[linux-sunxi] Re: [RFC PATCH] ARM: dts: sun8i: add simplefb node for H3

[Jernej Škrabec]

Dne četrtek, 01. december 2016 ob 03:03:14 CET je Icenowy Zheng napisal(a):
> 2016年12月1日 02:49于 Jernej Skrabec <jernej.skrabec at gmail.com>写道：
> 
> > Hi Jean-François,
> > 
> > Dne sreda, 30. november 2016 10.35.08 UTC+1 je oseba Jean-François Moine 
napisala:
> >> On Tue, 29 Nov 2016 22:59:32 +0100
> >> 
> >> Maxime Ripard <maxime... at free-electrons.com> wrote:
> >> > > > I'm still not sure which pipeline should I use.
> >> > > > 
> >> > > > And, it seems that HDMI Slow Clock is not needed?
> >> > > > 
> >> > > > (seems that it's only for EDID, but simplefb won't use EDID)
> >> > > 
> >> > > So, I don't see how this may work.
> >> > > How can the u-boot know the resolutions of the HDMI display device?
> >> > > 
> >> > > In other words: I have a new H3 board with the last u-boot and
> >> > > kernel.
> >> > > I plug my (rather old or brand new) HDMI display device.
> >> > > After powering on the system, I hope to get something on the screen.
> >> > > How?
> >> > 
> >> > If it works like the driver for the first display engine in U-Boot, it
> >> > will use the preferred mode reported by the EDID, and will fallback to
> >> > 1024x768 if it cannot access it.
> >> 
> >> Icenowy wrote: "simplefb won't use EDID"
> >> 
> >> Then, if it is like in the kernel, the 1024x768 mode is VGA. It does
> >> not work with HDMI (different timings).
> > 
> > U-Boot driver now accept any timings recommended by EDID. So far it
> > was tested with at least following resolutions:
> > - 1920x1080 @ 60 Hz
> > - 1280x1024 @ 60 Hz
> > - 1280x800 @ 60 Hz (slight clock difference)
> > - 800x480 (not sure about frame rate)
> > - 3840x2160 @ 30 Hz (4K)
> 
> I tested on 1024x600 (If my memory is right, it's @ 60Hz)
> 
> > and nobody complained so far. I'm pretty sure 1024x768 would work.
> > 
> >> > Maybe it would be worth exchanging on the EDID code that has been done
> >> > for the u-boot driver too, so that it can be fixed in your driver.
> >> 
> >> The u-boot got my code, and, up to now, I could not fix the random or
> >> permanent failures of EDID reading in some boards.
> > 
> > I only have one OPi2, but as I said, EDID always worked for me. The only
> > code left from you is for DE2. HDMI stuff is basically copied from Rockhip
> > driver (including EDID reading), TCON code is now reverted to the same as
> > it is in sunxi_display.c. I think it is worth to take a look at EDID code
> > and compare it.
> 
> So is the TCON of DE 2.0 identical to the original TCON?
> 
> If so, we should reuse sun4i-tcon ...
> 

Well, TCON is splitted in two parts (two base addresses), one for HDMI and one 
for TV. However, register offsets are same as before, so I guess driver 
reusage make sense. I think that there are few additional registers, but they 
can be ignored for simplefb.

> >  
> > 
> >> --
> >> Ken ar c'hentañ        |              ** Breizh ha Linux atav! **
> >> Jef                |                http://moinejf.free.fr/
> > 
> > Best regards,
> > Jernej Škrabec
> > 
> > --
> > You received this message because you are subscribed to the Google Groups
> > "linux-sunxi" group. To unsubscribe from this group and stop receiving
> > emails from it, send an email to
> > linux-sunxi+unsubscribe at googlegroups.com. For more options, visit
> > https://groups.google.com/d/optout.

Best regards,
Jernej Škrabec