[PATCH v5] Axi-usb: Add support for 64-bit addressing.

[Nava kishore Manne]

This patch updates the driver to support 64-bit DMA addressing.

Signed-off-by: Nava kishore Manne <navam at xilinx.com>
Acked-by: Rob Herring <robh at kernel.org>
---
Changes for v5:
                -None.

Changes for v4:
                -Used boolen property insted of addrwith property in the DT
                 as suggested by Arnd Bergmann.
                -Adopt the DT relevant changes into the driver.

Changes for v3:
                -Added new compatable string for 5.00 IP version as suggested by
                 Arnd Bergmann.
                -Used write_fn() insted of lo_hi_writeq() as suggested by
                 Arnd Bergmann.
Changes for v2:
                -Added dma-ranges property in device tree as suggested by
                 Arnd Bergmann.
                -Modified the driver code based on the xlnx,addrwidth.

 .../devicetree/bindings/usb/udc-xilinx.txt         |  5 ++-
 drivers/usb/gadget/udc/udc-xilinx.c                | 52 +++++++++++++++++++++-
 2 files changed, 54 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/usb/udc-xilinx.txt b/Documentation/devicetree/bindings/usb/udc-xilinx.txt
index 47b4e39..d08d972 100644
--- a/Documentation/devicetree/bindings/usb/udc-xilinx.txt
+++ b/Documentation/devicetree/bindings/usb/udc-xilinx.txt
@@ -1,12 +1,14 @@
 Xilinx USB2 device controller
 
 Required properties:
-- compatible		: Should be "xlnx,usb2-device-4.00.a"
+- compatible		: Should be "xlnx,usb2-device-4.00.a" or
+			  "xlnx,usb2-device-5.00"
 - reg			: Physical base address and size of the USB2
 			  device registers map.
 - interrupts		: Should contain single irq line of USB2 device
 			  controller
 - xlnx,has-builtin-dma	: if DMA is included
+- xlnx,has-64bit-dma	: if DMA is included 64-bit addressing support.
 
 Example:
  		axi-usb2-device at 42e00000 {
@@ -14,5 +16,6 @@ Example:
                         interrupts = <0x0 0x39 0x1>;
                         reg = <0x42e00000 0x10000>;
                         xlnx,has-builtin-dma;
+			xlnx,has-64bit-dma;
                 };
 
diff --git a/drivers/usb/gadget/udc/udc-xilinx.c b/drivers/usb/gadget/udc/udc-xilinx.c
index 1cbb0ac..6fb80c6 100644
--- a/drivers/usb/gadget/udc/udc-xilinx.c
+++ b/drivers/usb/gadget/udc/udc-xilinx.c
@@ -47,6 +47,15 @@
 #define XUSB_DMA_LENGTH_OFFSET		0x0210	/* DMA Length Register */
 #define XUSB_DMA_STATUS_OFFSET		0x0214	/* DMA Status Register */
 
+/* DMA source Address Reg for LSB */
+#define XUSB_DMA_DSAR_ADDR_OFFSET_LSB   0x0308
+/* DMA source Address Reg for MSB */
+#define XUSB_DMA_DSAR_ADDR_OFFSET_MSB   0x030C
+/* DMA destination Addr Reg LSB */
+#define XUSB_DMA_DDAR_ADDR_OFFSET_LSB   0x0310
+/* DMA destination Addr Reg MSB */
+#define XUSB_DMA_DDAR_ADDR_OFFSET_MSB   0x0314
+
 /* Endpoint Configuration Space offsets */
 #define XUSB_EP_CFGSTATUS_OFFSET	0x00	/* Endpoint Config Status  */
 #define XUSB_EP_BUF0COUNT_OFFSET	0x08	/* Buffer 0 Count */
@@ -169,6 +178,7 @@ struct xusb_ep {
  * @setup: usb_ctrlrequest structure for control requests
  * @req: pointer to dummy request for get status command
  * @dev: pointer to device structure in gadget
+ * @is_extend_dma: flag indiacting whether the dma is 64-bit support or not.
  * @usb_state: device in suspended state or not
  * @remote_wkp: remote wakeup enabled by host
  * @setupseqtx: tx status
@@ -186,6 +196,7 @@ struct xusb_udc {
 	struct usb_ctrlrequest setup;
 	struct xusb_req *req;
 	struct device *dev;
+	bool is_extend_dma;
 	u32 usb_state;
 	u32 remote_wkp;
 	u32 setupseqtx;
@@ -215,6 +226,20 @@ static const struct usb_endpoint_descriptor config_bulk_out_desc = {
 };
 
 /**
+ * xudc_write64 - write 64bit value to device registers
+ * @ep: pointer to the usb device endpoint structure.
+ * @offset: register offset
+ * @val: data to be written
+ **/
+static void xudc_write64(struct xusb_ep *ep, u32 offset, u64 val)
+{
+	struct xusb_udc *udc = ep->udc;
+
+	udc->write_fn(udc->addr, offset, lower_32_bits(val));
+	udc->write_fn(udc->addr, offset+0x04, upper_32_bits(val));
+}
+
+/**
  * xudc_write32 - little endian write to device registers
  * @addr: base addr of device registers
  * @offset: register offset
@@ -330,8 +355,13 @@ static int xudc_start_dma(struct xusb_ep *ep, dma_addr_t src,
 	 * destination registers and then set the length
 	 * into the DMA length register.
 	 */
-	udc->write_fn(udc->addr, XUSB_DMA_DSAR_ADDR_OFFSET, src);
-	udc->write_fn(udc->addr, XUSB_DMA_DDAR_ADDR_OFFSET, dst);
+	if (udc->is_extend_dma) {
+		xudc_write64(ep, XUSB_DMA_DSAR_ADDR_OFFSET_LSB, src);
+		xudc_write64(ep, XUSB_DMA_DDAR_ADDR_OFFSET_LSB, dst);
+	} else {
+		udc->write_fn(udc->addr, XUSB_DMA_DSAR_ADDR_OFFSET, src);
+		udc->write_fn(udc->addr, XUSB_DMA_DDAR_ADDR_OFFSET, dst);
+	}
 	udc->write_fn(udc->addr, XUSB_DMA_LENGTH_OFFSET, length);
 
 	/*
@@ -2097,6 +2127,23 @@ static int xudc_probe(struct platform_device *pdev)
 
 	udc->dma_enabled = of_property_read_bool(np, "xlnx,has-builtin-dma");
 
+	udc->is_extend_dma = false;
+
+	if (of_device_is_compatible(np, "xlnx,usb2-device-5.00"))
+		udc->is_extend_dma = of_property_read_bool(np,
+						"xlnx,has-64bit-dma");
+
+	/* Set the dma mask bits */
+	if (udc->is_extend_dma)
+		ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64));
+	else
+		ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
+
+	if (ret < 0) {
+		dev_dbg(&pdev->dev, "no usable DMA configuration");
+		goto fail;
+	}
+
 	/* Setup gadget structure */
 	udc->gadget.ops = &xusb_udc_ops;
 	udc->gadget.max_speed = USB_SPEED_HIGH;
@@ -2168,6 +2215,7 @@ static int xudc_remove(struct platform_device *pdev)
 /* Match table for of_platform binding */
 static const struct of_device_id usb_of_match[] = {
 	{ .compatible = "xlnx,usb2-device-4.00.a", },
+	{ .compatible = "xlnx,usb2-device-5.00", },
 	{ /* end of list */ },
 };
 MODULE_DEVICE_TABLE(of, usb_of_match);
-- 
2.1.2