[PATCH 5/7] ARM: sun8i: a33: Add display pipeline
Chen-Yu Tsai
wens at csie.org
Thu Sep 1 23:28:54 PDT 2016
Hi,
On Thu, Sep 1, 2016 at 11:32 PM, Maxime Ripard
<maxime.ripard at free-electrons.com> wrote:
> Add all the needed blocks to the A33 DTSI.
>
> Signed-off-by: Maxime Ripard <maxime.ripard at free-electrons.com>
> ---
> arch/arm/boot/dts/sun8i-a33.dtsi | 184 +++++++++++++++++++++++++++++++++++++++
> 1 file changed, 184 insertions(+)
>
> diff --git a/arch/arm/boot/dts/sun8i-a33.dtsi b/arch/arm/boot/dts/sun8i-a33.dtsi
> index deb0cd613e97..5f9dbd17eb50 100644
> --- a/arch/arm/boot/dts/sun8i-a33.dtsi
> +++ b/arch/arm/boot/dts/sun8i-a33.dtsi
> @@ -64,6 +64,42 @@
> };
>
> soc at 01c00000 {
> + tcon0: lcd-controller at 01c0c000 {
> + compatible = "allwinner,sun8i-a23-tcon";
> + reg = <0x01c0c000 0x1000>;
> + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_LCD>,
> + <&ccu CLK_LCD_CH0>;
> + clock-names = "ahb",
> + "tcon-ch0";
> + clock-output-names = "tcon-pixel-clock";
> + resets = <&ccu RST_BUS_LCD>;
> + reset-names = "lcd";
> + status = "disabled";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + tcon0_in: port at 0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + tcon0_in_drc0: endpoint at 0 {
> + reg = <0>;
> + remote-endpoint = <&drc0_out_tcon0>;
> + };
> + };
> +
> + tcon0_out: port at 1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> + };
> + };
> + };
> +
> crypto: crypto-engine at 01c15000 {
> compatible = "allwinner,sun4i-a10-crypto";
> reg = <0x01c15000 0x1000>;
> @@ -104,6 +140,154 @@
> status = "disabled";
> #phy-cells = <1>;
> };
> +
> + fe0: display-frontend at 01e00000 {
> + compatible = "allwinner,sun8i-a33-display-frontend";
> + reg = <0x01e00000 0x20000>;
> + interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_DE_FE>, <&ccu CLK_DE_FE>,
> + <&ccu CLK_DRAM_DE_FE>;
> + clock-names = "ahb", "mod",
> + "ram";
> + resets = <&ccu RST_BUS_DE_FE>;
> + status = "disabled";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + fe0_out: port at 1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> +
> + fe0_out_sat0: endpoint at 0 {
> + reg = <0>;
> + remote-endpoint = <&sat0_in_fe0>;
> + };
> + };
> + };
> + };
> +
> + be0: display-backend at 01e60000 {
> + compatible = "allwinner,sun8i-a33-display-backend";
> + reg = <0x01e60000 0x10000>;
Please also list the interrupt, even though we don't use it yet.
The manual says it's 127 - 32 = 95.
> + clocks = <&ccu CLK_BUS_DE_BE>, <&ccu CLK_DE_BE>,
> + <&ccu CLK_DRAM_DE_BE>;
> + clock-names = "ahb", "mod",
> + "ram";
> + resets = <&ccu RST_BUS_DE_BE>;
> +
> + assigned-clocks = <&ccu CLK_DE_BE>;
> + assigned-clock-rates = <300000000>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + be0_in: port at 0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + be0_in_sat0: endpoint at 0 {
> + reg = <0>;
> + remote-endpoint = <&sat0_out_be0>;
> + };
> + };
> +
> + be0_out: port at 1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> +
> + be0_out_drc0: endpoint at 0 {
> + reg = <0>;
> + remote-endpoint = <&drc0_in_be0>;
> + };
> + };
> + };
> + };
> +
> + drc0: drc at 01e70000 {
> + compatible = "allwinner,sun8i-a33-drc";
> + reg = <0x01e70000 0x10000>;
> + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_DRC>, <&ccu CLK_DRC>,
> + <&ccu CLK_DRAM_DRC>;
> + clock-names = "ahb", "mod", "ram";
> + resets = <&ccu RST_BUS_DRC>;
> +
> + assigned-clocks = <&ccu CLK_DRC>;
> + assigned-clock-rates = <300000000>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + drc0_in: port at 0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + drc0_in_be0: endpoint at 0 {
> + reg = <0>;
> + remote-endpoint = <&be0_out_drc0>;
> + };
> + };
> +
> + drc0_out: port at 1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> +
> + drc0_out_tcon0: endpoint at 0 {
> + reg = <0>;
> + remote-endpoint = <&tcon0_in_drc0>;
> + };
> + };
> + };
> + };
> +
> + sat0: sat at 01e80000 {
> + compatible = "allwinner,sun8i-a33-sat";
> + reg = <0x01e80000 0x1000>;
> + clocks = <&ccu CLK_BUS_SAT>;
> + resets = <&ccu RST_BUS_SAT>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + sat0_in: port at 0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + sat0_in_fe0: endpoint at 0 {
> + reg = <0>;
> + remote-endpoint = <&fe0_out_sat0>;
> + };
> + };
> +
> + sat0_out: port at 1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> +
> + sat0_out_be0: endpoint at 0 {
> + reg = <0>;
> + remote-endpoint = <&be0_in_sat0>;
> + };
> + };
I'm worried about the representation here.
In the user manuals, the SAT is shown as part of the BE.
Look at it this way: if it did come before the BE and is
independent, we shouldn't have to bring the SAT out of
reset for simplefb to work.
For comparison, a similar function unit called "CMU" found on
the other post-sun6i SoCs has the same function description as
SAT on the A33. It uses the reserved registers at the beginning
of the BE address space.
> + };
> + };
> + };
> +
> + de: display-engine {
> + compatible = "allwinner,sun8i-a33-display-engine";
> + allwinner,pipelines = <&fe0>;
> + status = "disabled";
> };
Put this node above soc@? Properly sorted that is.
Everything else looks good.
Regards
ChenYu
> };
>
> --
> 2.9.2
>
More information about the linux-arm-kernel
mailing list