[PATCH 1/3] ARM: dts: Add support for OX820 and Pogoplug V3
Neil Armstrong
narmstrong at baylibre.com
Fri Oct 21 08:10:35 PDT 2016
Add device tree for the Oxford Seminconductor OX820 SoC and the
Cloud Engines PogoPlug v3 board.
Add the SoC and board compatible strings to oxnas bindings.
Acked-by: Rob Herring <robh at kernel.org>
Signed-off-by: Neil Armstrong <narmstrong at baylibre.com>
---
Documentation/devicetree/bindings/arm/oxnas.txt | 5 +
arch/arm/boot/dts/Makefile | 3 +-
.../boot/dts/cloudengines-pogoplug-series-3.dts | 94 +++++++
arch/arm/boot/dts/ox820.dtsi | 298 +++++++++++++++++++++
4 files changed, 399 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/cloudengines-pogoplug-series-3.dts
create mode 100644 arch/arm/boot/dts/ox820.dtsi
diff --git a/Documentation/devicetree/bindings/arm/oxnas.txt b/Documentation/devicetree/bindings/arm/oxnas.txt
index b9e4971..ac64e60 100644
--- a/Documentation/devicetree/bindings/arm/oxnas.txt
+++ b/Documentation/devicetree/bindings/arm/oxnas.txt
@@ -5,5 +5,10 @@ Boards with the OX810SE SoC shall have the following properties:
Required root node property:
compatible: "oxsemi,ox810se"
+Boards with the OX820 SoC shall have the following properties:
+ Required root node property:
+ compatible: "oxsemi,ox820"
+
Board compatible values:
- "wd,mbwe" (OX810SE)
+ - "cloudengines,pogoplugv3" (OX820)
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index befcd26..3b0c74f 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -604,7 +604,8 @@ dtb-$(CONFIG_ARCH_ORION5X) += \
dtb-$(CONFIG_ARCH_PRIMA2) += \
prima2-evb.dtb
dtb-$(CONFIG_ARCH_OXNAS) += \
- wd-mbwe.dtb
+ wd-mbwe.dtb \
+ cloudengines-pogoplug-series-3.dtb
dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8060-dragonboard.dtb \
qcom-apq8064-arrow-sd-600eval.dtb \
diff --git a/arch/arm/boot/dts/cloudengines-pogoplug-series-3.dts b/arch/arm/boot/dts/cloudengines-pogoplug-series-3.dts
new file mode 100644
index 0000000..bfde32e
--- /dev/null
+++ b/arch/arm/boot/dts/cloudengines-pogoplug-series-3.dts
@@ -0,0 +1,94 @@
+/*
+ * cloudengines-pogoplug-series-3.dtsi - Device tree file for Cloud Engines PogoPlug Series 3
+ *
+ * Copyright (C) 2016 Neil Armstrong <narmstrong at baylibre.com>
+ *
+ * Licensed under GPLv2 or later
+ */
+
+/dts-v1/;
+#include "ox820.dtsi"
+
+/ {
+ model = "Cloud Engines PogoPlug Series 3";
+
+ compatible = "cloudengines,pogoplugv3", "oxsemi,ox820";
+
+ chosen {
+ bootargs = "earlyprintk";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory {
+ /* 128Mbytes DDR */
+ reg = <0x60000000 0x8000000>;
+ };
+
+ aliases {
+ serial0 = &uart0;
+ gpio0 = &gpio0;
+ gpio1 = &gpio1;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ blue {
+ label = "pogoplug:blue";
+ gpios = <&gpio0 2 0>;
+ default-state = "keep";
+ };
+
+ orange {
+ label = "pogoplug:orange";
+ gpios = <&gpio1 16 1>;
+ default-state = "keep";
+ };
+
+ green {
+ label = "pogoplug:green";
+ gpios = <&gpio1 17 1>;
+ default-state = "keep";
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart0>;
+};
+
+&nandc {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_nand>;
+
+ nand at 0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ nand-ecc-mode = "soft";
+ nand-ecc-algo = "hamming";
+
+ partition at 0 {
+ label = "boot";
+ reg = <0x00000000 0x00e00000>;
+ read-only;
+ };
+
+ partition at e00000 {
+ label = "ubi";
+ reg = <0x00e00000 0x07200000>;
+ };
+ };
+};
+
+ða {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_etha_mdio>;
+};
diff --git a/arch/arm/boot/dts/ox820.dtsi b/arch/arm/boot/dts/ox820.dtsi
new file mode 100644
index 0000000..4592075
--- /dev/null
+++ b/arch/arm/boot/dts/ox820.dtsi
@@ -0,0 +1,298 @@
+/*
+ * ox820.dtsi - Device tree file for Oxford Semiconductor OX820 SoC
+ *
+ * Copyright (C) 2016 Neil Armstrong <narmstrong at baylibre.com>
+ *
+ * Licensed under GPLv2 or later
+ */
+
+/include/ "skeleton.dtsi"
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/oxsemi,ox820.h>
+#include <dt-bindings/reset/oxsemi,ox820.h>
+
+/ {
+ compatible = "oxsemi,ox820";
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ enable-method = "oxsemi,ox820-smp";
+
+ cpu at 0 {
+ device_type = "cpu";
+ compatible = "arm,arm11mpcore";
+ clocks = <&armclk>;
+ reg = <0>;
+ };
+
+ cpu at 1 {
+ device_type = "cpu";
+ compatible = "arm,arm11mpcore";
+ clocks = <&armclk>;
+ reg = <1>;
+ };
+ };
+
+ memory {
+ /* Max 512MB @ 0x60000000 */
+ reg = <0x60000000 0x20000000>;
+ };
+
+ clocks {
+ osc: oscillator {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ };
+
+ gmacclk: gmacclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <125000000>;
+ };
+
+ sysclk: sysclk {
+ compatible = "fixed-factor-clock";
+ #clock-cells = <0>;
+ clock-div = <4>;
+ clock-mult = <1>;
+ clocks = <&osc>;
+ };
+
+ plla: plla {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <850000000>;
+ };
+
+ armclk: armclk {
+ compatible = "fixed-factor-clock";
+ #clock-cells = <0>;
+ clock-div = <2>;
+ clock-mult = <1>;
+ clocks = <&plla>;
+ };
+ };
+
+ soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ ranges;
+ interrupt-parent = <&gic>;
+
+ nandc: nand-controller at 41000000 {
+ compatible = "oxsemi,ox820-nand";
+ reg = <0x41000000 0x100000>;
+ clocks = <&stdclk CLK_820_NAND>;
+ resets = <&reset RESET_NAND>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ etha: ethernet at 40400000 {
+ compatible = "oxsemi,ox820-dwmac", "snps,dwmac";
+ reg = <0x40400000 0x2000>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq", "eth_wake_irq";
+ mac-address = [000000000000]; /* Filled in by U-Boot */
+ phy-mode = "rgmii";
+
+ clocks = <&stdclk CLK_820_ETHA>, <&gmacclk>;
+ clock-names = "gmac", "stmmaceth";
+ resets = <&reset RESET_MAC>;
+
+ /* Regmap for sys registers */
+ oxsemi,sys-ctrl = <&sys>;
+
+ status = "disabled";
+ };
+
+ apb-bridge at 44000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ ranges = <0 0x44000000 0x1000000>;
+
+ pinctrl: pinctrl {
+ compatible = "oxsemi,ox820-pinctrl";
+
+ /* Regmap for sys registers */
+ oxsemi,sys-ctrl = <&sys>;
+
+ pinctrl_uart0: uart0 {
+ uart0 {
+ pins = "gpio30", "gpio31";
+ function = "fct5";
+ };
+ };
+
+ pinctrl_uart0_modem: uart0_modem {
+ uart0_modem_a {
+ pins = "gpio24", "gpio24", "gpio26", "gpio27";
+ function = "fct4";
+ };
+ uart0_modem_b {
+ pins = "gpio28", "gpio29";
+ function = "fct5";
+ };
+ };
+
+ pinctrl_uart1: uart1 {
+ uart1 {
+ pins = "gpio7", "gpio8";
+ function = "fct4";
+ };
+ };
+
+ pinctrl_uart1_modem: uart1_modem {
+ uart1_modem {
+ pins = "gpio5", "gpio6", "gpio40", "gpio41", "gpio42", "gpio43";
+ function = "fct4";
+ };
+ };
+
+ pinctrl_etha_mdio: etha_mdio {
+ etha_mdio {
+ pins = "gpio3", "gpio4";
+ function = "fct1";
+ };
+ };
+
+ pinctrl_nand: nand {
+ nand {
+ pins = "gpio12", "gpio13", "gpio14", "gpio15",
+ "gpio16", "gpio17", "gpio18", "gpio19",
+ "gpio20", "gpio21", "gpio22", "gpio23",
+ "gpio24";
+ function = "fct1";
+ };
+ };
+ };
+
+ gpio0: gpio at 000000 {
+ compatible = "oxsemi,ox820-gpio";
+ reg = <0x000000 0x100000>;
+ interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ ngpios = <32>;
+ oxsemi,gpio-bank = <0>;
+ gpio-ranges = <&pinctrl 0 0 32>;
+ };
+
+ gpio1: gpio at 100000 {
+ compatible = "oxsemi,ox820-gpio";
+ reg = <0x100000 0x100000>;
+ interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ ngpios = <18>;
+ oxsemi,gpio-bank = <1>;
+ gpio-ranges = <&pinctrl 0 32 18>;
+ };
+
+ uart0: serial at 200000 {
+ compatible = "ns16550a";
+ reg = <0x200000 0x100000>;
+ interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <0>;
+ fifo-size = <16>;
+ reg-io-width = <1>;
+ current-speed = <115200>;
+ no-loopback-test;
+ status = "disabled";
+ clocks = <&sysclk>;
+ resets = <&reset RESET_UART1>;
+ };
+
+ uart1: serial at 300000 {
+ compatible = "ns16550a";
+ reg = <0x200000 0x100000>;
+ interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <0>;
+ fifo-size = <16>;
+ reg-io-width = <1>;
+ current-speed = <115200>;
+ no-loopback-test;
+ status = "disabled";
+ clocks = <&sysclk>;
+ resets = <&reset RESET_UART2>;
+ };
+
+ rps at 400000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ ranges = <0 0x400000 0x100000>;
+
+ intc: interrupt-controller at 0 {
+ compatible = "oxsemi,ox820-rps-irq", "oxsemi,ox810se-rps-irq";
+ interrupt-controller;
+ reg = <0 0x200>;
+ interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+ #interrupt-cells = <1>;
+ valid-mask = <0xFFFFFFFF>;
+ clear-mask = <0>;
+ };
+
+ timer0: timer at 200 {
+ compatible = "oxsemi,ox820-rps-timer";
+ reg = <0x200 0x40>;
+ clocks = <&sysclk>;
+ interrupt-parent = <&intc>;
+ interrupts = <4>;
+ };
+ };
+
+ sys: sys-ctrl at e00000 {
+ compatible = "oxsemi,ox820-sys-ctrl", "syscon", "simple-mfd";
+ reg = <0xe00000 0x200000>;
+
+ reset: reset-controller {
+ compatible = "oxsemi,ox820-reset", "oxsemi,ox810se-reset";
+ #reset-cells = <1>;
+ };
+
+ stdclk: stdclk {
+ compatible = "oxsemi,ox820-stdclk", "oxsemi,ox810se-stdclk";
+ #clock-cells = <1>;
+ };
+ };
+ };
+
+ apb-bridge at 47000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ ranges = <0 0x47000000 0x1000000>;
+
+ scu: scu at 0 {
+ compatible = "arm,arm11mp-scu";
+ reg = <0x0 0x100>;
+ };
+
+ local-timer at 600 {
+ compatible = "arm,arm11mp-twd-timer";
+ reg = <0x600 0x20>;
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3)|IRQ_TYPE_LEVEL_HIGH)>;
+ clocks = <&armclk>;
+ };
+
+ gic: gic at 1000 {
+ compatible = "arm,arm11mp-gic";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ reg = <0x1000 0x1000>,
+ <0x100 0x500>;
+ };
+ };
+ };
+};
--
2.7.0
More information about the linux-arm-kernel
mailing list