[PATCH 6/8 v2] arm: orion5x: Add DT-based support for Netgear WNR854T
Jamie Lentin
jm at lentin.co.uk
Mon Sep 5 14:07:26 PDT 2016
This is a router based on the mv88f5181 chipset.
http://www.netgear.com/support/product/WNR854T.aspx
http://wiki.openwrt.org/toh/netgear/wnr854t
Signed-off-by: Jamie Lentin <jm at lentin.co.uk>
---
This removes the contentious vendor partitioning scheme and goes back
to the original partitioning scheme used in non-DT ports to this board.
Using the same partitioning scheme should mean less surprises for
someone trying to upgrade their router.
The non-DT PCI setup is still here, as there are other orion5x DT boards
doing very similar things, and can all be converted at the same time.
The patchset in it's entirety is available at
https://github.com/lentinj/linux wnr854t-support-v2
Cheers,
---
.../bindings/arm/marvell/marvell,orion5x.txt | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/orion5x-netgear-wnr854t.dts | 197 +++++++++++++++++++++
arch/arm/mach-orion5x/Kconfig | 6 +
arch/arm/mach-orion5x/Makefile | 1 +
arch/arm/mach-orion5x/board-wnr854t.c | 78 ++++++++
6 files changed, 284 insertions(+)
create mode 100644 arch/arm/boot/dts/orion5x-netgear-wnr854t.dts
create mode 100644 arch/arm/mach-orion5x/board-wnr854t.c
diff --git a/Documentation/devicetree/bindings/arm/marvell/marvell,orion5x.txt b/Documentation/devicetree/bindings/arm/marvell/marvell,orion5x.txt
index ff3c120..748a8f2 100644
--- a/Documentation/devicetree/bindings/arm/marvell/marvell,orion5x.txt
+++ b/Documentation/devicetree/bindings/arm/marvell/marvell,orion5x.txt
@@ -22,3 +22,4 @@ board. Currently known boards are:
"lacie,d2-network"
"marvell,rd-88f5182-nas"
"maxtor,shared-storage-2"
+"netgear,wnr854t"
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index faacd52..4588b3c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -584,6 +584,7 @@ dtb-$(CONFIG_ARCH_ORION5X) += \
orion5x-linkstation-lswtgl.dtb \
orion5x-lswsgl.dtb \
orion5x-maxtor-shared-storage-2.dtb \
+ orion5x-netgear-wnr854t.dtb \
orion5x-rd88f5182-nas.dtb
dtb-$(CONFIG_ARCH_PRIMA2) += \
prima2-evb.dtb
diff --git a/arch/arm/boot/dts/orion5x-netgear-wnr854t.dts b/arch/arm/boot/dts/orion5x-netgear-wnr854t.dts
new file mode 100644
index 0000000..cce5091
--- /dev/null
+++ b/arch/arm/boot/dts/orion5x-netgear-wnr854t.dts
@@ -0,0 +1,197 @@
+/*
+ * Copyright (C) 2016 Jamie Lentin <jm at lentin.co.uk>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "orion5x-mv88f5181.dtsi"
+
+/ {
+ model = "Netgear WNR854-t";
+ compatible = "netgear,wnr854t", "marvell,orion5x-88f5181",
+ "marvell,orion5x";
+
+ memory {
+ reg = <0x00000000 0x2000000>; /* 32 MB */
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>,
+ <MBUS_ID(0x09, 0x00) 0 0xf2200000 0x800>,
+ <MBUS_ID(0x01, 0x0f) 0 0xf4000000 0x800000>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&pmx_reset_button>;
+ pinctrl-names = "default";
+
+ reset {
+ label = "Reset Button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&pmx_power_led &pmx_power_led_blink &pmx_wan_led>;
+ pinctrl-names = "default";
+
+ led at 0 {
+ label = "wnr854t:green:power";
+ gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
+ };
+
+ led at 1 {
+ label = "wnr854t:blink:power";
+ gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+ };
+
+ led at 2 {
+ label = "wnr854t:green:wan";
+ gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&devbus_bootcs {
+ status = "okay";
+
+ devbus,keep-config;
+
+ flash at 0 {
+ compatible = "cfi-flash";
+ reg = <0 0x800000>;
+ bank-width = <2>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "kernel";
+ reg = <0x0 0x100000>;
+ };
+
+ partition at 100000 {
+ label = "rootfs";
+ reg = <0x100000 0x660000>;
+ };
+
+ partition at 760000 {
+ label = "uboot_env";
+ reg = <0x760000 0x20000>;
+ };
+
+ partition at 780000 {
+ label = "uboot";
+ reg = <0x780000 0x80000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ switch: switch at 0 {
+ compatible = "marvell,mv88e6085";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ dsa,member = <0 0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ label = "lan3";
+ };
+
+ port at 1 {
+ reg = <1>;
+ label = "lan4";
+ };
+
+ port at 2 {
+ reg = <2>;
+ label = "wan";
+ };
+
+ port at 3 {
+ reg = <3>;
+ label = "cpu";
+ };
+
+ port at 5 {
+ reg = <5>;
+ label = "lan1";
+ };
+
+ port at 7 {
+ reg = <7>;
+ label = "lan2";
+ };
+ };
+ };
+};
+
+ð {
+ status = "okay";
+
+ ethernet-port at 0 {
+ /* Hardwired to DSA switch */
+ speed = <1000>;
+ duplex = <1>;
+ };
+};
+
+&pinctrl {
+ pinctrl-0 = <&pmx_pci_gpios>;
+ pinctrl-names = "default";
+
+ pmx_power_led: pmx-power-led {
+ marvell,pins = "mpp0";
+ marvell,function = "gpio";
+ };
+
+ pmx_reset_button: pmx-reset-button {
+ marvell,pins = "mpp1";
+ marvell,function = "gpio";
+ };
+
+ pmx_power_led_blink: pmx-power-led-blink {
+ marvell,pins = "mpp2";
+ marvell,function = "gpio";
+ };
+
+ pmx_wan_led: pmx-wan-led {
+ marvell,pins = "mpp3";
+ marvell,function = "gpio";
+ };
+
+ pmx_pci_gpios: pmx-pci-gpios {
+ marvell,pins = "mpp4";
+ marvell,function = "gpio";
+ };
+};
+
+&uart0 {
+ /* Pin 1: Tx, Pin 7: Rx, Pin 8: Gnd */
+ status = "okay";
+};
diff --git a/arch/arm/mach-orion5x/Kconfig b/arch/arm/mach-orion5x/Kconfig
index 89bb0fc..9acb37b 100644
--- a/arch/arm/mach-orion5x/Kconfig
+++ b/arch/arm/mach-orion5x/Kconfig
@@ -151,6 +151,12 @@ config MACH_MSS2_DT
Say 'Y' here if you want your kernel to support the
Maxtor Shared Storage II platform.
+config MACH_WNR854T_DT
+ bool "Netgear WNR854T (Flattened Device Tree)"
+ help
+ Say 'Y' here if you want your kernel to support the
+ Netgear WNR854T platform.
+
config MACH_WNR854T
bool "Netgear WNR854T"
help
diff --git a/arch/arm/mach-orion5x/Makefile b/arch/arm/mach-orion5x/Makefile
index 4b2502b..9dff2d3 100644
--- a/arch/arm/mach-orion5x/Makefile
+++ b/arch/arm/mach-orion5x/Makefile
@@ -24,3 +24,4 @@ obj-$(CONFIG_ARCH_ORION5X_DT) += board-dt.o
obj-$(CONFIG_MACH_D2NET_DT) += board-d2net.o
obj-$(CONFIG_MACH_MSS2_DT) += board-mss2.o
obj-$(CONFIG_MACH_RD88F5182_DT) += board-rd88f5182.o
+obj-$(CONFIG_MACH_WNR854T_DT) += board-wnr854t.o
diff --git a/arch/arm/mach-orion5x/board-wnr854t.c b/arch/arm/mach-orion5x/board-wnr854t.c
new file mode 100644
index 0000000..c506e33
--- /dev/null
+++ b/arch/arm/mach-orion5x/board-wnr854t.c
@@ -0,0 +1,78 @@
+/*
+ * Netgear WNR854T PCI setup
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+#include <linux/pci.h>
+#include <asm/mach/pci.h>
+#include "common.h"
+#include "orion5x.h"
+
+#define WNR854T_PCI_SLOT0_OFFS 7
+#define WNR854T_PCI_SLOT0_IRQ_PIN 4
+
+static void __init wnr854t_pci_preinit(void)
+{
+ int pin;
+
+ /*
+ * Configure PCI GPIO IRQ pins
+ */
+ pin = WNR854T_PCI_SLOT0_IRQ_PIN;
+ if (gpio_request(pin, "PCI Int") == 0) {
+ if (gpio_direction_input(pin) == 0) {
+ irq_set_irq_type(gpio_to_irq(pin), IRQ_TYPE_LEVEL_LOW);
+ } else {
+ pr_err("wnr854t_pci_preinit failed to set_irq_type pin %d\n",
+ pin);
+ gpio_free(pin);
+ }
+ } else {
+ pr_err("wnr854t_pci_preinit failed to request gpio %d\n", pin);
+ }
+}
+
+static int __init wnr854t_pci_map_irq(const struct pci_dev *dev, u8 slot,
+ u8 pin)
+{
+ int irq;
+
+ /*
+ * Check for devices with hard-wired IRQs.
+ */
+ irq = orion5x_pci_map_irq(dev, slot, pin);
+ if (irq != -1)
+ return irq;
+
+ /*
+ * PCI IRQs are connected via GPIOs
+ */
+ switch (slot - WNR854T_PCI_SLOT0_OFFS) {
+ case 0:
+ return gpio_to_irq(WNR854T_PCI_SLOT0_IRQ_PIN);
+ default:
+ return -1;
+ }
+}
+
+static struct hw_pci wnr854t_pci __initdata = {
+ .nr_controllers = 2,
+ .preinit = wnr854t_pci_preinit,
+ .setup = orion5x_pci_sys_setup,
+ .scan = orion5x_pci_sys_scan_bus,
+ .map_irq = wnr854t_pci_map_irq,
+};
+
+static int __init wnr854t_pci_init(void)
+{
+ if (of_machine_is_compatible("netgear,wnr854t"))
+ pci_common_init(&wnr854t_pci);
+
+ return 0;
+}
+/* NB: Use late_initcall so we can gpio_request() without being deferred */
+late_initcall(wnr854t_pci_init);
--
2.8.1
More information about the linux-arm-kernel
mailing list