[PATCH] ARM: DT: stm32: move dma translation to board files
Bruno Herrera
bruherrera at gmail.com
Mon Oct 31 03:27:48 PDT 2016
On Fri, Oct 28, 2016 at 5:09 AM, Radosław Pietrzyk
<radoslaw.pietrzyk at gmail.com> wrote:
> Have you defined your sdio node within soc node ?
It is in the SOC node of the DSTI file.
>
> 2016-10-27 14:57 GMT+02:00 Bruno Herrera <bruherrera at gmail.com>:
>>
>> Hi Alex,
>>
>> On Thu, Oct 27, 2016 at 10:21 AM, Alexandre Torgue
>> <alexandre.torgue at st.com> wrote:
>> > Hi Bruno,
>> >
>> >
>> > On 10/27/2016 12:43 PM, Bruno Herrera wrote:
>> >>
>> >> Hi Alex,
>> >>
>> >> On Wed, Oct 26, 2016 at 7:09 AM, Alexandre Torgue
>> >> <alexandre.torgue at st.com> wrote:
>> >>>
>> >>> Hi Bruno,
>> >>>
>> >>> On 10/25/2016 11:06 PM, Bruno Herrera wrote:
>> >>>>
>> >>>>
>> >>>> Hi Alexandre,
>> >>>>
>> >>>>>
>> >>>>> stm32f469-disco and stm32f429-eval boards use SDRAM start address
>> >>>>> remapping
>> >>>>> (to @0) to boost performances. A DMA translation through
>> >>>>> "dma-ranges"
>> >>>>> property was needed for other masters than the M4 CPU.
>> >>>>> stm32f429-disco doesn't use remapping so doesn't need this DMA
>> >>>>> translation.
>> >>>>> This patches moves this DMA translation definition from stm32f429
>> >>>>> soc
>> >>>>> file
>> >>>>> to board files.
>> >>>>>
>> >>>>> Signed-off-by: Alexandre TORGUE <alexandre.torgue at st.com>
>> >>>>>
>> >>>>> diff --git a/arch/arm/boot/dts/stm32429i-eval.dts
>> >>>>> b/arch/arm/boot/dts/stm32429i-eval.dts
>> >>>>> index 13c7cd2..a763c15 100644
>> >>>>> --- a/arch/arm/boot/dts/stm32429i-eval.dts
>> >>>>> +++ b/arch/arm/boot/dts/stm32429i-eval.dts
>> >>>>> @@ -82,6 +82,10 @@
>> >>>>> };
>> >>>>> };
>> >>>>>
>> >>>>> + soc {
>> >>>>> + dma-ranges = <0xc0000000 0x0 0x10000000>;
>> >>>>> + };
>> >>>>> +
>> >>>>> usbotg_hs_phy: usbphy {
>> >>>>> #phy-cells = <0>;
>> >>>>> compatible = "usb-nop-xceiv";
>> >>>>
>> >>>>
>> >>>>
>> >>>> Shouldn't also the peripheral dma-ranges property move to board
>> >>>> specific
>> >>>> too?
>> >>>> I had this patch for while but I didn't had the time to submit:
>> >>>
>> >>>
>> >>>
>> >>> Well spot I forgot it. Actually, discussing with Arnd ysterday on
>> >>> IIRC,
>> >>> empty dma-ranges is not needed. Can you test on your side by removing
>> >>> dma-ranges in usb node please ?
>> >>
>> >> Unfortunately will take a time for me to set up this environment on
>> >> the STM32F4-EVAL board.
>> >> And on the discovery boards we dont have this scenario. That was the
>> >> main reason I did not submit the patch right away.
>> >> My conclusion and I might be wrong but is based on the my tests with
>> >> SDIO device at STM32F469I-DISCO board.
>> >>
>> >> I started this issue as discussion at ST Forum but Maxime gave me the
>> >> hint.
>> >>
>> >>
>> >>
>> >> https://my.st.com/public/STe2ecommunities/mcu/Lists/cortex_mx_stm32/Flat.aspx?RootFolder=https%3a%2f%2fmy%2est%2ecom%2fpublic%2fSTe2ecommunities%2fmcu%2fLists%2fcortex_mx_stm32%2fDMA2%20and%20SYSCFG_MEMRMP%20relationship&FolderCTID=0x01200200770978C69A1141439FE559EB459D7580009C4E14902C3CDE46A77F0FFD06506F5B¤tviews=44
>> >>
>> >>> I will push a v2 by removing empty dma-ranges if tests are ok in your
>> >>> side.
>> >>
>> >>
>> >> From my understating/conclusion is: when empty property(dma-ranges) is
>> >> the device node, the mapping will be taken in consideration when using
>> >> DMA otherwise the mapping is ignored.
>> >> And in the SDIO case it is needed for DEV->MEM(SDRAM) and
>> >> MEM(SDRAM)->DEV. If it is not the case for the devices in question so
>> >> I suppose it can work without the property.
>> >
>> >
>> > For sure translation has to be done but I'm not sure that an empty
>> > "dma-ranges" is needed in device node to activate it. For Ethernet empty
>> > "dma-ranges" is not needed. I will try with usb.
>>
>> In the case of SDIO it is needed. As example this is my working SDIO node:
>>
>> sdio: sdio at 40012c00 {
>> compatible = "arm,pl18x", "arm,primecell";
>> arm,primecell-periphid = <0x00480181>;
>> reg = <0x40012c00 0x400>;
>> dmas = <&dma2 6 4 0x10400 0x3>, /* Logical - DevToMem */
>> <&dma2 3 4 0x10400 0x3>; /* Logical - MemToDev */
>> dma-names = "rx", "tx";
>> clocks = <&rcc 0 171>;
>> clock-names = "apb_pclk";
>> interrupts = <49>;
>> status = "disabled";
>> };
>>
>> &sdio {
>> status = "okay";
>> vmmc-supply = <&wlan_en>;
>> bus-width = <4>;
>> max-frequency = <24000000>;
>> pinctrl-names = "default";
>> pinctrl-0 = <&sdio_pins>;
>> ti,non-removable;
>> ti,needs-special-hs-handling;
>> dma-ranges;
>> cap-power-off-card;
>> keep-power-in-suspend;
>>
>> #address-cells = <1>;
>> #size-cells = <0>;
>> wlcore: wlcore at 0 {
>> compatible = "ti,wl1835";
>> reg = <2>;
>> interrupt-parent = <&gpioa>;
>> interrupts = <8 IRQ_TYPE_EDGE_RISING>;
>> };
>> };
>>
>> >
>> > alex
>> >
>> >
>> >>
>> >>>
>> >>> Thanks in advance
>> >>> Alex
>> >>>
>> >>>
>> >>>>
>> >>>> Author: Bruno Herrera <bruherrera at gmail.com>
>> >>>> Date: Sun Oct 16 14:50:00 2016 -0200
>> >>>>
>> >>>> ARM: DT: STM32: Use dma-ranges property per board not at dtsi
>> >>>> file
>> >>>>
>> >>>> diff --git a/arch/arm/boot/dts/stm32429i-eval.dts
>> >>>> b/arch/arm/boot/dts/stm32429i-eval.dts
>> >>>> index 6bfc595..2a22a82 100644
>> >>>> --- a/arch/arm/boot/dts/stm32429i-eval.dts
>> >>>> +++ b/arch/arm/boot/dts/stm32429i-eval.dts
>> >>>> @@ -52,6 +52,10 @@
>> >>>> model = "STMicroelectronics STM32429i-EVAL board";
>> >>>> compatible = "st,stm32429i-eval", "st,stm32f429";
>> >>>>
>> >>>> + soc {
>> >>>> + dma-ranges = <0xC0000000 0x0 0x10000000>;
>> >>>> + };
>> >>>> +
>> >>>> chosen {
>> >>>> bootargs = "root=/dev/ram rdinit=/linuxrc";
>> >>>> stdout-path = "serial0:115200n8";
>> >>>> @@ -96,6 +100,7 @@
>> >>>>
>> >>>> ðernet0 {
>> >>>> status = "okay";
>> >>>> + dma-ranges;
>> >>>> pinctrl-0 = <ðernet0_mii>;
>> >>>> pinctrl-names = "default";
>> >>>> phy-mode = "mii-id";
>> >>>> @@ -116,6 +121,7 @@
>> >>>> };
>> >>>>
>> >>>> &usbotg_hs {
>> >>>> + dma-ranges;
>> >>>> dr_mode = "host";
>> >>>> phys = <&usbotg_hs_phy>;
>> >>>> phy-names = "usb2-phy";
>> >>>> diff --git a/arch/arm/boot/dts/stm32f429.dtsi
>> >>>> b/arch/arm/boot/dts/stm32f429.dtsi
>> >>>> index 7d624a2..697a133 100644
>> >>>> --- a/arch/arm/boot/dts/stm32f429.dtsi
>> >>>> +++ b/arch/arm/boot/dts/stm32f429.dtsi
>> >>>> @@ -59,7 +59,6 @@
>> >>>> };
>> >>>>
>> >>>> soc {
>> >>>> - dma-ranges = <0xc0000000 0x0 0x10000000>;
>> >>>>
>> >>>> timer2: timer at 40000000 {
>> >>>> compatible = "st,stm32-timer";
>> >>>> @@ -472,13 +471,11 @@
>> >>>> st,syscon = <&syscfg 0x4>;
>> >>>> snps,pbl = <8>;
>> >>>> snps,mixed-burst;
>> >>>> - dma-ranges;
>> >>>> status = "disabled";
>> >>>> };
>> >>>>
>> >>>> usbotg_hs: usb at 40040000 {
>> >>>> compatible = "snps,dwc2";
>> >>>> - dma-ranges;
>> >>>> reg = <0x40040000 0x40000>;
>> >>>> interrupts = <77>;
>> >>>> clocks = <&rcc 0 29>;
>> >>>>
>> >>>>
>> >>>>> diff --git a/arch/arm/boot/dts/stm32f429.dtsi
>> >>>>> b/arch/arm/boot/dts/stm32f429.dtsi
>> >>>>> index 0596d60..3a1cfdd 100644
>> >>>>> --- a/arch/arm/boot/dts/stm32f429.dtsi
>> >>>>> +++ b/arch/arm/boot/dts/stm32f429.dtsi
>> >>>>> @@ -59,8 +59,6 @@
>> >>>>> };
>> >>>>>
>> >>>>> soc {
>> >>>>> - dma-ranges = <0xc0000000 0x0 0x10000000>;
>> >>>>> -
>> >>>>> timer2: timer at 40000000 {
>> >>>>> compatible = "st,stm32-timer";
>> >>>>> reg = <0x40000000 0x400>;
>> >>>>> diff --git a/arch/arm/boot/dts/stm32f469-disco.dts
>> >>>>> b/arch/arm/boot/dts/stm32f469-disco.dts
>> >>>>> index 9e73656..c2213c0 100644
>> >>>>> --- a/arch/arm/boot/dts/stm32f469-disco.dts
>> >>>>> +++ b/arch/arm/boot/dts/stm32f469-disco.dts
>> >>>>> @@ -64,6 +64,10 @@
>> >>>>> aliases {
>> >>>>> serial0 = &usart3;
>> >>>>> };
>> >>>>> +
>> >>>>> + soc {
>> >>>>> + dma-ranges = <0xc0000000 0x0 0x10000000>;
>> >>>>> + };
>> >>>>> };
>> >>>>>
>> >>>>> &clk_hse {
>> >>>>> --
>> >>>>
>> >>>>
>> >>>>
>> >>>>
>> >>>> Br.,
>> >>>> Bruno
>> >>>>
>> >>>
>> >
>>
>> _______________________________________________
>> linux-arm-kernel mailing list
>> linux-arm-kernel at lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>
>
More information about the linux-arm-kernel
mailing list