[PATCH 1/3] ARM64: dts: amlogic: Add Meson GX dtsi from GXBB
Neil Armstrong
narmstrong at baylibre.com
Sat Sep 3 01:22:24 PDT 2016
Move all non-gxbb specific nodes to a common GX dtsi.
Signed-off-by: Neil Armstrong <narmstrong at baylibre.com>
---
arch/arm64/boot/dts/amlogic/meson-gx.dtsi | 181 ++++++++++++++++
arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi | 320 +++++++++-------------------
2 files changed, 280 insertions(+), 221 deletions(-)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-gx.dtsi
diff --git a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
new file mode 100644
index 0000000..fb393e9
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
@@ -0,0 +1,181 @@
+/*
+ * Copyright (c) 2016 BayLibre, SAS.
+ * Author: Neil Armstrong <narmstrong at baylibre.com>
+ *
+ * Copyright (c) 2016 Endless Computers, Inc.
+ * Author: Carlo Caione <carlo at endlessm.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <0x2>;
+ #size-cells = <0x0>;
+
+ cpu0: cpu at 0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x0>;
+ enable-method = "psci";
+ };
+
+ cpu1: cpu at 1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x1>;
+ enable-method = "psci";
+ };
+
+ cpu2: cpu at 2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x2>;
+ enable-method = "psci";
+ };
+
+ cpu3: cpu at 3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x3>;
+ enable-method = "psci";
+ };
+ };
+
+ arm-pmu {
+ compatible = "arm,cortex-a53-pmu";
+ interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>;
+ };
+
+ xtal: xtal-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "xtal";
+ #clock-cells = <0>;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ cbus: cbus at c1100000 {
+ compatible = "simple-bus";
+ reg = <0x0 0xc1100000 0x0 0x100000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xc1100000 0x0 0x100000>;
+
+ uart_A: serial at 84c0 {
+ compatible = "amlogic,meson-uart";
+ reg = <0x0 0x084c0 0x0 0x14>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>;
+ status = "disabled";
+ };
+ };
+
+ gic: interrupt-controller at c4301000 {
+ compatible = "arm,gic-400";
+ reg = <0x0 0xc4301000 0 0x1000>,
+ <0x0 0xc4302000 0 0x2000>,
+ <0x0 0xc4304000 0 0x2000>,
+ <0x0 0xc4306000 0 0x2000>;
+ interrupt-controller;
+ interrupts = <GIC_PPI 9
+ (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ };
+
+ aobus: aobus at c8100000 {
+ compatible = "simple-bus";
+ reg = <0x0 0xc8100000 0x0 0x100000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xc8100000 0x0 0x100000>;
+
+ uart_AO: serial at 4c0 {
+ compatible = "amlogic,meson-uart";
+ reg = <0x0 0x004c0 0x0 0x14>;
+ interrupts = <GIC_SPI 193 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>;
+ status = "disabled";
+ };
+ };
+
+ apb: apb at d0000000 {
+ compatible = "simple-bus";
+ reg = <0x0 0xd0000000 0x0 0x200000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xd0000000 0x0 0x200000>;
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
index 2ea7bbd..ff20932 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
@@ -40,9 +40,7 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "meson-gx.dtsi"
#include <dt-bindings/gpio/meson-gxbb-gpio.h>
#include <dt-bindings/reset/amlogic,meson-gxbb-reset.h>
#include <dt-bindings/clock/gxbb-clkc.h>
@@ -51,185 +49,8 @@
/ {
compatible = "amlogic,meson-gxbb";
- interrupt-parent = <&gic>;
- #address-cells = <2>;
- #size-cells = <2>;
-
- cpus {
- #address-cells = <0x2>;
- #size-cells = <0x0>;
-
- cpu0: cpu at 0 {
- device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
- reg = <0x0 0x0>;
- enable-method = "psci";
- };
-
- cpu1: cpu at 1 {
- device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
- reg = <0x0 0x1>;
- enable-method = "psci";
- };
-
- cpu2: cpu at 2 {
- device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
- reg = <0x0 0x2>;
- enable-method = "psci";
- };
-
- cpu3: cpu at 3 {
- device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
- reg = <0x0 0x3>;
- enable-method = "psci";
- };
- };
-
- arm-pmu {
- compatible = "arm,cortex-a53-pmu";
- interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
- };
-
- psci {
- compatible = "arm,psci-0.2";
- method = "smc";
- };
-
- timer {
- compatible = "arm,armv8-timer";
- interrupts = <GIC_PPI 13
- (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>,
- <GIC_PPI 14
- (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>,
- <GIC_PPI 11
- (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>,
- <GIC_PPI 10
- (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>;
- };
-
- xtal: xtal-clk {
- compatible = "fixed-clock";
- clock-frequency = <24000000>;
- clock-output-names = "xtal";
- #clock-cells = <0>;
- };
soc {
- compatible = "simple-bus";
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- cbus: cbus at c1100000 {
- compatible = "simple-bus";
- reg = <0x0 0xc1100000 0x0 0x100000>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges = <0x0 0x0 0x0 0xc1100000 0x0 0x100000>;
-
- reset: reset-controller at 4404 {
- compatible = "amlogic,meson-gxbb-reset";
- reg = <0x0 0x04404 0x0 0x20>;
- #reset-cells = <1>;
- };
-
- uart_A: serial at 84c0 {
- compatible = "amlogic,meson-uart";
- reg = <0x0 0x84c0 0x0 0x14>;
- interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>;
- status = "disabled";
- };
-
- uart_B: serial at 84dc {
- compatible = "amlogic,meson-uart";
- reg = <0x0 0x84dc 0x0 0x14>;
- interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>;
- status = "disabled";
- };
-
- uart_C: serial at 8700 {
- compatible = "amlogic,meson-uart";
- reg = <0x0 0x8700 0x0 0x14>;
- interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>;
- status = "disabled";
- };
-
- watchdog at 98d0 {
- compatible = "amlogic,meson-gxbb-wdt";
- reg = <0x0 0x098d0 0x0 0x10>;
- clocks = <&xtal>;
- };
- };
-
- gic: interrupt-controller at c4301000 {
- compatible = "arm,gic-400";
- reg = <0x0 0xc4301000 0 0x1000>,
- <0x0 0xc4302000 0 0x2000>,
- <0x0 0xc4304000 0 0x2000>,
- <0x0 0xc4306000 0 0x2000>;
- interrupt-controller;
- interrupts = <GIC_PPI 9
- (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
- #interrupt-cells = <3>;
- #address-cells = <0>;
- };
-
- aobus: aobus at c8100000 {
- compatible = "simple-bus";
- reg = <0x0 0xc8100000 0x0 0x100000>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges = <0x0 0x0 0x0 0xc8100000 0x0 0x100000>;
-
- pinctrl_aobus: pinctrl at 14 {
- compatible = "amlogic,meson-gxbb-aobus-pinctrl";
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- gpio_ao: bank at 14 {
- reg = <0x0 0x00014 0x0 0x8>,
- <0x0 0x0002c 0x0 0x4>,
- <0x0 0x00024 0x0 0x8>;
- reg-names = "mux", "pull", "gpio";
- gpio-controller;
- #gpio-cells = <2>;
- };
-
- uart_ao_a_pins: uart_ao_a {
- mux {
- groups = "uart_tx_ao_a", "uart_rx_ao_a";
- function = "uart_ao";
- };
- };
- };
-
- clkc_AO: clock-controller at 040 {
- compatible = "amlogic,gxbb-aoclkc";
- reg = <0x0 0x00040 0x0 0x4>;
- #clock-cells = <1>;
- #reset-cells = <1>;
- };
-
- uart_AO: serial at 4c0 {
- compatible = "amlogic,meson-uart";
- reg = <0x0 0x004c0 0x0 0x14>;
- interrupts = <GIC_SPI 193 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>;
- status = "disabled";
- };
- };
-
periphs: periphs at c8834000 {
compatible = "simple-bus";
reg = <0x0 0xc8834000 0x0 0x2000>;
@@ -340,47 +161,6 @@
};
};
- apb: apb at d0000000 {
- compatible = "simple-bus";
- reg = <0x0 0xd0000000 0x0 0x200000>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges = <0x0 0x0 0x0 0xd0000000 0x0 0x200000>;
-
- sd_emmc_a: mmc at 70000 {
- compatible = "amlogic,meson-gxbb-mmc";
- reg = <0x0 0x70000 0x0 0x2000>;
- interrupts = <GIC_SPI 216 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc CLKID_SD_EMMC_A>,
- <&xtal>,
- <&clkc CLKID_FCLK_DIV2>;
- clock-names = "core", "clkin0", "clkin1";
- status = "disabled";
- };
-
- sd_emmc_b: mmc at 72000 {
- compatible = "amlogic,meson-gxbb-mmc";
- reg = <0x0 0x72000 0x0 0x2000>;
- interrupts = <GIC_SPI 217 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc CLKID_SD_EMMC_B>,
- <&xtal>,
- <&clkc CLKID_FCLK_DIV2>;
- clock-names = "core", "clkin0", "clkin1";
- status = "disabled";
- };
-
- sd_emmc_c: mmc at 74000 {
- compatible = "amlogic,meson-gxbb-mmc";
- reg = <0x0 0x74000 0x0 0x2000>;
- interrupts = <GIC_SPI 218 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc CLKID_SD_EMMC_C>,
- <&xtal>,
- <&clkc CLKID_FCLK_DIV2>;
- clock-names = "core", "clkin0", "clkin1";
- status = "disabled";
- };
- };
-
ethmac: ethernet at c9410000 {
compatible = "amlogic,meson6-dwmac", "snps,dwmac";
reg = <0x0 0xc9410000 0x0 0x10000
@@ -394,3 +174,101 @@
};
};
};
+
+&cbus {
+ reset: reset-controller at 4404 {
+ compatible = "amlogic,meson-gxbb-reset";
+ reg = <0x0 0x04404 0x0 0x20>;
+ #reset-cells = <1>;
+ };
+
+ uart_B: serial at 84dc {
+ compatible = "amlogic,meson-uart";
+ reg = <0x0 0x84dc 0x0 0x14>;
+ interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>;
+ status = "disabled";
+ };
+
+ uart_C: serial at 8700 {
+ compatible = "amlogic,meson-uart";
+ reg = <0x0 0x8700 0x0 0x14>;
+ interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>;
+ status = "disabled";
+ };
+
+ watchdog at 98d0 {
+ compatible = "amlogic,meson-gxbb-wdt";
+ reg = <0x0 0x098d0 0x0 0x10>;
+ clocks = <&xtal>;
+ };
+};
+
+&aobus {
+ pinctrl_aobus: pinctrl at 14 {
+ compatible = "amlogic,meson-gxbb-aobus-pinctrl";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ gpio_ao: bank at 14 {
+ reg = <0x0 0x00014 0x0 0x8>,
+ <0x0 0x0002c 0x0 0x4>,
+ <0x0 0x00024 0x0 0x8>;
+ reg-names = "mux", "pull", "gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ uart_ao_a_pins: uart_ao_a {
+ mux {
+ groups = "uart_tx_ao_a", "uart_rx_ao_a";
+ function = "uart_ao";
+ };
+ };
+ };
+
+ clkc_AO: clock-controller at 040 {
+ compatible = "amlogic,gxbb-aoclkc";
+ reg = <0x0 0x00040 0x0 0x4>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+};
+
+&apb {
+ sd_emmc_a: mmc at 70000 {
+ compatible = "amlogic,meson-gxbb-mmc";
+ reg = <0x0 0x70000 0x0 0x2000>;
+ interrupts = <GIC_SPI 216 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc CLKID_SD_EMMC_A>,
+ <&xtal>,
+ <&clkc CLKID_FCLK_DIV2>;
+ clock-names = "core", "clkin0", "clkin1";
+ status = "disabled";
+ };
+
+ sd_emmc_b: mmc at 72000 {
+ compatible = "amlogic,meson-gxbb-mmc";
+ reg = <0x0 0x72000 0x0 0x2000>;
+ interrupts = <GIC_SPI 217 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc CLKID_SD_EMMC_B>,
+ <&xtal>,
+ <&clkc CLKID_FCLK_DIV2>;
+ clock-names = "core", "clkin0", "clkin1";
+ status = "disabled";
+ };
+
+ sd_emmc_c: mmc at 74000 {
+ compatible = "amlogic,meson-gxbb-mmc";
+ reg = <0x0 0x74000 0x0 0x2000>;
+ interrupts = <GIC_SPI 218 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc CLKID_SD_EMMC_C>,
+ <&xtal>,
+ <&clkc CLKID_FCLK_DIV2>;
+ clock-names = "core", "clkin0", "clkin1";
+ status = "disabled";
+ };
+};
+
--
2.7.0
More information about the linux-arm-kernel
mailing list