy_rst);
> +
> + property_enable(tcphy, &cfg->typec_conn_dir, tcphy->flip);
> +
> + tcphy_cfg_24m(tcphy);
> +
> + if (mode == MODE_DFP_DP) {
> + tcphy_cfg_dp_pll(tcphy);
> + for (i = 0; i < 4; i++)
> + tcphy_dp_cfg_lane(tcphy, i);
> +
> + writel(PIN_ASSIGN_C_E, tcphy->base + PMA_LANE_CFG);
> + } else {
> + tcphy_cfg_usb3_pll(tcphy);
> + tcphy_cfg_dp_pll(tcphy);
> + if (tcphy->flip) {
> + tcphy_tx_usb3_cfg_lane(tcphy, 3);
> + tcphy_rx_usb3_cfg_lane(tcphy, 2);
> + tcphy_dp_cfg_lane(tcphy, 0);
> + tcphy_dp_cfg_lane(tcphy, 1);
> + } else {
> + tcphy_tx_usb3_cfg_lane(tcphy, 0);
> + tcphy_rx_usb3_cfg_lane(tcphy, 1);
> + tcphy_dp_cfg_lane(tcphy, 2);
> + tcphy_dp_cfg_lane(tcphy, 3);
> + }
> +
> + writel(PIN_ASSIGN_D_F, tcphy->base + PMA_LANE_CFG);
> + }
> +
> + writel(DP_MODE_ENTER_A2, tcphy->base + DP_MODE_CTL);
> +
> + reset_control_deassert(tcphy->uphy_rst);
> +
> + ret = readx_poll_timeout(readl, tcphy->base + PMA_CMN_CTRL1,
> + val, val & CMN_READY, 10,
> + PHY_MODE_SET_TIMEOUT);
> + if (ret < 0) {
> + dev_err(tcphy->dev, "wait pma ready timeout\n");
> + ret = -ETIMEDOUT;
> + goto err_wait_pma;
> + }
> +
> + reset_control_deassert(tcphy->pipe_rst);
> +
> + return 0;
> +
> +err_wait_pma:
> + reset_control_assert(tcphy->uphy_rst);
> + reset_control_assert(tcphy->tcphy_rst);
> + clk_disable_unprepare(tcphy->clk_ref);
> +err_clk_core:
> + clk_disable_unprepare(tcphy->clk_core);
> + return ret;
> +}
> +
> +static void tcphy_phy_deinit(struct rockchip_typec_phy *tcphy)
> +{
> + reset_control_assert(tcphy->tcphy_rst);
> + reset_control_assert(tcphy->uphy_rst);
> + reset_control_assert(tcphy->pipe_rst);
> + clk_disable_unprepare(tcphy->clk_core);
> + clk_disable_unprepare(tcphy->clk_ref);
> +}
> +
> +static int tcphy_get_mode(struct rockchip_typec_phy *tcphy)
> +{
> + struct extcon_dev *edev = tcphy->extcon;
> + union extcon_property_value property;
> + unsigned int id;
> + bool dfp, ufp, dp;
> + u8 mode;
> + int ret;
> +
> + ufp = extcon_get_state(edev, EXTCON_USB);
> + dfp = extcon_get_state(edev, EXTCON_USB_HOST);
> + dp = extcon_get_state(edev, EXTCON_DISP_DP);
> +
> + mode = MODE_DFP_USB;
> + id = EXTCON_USB_HOST;
> +
> + if (ufp) {
> + mode = MODE_UFP_USB;
> + id = EXTCON_USB;
> + } else if (dp) {
> + mode = MODE_DFP_DP;
> + id = EXTCON_DISP_DP;
> +
> + ret = extcon_get_property(edev, id, EXTCON_PROP_USB_SS,
> + &property);
> + if (ret) {
> + dev_err(tcphy->dev, "get superspeed property failed\n");
> + return ret;
> + }
> +
> + if (property.intval)
> + mode |= MODE_DFP_USB;
> + }
> +
> + ret = extcon_get_property(edev, id, EXTCON_PROP_USB_TYPEC_POLARITY,
> + &property);
> + if (ret) {
> + dev_err(tcphy->dev, "get polarity property failed\n");
> + return ret;
> + }
> +
> + tcphy->flip = property.intval ? 1 : 0;
> +
> + return mode;
> +}
> +
> +static int rockchip_usb3_phy_power_on(struct phy *phy)
> +{
> + struct rockchip_typec_phy *tcphy = phy_get_drvdata(phy);
> + struct rockchip_usb3phy_port_cfg *cfg = &tcphy->port_cfgs;
> + const struct usb3phy_reg *reg = &cfg->pipe_status;
> + int timeout, new_mode, ret = 0;
> + u32 val;
> +
> + mutex_lock(&tcphy->lock);
> +
> + new_mode = tcphy_get_mode(tcphy);
> + if (new_mode < 0) {
> + ret = new_mode;
> + goto unlock_ret;
> + }
> +
> + /* DP-only mode; fall back to USB2 */
> + if (!(new_mode & (MODE_DFP_USB | MODE_UFP_USB)))
> + goto unlock_ret;
> +
> + if (tcphy->mode == new_mode)
> + goto unlock_ret;
> +
> + if (tcphy->mode == MODE_DISCONNECT)
> + tcphy_phy_init(tcphy, new_mode);
> +
> + /* wait TCPHY for pipe ready */
> + for (timeout = 0; timeout < 100; timeout++) {
> + regmap_read(tcphy->grf_regs, reg->offset, &val);
> + if (!(val & BIT(reg->enable_bit))) {
> + tcphy->mode |= new_mode & (MODE_DFP_USB | MODE_UFP_USB);
> + goto unlock_ret;
> + }
> + usleep_range(10, 20);
> + }
> +
> + if (tcphy->mode == MODE_DISCONNECT)
> + tcphy_phy_deinit(tcphy);
> +
> + ret = -ETIMEDOUT;
> +
> +unlock_ret:
> + mutex_unlock(&tcphy->lock);
> + return ret;
> +}
> +
> +static int rockchip_usb3_phy_power_off(struct phy *phy)
> +{
> + struct rockchip_typec_phy *tcphy = phy_get_drvdata(phy);
> +
> + mutex_lock(&tcphy->lock);
> +
> + if (tcphy->mode == MODE_DISCONNECT)
> + goto unlock;
> +
> + tcphy->mode &= ~(MODE_UFP_USB | MODE_DFP_USB);
> + if (tcphy->mode == MODE_DISCONNECT)
> + tcphy_phy_deinit(tcphy);
> +
> +unlock:
> + mutex_unlock(&tcphy->lock);
> + return 0;
> +}
> +
> +static const struct phy_ops rockchip_usb3_phy_ops = {
> + .power_on = rockchip_usb3_phy_power_on,
> + .power_off = rockchip_usb3_phy_power_off,
> + .owner = THIS_MODULE,
> +};
> +
> +static int rockchip_dp_phy_power_on(struct phy *phy)
> +{
> + struct rockchip_typec_phy *tcphy = phy_get_drvdata(phy);
> + int new_mode, ret = 0;
> + u32 val;
> +
> + mutex_lock(&tcphy->lock);
> +
> + new_mode = tcphy_get_mode(tcphy);
> + if (new_mode < 0) {
> + ret = new_mode;
> + goto unlock_ret;
> + }
> +
> + if (!(new_mode & MODE_DFP_DP)) {
> + ret = -ENODEV;
> + goto unlock_ret;
> + }
> +
> + if (tcphy->mode == new_mode)
> + goto unlock_ret;
> +
> + /*
> + * If the PHY has been power on, but the mode is not DP only mode,
> + * re-init the PHY for setting all of 4 lanes to DP.
> + */
> + if (new_mode == MODE_DFP_DP && tcphy->mode != MODE_DISCONNECT) {
> + tcphy_phy_deinit(tcphy);
> + tcphy_phy_init(tcphy, new_mode);
> + } else if (tcphy->mode == MODE_DISCONNECT) {
> + tcphy_phy_init(tcphy, new_mode);
> + }
> +
> + ret = readx_poll_timeout(readl, tcphy->base + DP_MODE_CTL,
> + val, val & DP_MODE_A2, 1000,
> + PHY_MODE_SET_TIMEOUT);
> + if (ret < 0) {
> + dev_err(tcphy->dev, "failed to wait TCPHY enter A2\n");
> + goto power_on_finish;
> + }
> +
> + tcphy_dp_aux_calibration(tcphy);
> +
> + writel(DP_MODE_ENTER_A0, tcphy->base + DP_MODE_CTL);
> +
> + ret = readx_poll_timeout(readl, tcphy->base + DP_MODE_CTL,
> + val, val & DP_MODE_A0, 1000,
> + PHY_MODE_SET_TIMEOUT);
> + if (ret < 0) {
> + writel(DP_MODE_ENTER_A2, tcphy->base + DP_MODE_CTL);
> + dev_err(tcphy->dev, "failed to wait TCPHY enter A0\n");
> + goto power_on_finish;
> + }
> +
> + tcphy->mode |= MODE_DFP_DP;
> +
> +power_on_finish:
> + if (tcphy->mode == MODE_DISCONNECT)
> + tcphy_phy_deinit(tcphy);
> +unlock_ret:
> + mutex_unlock(&tcphy->lock);
> + return ret;
> +}
> +
> +static int rockchip_dp_phy_power_off(struct phy *phy)
> +{
> + struct rockchip_typec_phy *tcphy = phy_get_drvdata(phy);
> +
> + mutex_lock(&tcphy->lock);
> +
> + if (tcphy->mode == MODE_DISCONNECT)
> + goto unlock;
> +
> + tcphy->mode &= ~MODE_DFP_DP;
> +
> + writel(DP_MODE_ENTER_A2, tcphy->base + DP_MODE_CTL);
> +
> + if (tcphy->mode == MODE_DISCONNECT)
> + tcphy_phy_deinit(tcphy);
> +
> +unlock:
> + mutex_unlock(&tcphy->lock);
> + return 0;
> +}
> +
> +static const struct phy_ops rockchip_dp_phy_ops = {
> + .power_on = rockchip_dp_phy_power_on,
> + .power_off = rockchip_dp_phy_power_off,
> + .owner = THIS_MODULE,
> +};
> +
> +static int tcphy_get_param(struct device *dev,
> + struct usb3phy_reg *reg,
> + const char *name)
> +{
> + u32 buffer[3];
> + int ret;
> +
> + ret = of_property_read_u32_array(dev->of_node, name, buffer, 3);
> + if (ret) {
> + dev_err(dev, "Can not parse %s\n", name);
> + return ret;
> + }
> +
> + reg->offset = buffer[0];
> + reg->enable_bit = buffer[1];
> + reg->write_enable = buffer[2];
> + return 0;
> +}
> +
> +static int tcphy_parse_dt(struct rockchip_typec_phy *tcphy,
> + struct device *dev)
> +{
> + struct rockchip_usb3phy_port_cfg *cfg = &tcphy->port_cfgs;
> + int ret;
> +
> + ret = tcphy_get_param(dev, &cfg->typec_conn_dir,
> + "rockchip,typec-conn-dir");
> + if (ret)
> + return ret;
> +
> + ret = tcphy_get_param(dev, &cfg->usb3tousb2_en,
> + "rockchip,usb3tousb2-en");
> + if (ret)
> + return ret;
> +
> + ret = tcphy_get_param(dev, &cfg->external_psm,
> + "rockchip,external-psm");
> + if (ret)
> + return ret;
> +
> + ret = tcphy_get_param(dev, &cfg->pipe_status,
> + "rockchip,pipe-status");
> + if (ret)
> + return ret;
> +
> + tcphy->grf_regs = syscon_regmap_lookup_by_phandle(dev->of_node,
> + "rockchip,grf");
> + if (IS_ERR(tcphy->grf_regs)) {
> + dev_err(dev, "could not find grf dt node\n");
> + return PTR_ERR(tcphy->grf_regs);
> + }
> +
> + tcphy->clk_core = devm_clk_get(dev, "tcpdcore");
> + if (IS_ERR(tcphy->clk_core)) {
> + dev_err(dev, "could not get uphy core clock\n");
> + return PTR_ERR(tcphy->clk_core);
> + }
> +
> + tcphy->clk_ref = devm_clk_get(dev, "tcpdphy-ref");
> + if (IS_ERR(tcphy->clk_ref)) {
> + dev_err(dev, "could not get uphy ref clock\n");
> + return PTR_ERR(tcphy->clk_ref);
> + }
> +
> + tcphy->uphy_rst = devm_reset_control_get(dev, "uphy");
> + if (IS_ERR(tcphy->uphy_rst)) {
> + dev_err(dev, "no uphy_rst reset control found\n");
> + return PTR_ERR(tcphy->uphy_rst);
> + }
> +
> + tcphy->pipe_rst = devm_reset_control_get(dev, "uphy-pipe");
> + if (IS_ERR(tcphy->pipe_rst)) {
> + dev_err(dev, "no pipe_rst reset control found\n");
> + return PTR_ERR(tcphy->pipe_rst);
> + }
> +
> + tcphy->tcphy_rst = devm_reset_control_get(dev, "uphy-tcphy");
> + if (IS_ERR(tcphy->tcphy_rst)) {
> + dev_err(dev, "no tcphy_rst reset control found\n");
> + return PTR_ERR(tcphy->tcphy_rst);
> + }
> +
> + return 0;
> +}
> +
> +static void typec_phy_pre_init(struct rockchip_typec_phy *tcphy)
> +{
> + struct rockchip_usb3phy_port_cfg *cfg = &tcphy->port_cfgs;
> +
> + reset_control_assert(tcphy->tcphy_rst);
> + reset_control_assert(tcphy->uphy_rst);
> + reset_control_assert(tcphy->pipe_rst);
> +
> + /* select external psm clock */
> + property_enable(tcphy, &cfg->external_psm, 1);
> + property_enable(tcphy, &cfg->usb3tousb2_en, 0);
> +
> + tcphy->mode = MODE_DISCONNECT;
> +}
> +
> +static int rockchip_typec_phy_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct device_node *np = dev->of_node;
> + struct device_node *child_np;
> + struct rockchip_typec_phy *tcphy;
> + struct phy_provider *phy_provider;
> + struct resource *res;
> + int ret;
> +
> + tcphy = devm_kzalloc(dev, sizeof(*tcphy), GFP_KERNEL);
> + if (!tcphy)
> + return -ENOMEM;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + tcphy->base = devm_ioremap_resource(dev, res);
> + if (IS_ERR(tcphy->base))
> + return PTR_ERR(tcphy->base);
> +
> + ret = tcphy_parse_dt(tcphy, dev);
> + if (ret)
> + return ret;
> +
> + tcphy->dev = dev;
> + platform_set_drvdata(pdev, tcphy);
> + mutex_init(&tcphy->lock);
> +
> + typec_phy_pre_init(tcphy);
> +
> + tcphy->extcon = extcon_get_edev_by_phandle(dev, 0);
> + if (IS_ERR(tcphy->extcon)) {
> + if (PTR_ERR(tcphy->extcon) != -EPROBE_DEFER)
> + dev_err(dev, "Invalid or missing extcon\n");
> + return PTR_ERR(tcphy->extcon);
> + }
> +
> + for_each_available_child_of_node(np, child_np) {
> + struct phy *phy;
> +
> + if (!of_node_cmp(child_np->name, "dp-port"))
> + phy = devm_phy_create(dev, child_np,
> + &rockchip_dp_phy_ops);
> + else if (!of_node_cmp(child_np->name, "usb3-port"))
> + phy = devm_phy_create(dev, child_np,
> + &rockchip_usb3_phy_ops);
> + else
> + continue;
> +
> + if (IS_ERR(phy)) {
> + dev_err(dev, "failed to create phy: %s\n",
> + child_np->name);
> + return PTR_ERR(phy);
> + }
> +
> + phy_set_drvdata(phy, tcphy);
> + }
> +
> + phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> + if (IS_ERR(phy_provider)) {
> + dev_err(dev, "Failed to register phy provider\n");
> + return PTR_ERR(phy_provider);
> + }
> +
> + return 0;
> +}
> +
> +static const struct of_device_id rockchip_typec_phy_dt_ids[] = {
> + { .compatible = "rockchip,rk3399-typec-phy" },
> + {}
> +};
> +
> +MODULE_DEVICE_TABLE(of, rockchip_typec_phy_dt_ids);
> +
> +static struct platform_driver rockchip_typec_phy_driver = {
> + .probe = rockchip_typec_phy_probe,
> + .driver = {
> + .name = "rockchip-typec-phy",
> + .of_match_table = rockchip_typec_phy_dt_ids,
> + },
> +};
> +
> +module_platform_driver(rockchip_typec_phy_driver);
> +
> +MODULE_AUTHOR("Chris Zhong <zyw at rock-chips.com>");
> +MODULE_AUTHOR("Kever Yang <kever.yang at rock-chips.com>");
> +MODULE_DESCRIPTION("Rockchip USB TYPE-C PHY driver");
> +MODULE_LICENSE("GPL v2");
>
More information about the linux-arm-kernel
mailing list