[PATCH v3] ARM: at91/dt: add dts file for sama5d36ek CMP board
Nicolas Ferre
nicolas.ferre at atmel.com
Mon Nov 21 03:23:52 PST 2016
Le 21/11/2016 à 06:14, Wenyou Yang a écrit :
> The sama5d36ek CMP board is the variant of sama5d3xek board.
> It is equipped with the low-power DDR2 SDRAM, PMIC ACT8865 and
> some power rail. Its main purpose is used to measure the power
> consumption.
> The difference of the sama5d36ek CMP dts from sama5d36ek dts is
> listed as below.
> 1. The USB host nodes are removed, that is, the USB host is disabled.
> 2. The gpio_keys node is added to wake up from the sleep.
> 3. The LCD isn't supported due to the pins for LCD are conflicted
> with gpio_keys.
> 4. The adc0 node support the pinctrl sleep state to fix the over
> consumption on VDDANA.
>
> As said in errata, "When the USB host ports are used in high speed
> mode (EHCI), it is not possible to suspend the ports if no device is
> attached on each port. This leads to increased power consumption even
> if the system is in a low power mode." That is why the the USB host
> is disabled.
>
> Signed-off-by: Wenyou Yang <wenyou.yang at atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre at atmel.com>
Thanks Wenyou.
Regards,
> ---
>
> Changes in v3:
> - Use a dual license scheme for DT files.
> - Use the proper model name and the compatible string to reflect
> the nature of this new "CMP" board.
> - Change name of wakeup property to "wakeup-source".
> - Remove unnecessary comments.
> - Remove bootargs.
>
> Changes in v2:
> - Add the pinctrl sleep state for adc0 node to fix the over
> consumption on VDDANA.
> - Improve the commit log.
>
> arch/arm/boot/dts/sama5d36ek_cmp.dts | 87 ++++++++++
> arch/arm/boot/dts/sama5d3xcm_cmp.dtsi | 201 +++++++++++++++++++++++
> arch/arm/boot/dts/sama5d3xmb_cmp.dtsi | 301 ++++++++++++++++++++++++++++++++++
> 3 files changed, 589 insertions(+)
> create mode 100644 arch/arm/boot/dts/sama5d36ek_cmp.dts
> create mode 100644 arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
> create mode 100644 arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
>
> diff --git a/arch/arm/boot/dts/sama5d36ek_cmp.dts b/arch/arm/boot/dts/sama5d36ek_cmp.dts
> new file mode 100644
> index 0000000..b632143
> --- /dev/null
> +++ b/arch/arm/boot/dts/sama5d36ek_cmp.dts
> @@ -0,0 +1,87 @@
> +/*
> + * sama5d36ek_cmp.dts - Device Tree file for SAMA5D36-EK CMP board
> + *
> + * Copyright (C) 2016 Atmel,
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +/dts-v1/;
> +#include "sama5d36.dtsi"
> +#include "sama5d3xmb_cmp.dtsi"
> +
> +/ {
> + model = "Atmel SAMA5D36EK-CMP";
> + compatible = "atmel,sama5d36ek-cmp", "atmel,sama5d3xmb-cmp", "atmel,sama5d3xcm-cmp", "atmel,sama5d36", "atmel,sama5d3", "atmel,sama5";
> +
> + ahb {
> + apb {
> + spi0: spi at f0004000 {
> + status = "okay";
> + };
> +
> + ssc0: ssc at f0008000 {
> + status = "okay";
> + };
> +
> + can0: can at f000c000 {
> + status = "okay";
> + };
> +
> + i2c0: i2c at f0014000 {
> + status = "okay";
> + };
> +
> + i2c1: i2c at f0018000 {
> + status = "okay";
> + };
> +
> + macb0: ethernet at f0028000 {
> + status = "okay";
> + };
> +
> + macb1: ethernet at f802c000 {
> + status = "okay";
> + };
> + };
> + };
> +
> + sound {
> + status = "okay";
> + };
> +};
> diff --git a/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi b/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
> new file mode 100644
> index 0000000..dc7572b
> --- /dev/null
> +++ b/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
> @@ -0,0 +1,201 @@
> +/*
> + * sama5d3xcm_cmp.dtsi - Device Tree Include file for SAMA5D36 CMP CPU Module
> + *
> + * Copyright (C) 2016 Atmel,
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/ {
> + compatible = "atmel,sama5d3xcm-cmp", "atmel,sama5d3", "atmel,sama5";
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + memory {
> + reg = <0x20000000 0x20000000>;
> + };
> +
> + clocks {
> + slow_xtal {
> + clock-frequency = <32768>;
> + };
> +
> + main_xtal {
> + clock-frequency = <12000000>;
> + };
> + };
> +
> + ahb {
> + apb {
> + spi0: spi at f0004000 {
> + cs-gpios = <&pioD 13 0>, <0>, <0>, <0>;
> + };
> +
> + macb0: ethernet at f0028000 {
> + phy-mode = "rgmii";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethernet-phy at 1 {
> + reg = <0x1>;
> + interrupt-parent = <&pioB>;
> + interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> + txen-skew-ps = <800>;
> + txc-skew-ps = <3000>;
> + rxdv-skew-ps = <400>;
> + rxc-skew-ps = <3000>;
> + rxd0-skew-ps = <400>;
> + rxd1-skew-ps = <400>;
> + rxd2-skew-ps = <400>;
> + rxd3-skew-ps = <400>;
> + };
> +
> + ethernet-phy at 7 {
> + reg = <0x7>;
> + interrupt-parent = <&pioB>;
> + interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> + txen-skew-ps = <800>;
> + txc-skew-ps = <3000>;
> + rxdv-skew-ps = <400>;
> + rxc-skew-ps = <3000>;
> + rxd0-skew-ps = <400>;
> + rxd1-skew-ps = <400>;
> + rxd2-skew-ps = <400>;
> + rxd3-skew-ps = <400>;
> + };
> + };
> +
> + i2c1: i2c at f0018000 {
> + pmic: act8865 at 5b {
> + compatible = "active-semi,act8865";
> + reg = <0x5b>;
> + status = "disabled";
> +
> + regulators {
> + vcc_1v8_reg: DCDC_REG1 {
> + regulator-name = "VCC_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + vcc_1v2_reg: DCDC_REG2 {
> + regulator-name = "VCC_1V2";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-always-on;
> + };
> +
> + vcc_3v3_reg: DCDC_REG3 {
> + regulator-name = "VCC_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vddana_reg: LDO_REG1 {
> + regulator-name = "VDDANA";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vddfuse_reg: LDO_REG2 {
> + regulator-name = "FUSE_2V5";
> + regulator-min-microvolt = <2500000>;
> + regulator-max-microvolt = <2500000>;
> + };
> + };
> + };
> + };
> + };
> +
> + nand0: nand at 60000000 {
> + nand-bus-width = <8>;
> + nand-ecc-mode = "hw";
> + atmel,has-pmecc;
> + atmel,pmecc-cap = <4>;
> + atmel,pmecc-sector-size = <512>;
> + nand-on-flash-bbt;
> + status = "okay";
> +
> + at91bootstrap at 0 {
> + label = "at91bootstrap";
> + reg = <0x0 0x40000>;
> + };
> +
> + bootloader at 40000 {
> + label = "bootloader";
> + reg = <0x40000 0x80000>;
> + };
> +
> + bootloaderenv at c0000 {
> + label = "bootloader env";
> + reg = <0xc0000 0xc0000>;
> + };
> +
> + dtb at 180000 {
> + label = "device tree";
> + reg = <0x180000 0x80000>;
> + };
> +
> + kernel at 200000 {
> + label = "kernel";
> + reg = <0x200000 0x600000>;
> + };
> +
> + rootfs at 800000 {
> + label = "rootfs";
> + reg = <0x800000 0x0f800000>;
> + };
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + d2 {
> + label = "d2";
> + gpios = <&pioE 25 GPIO_ACTIVE_LOW>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +};
> diff --git a/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi b/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
> new file mode 100644
> index 0000000..252e0d3
> --- /dev/null
> +++ b/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
> @@ -0,0 +1,301 @@
> +/*
> + * sama5d3xmb_cmp.dts - Device Tree file for SAMA5D3x CMP mother board
> + *
> + * Copyright (C) 2016 Atmel,
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +#include "sama5d3xcm_cmp.dtsi"
> +
> +/ {
> + compatible = "atmel,sama5d3xmb-cmp", "atmel,sama5d3xcm-cmp", "atmel,sama5d3", "atmel,sama5";
> +
> + ahb {
> + apb {
> + mmc0: mmc at f0000000 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
> + status = "okay";
> + slot at 0 {
> + reg = <0>;
> + bus-width = <4>;
> + cd-gpios = <&pioD 17 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + spi0: spi at f0004000 {
> + dmas = <0>, <0>; /* Do not use DMA for spi0 */
> +
> + m25p80 at 0 {
> + compatible = "atmel,at25df321a";
> + spi-max-frequency = <50000000>;
> + reg = <0>;
> + };
> + };
> +
> + ssc0: ssc at f0008000 {
> + atmel,clk-from-rk-pin;
> + };
> +
> + /*
> + * i2c0 conflicts with ISI:
> + * disable it to allow the use of ISI
> + * can not enable audio when i2c0 disabled
> + */
> + i2c0: i2c at f0014000 {
> + wm8904: wm8904 at 1a {
> + compatible = "wlf,wm8904";
> + reg = <0x1a>;
> + clocks = <&pck0>;
> + clock-names = "mclk";
> + };
> + };
> +
> + i2c1: i2c at f0018000 {
> + ov2640: camera at 0x30 {
> + compatible = "ovti,ov2640";
> + reg = <0x30>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pck1_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
> + resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>;
> + pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>;
> + /* use pck1 for the master clock of ov2640 */
> + clocks = <&pck1>;
> + clock-names = "xvclk";
> + assigned-clocks = <&pck1>;
> + assigned-clock-rates = <25000000>;
> +
> + port {
> + ov2640_0: endpoint {
> + remote-endpoint = <&isi_0>;
> + bus-width = <8>;
> + };
> + };
> + };
> + };
> +
> + usart1: serial at f0020000 {
> + dmas = <0>, <0>; /* Do not use DMA for usart1 */
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
> + status = "okay";
> + };
> +
> + isi: isi at f0034000 {
> + port {
> + isi_0: endpoint {
> + remote-endpoint = <&ov2640_0>;
> + bus-width = <8>;
> + vsync-active = <1>;
> + hsync-active = <1>;
> + };
> + };
> + };
> +
> + mmc1: mmc at f8000000 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
> + status = "okay";
> + slot at 0 {
> + reg = <0>;
> + bus-width = <4>;
> + cd-gpios = <&pioD 18 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + adc0: adc at f8018000 {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <
> + &pinctrl_adc0_adtrg
> + &pinctrl_adc0_ad0
> + &pinctrl_adc0_ad1
> + &pinctrl_adc0_ad2
> + &pinctrl_adc0_ad3
> + &pinctrl_adc0_ad4
> + >;
> + pinctrl-1 = <
> + &pinctrl_adc0_adtrg_sleep
> + &pinctrl_adc0_ad0_sleep
> + &pinctrl_adc0_ad1_sleep
> + &pinctrl_adc0_ad2_sleep
> + &pinctrl_adc0_ad3_sleep
> + &pinctrl_adc0_ad4_sleep
> + >;
> + status = "okay";
> + };
> +
> + macb1: ethernet at f802c000 {
> + phy-mode = "rmii";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + phy0: ethernet-phy at 1 {
> + /*interrupt-parent = <&pioE>;*/
> + /*interrupts = <30 IRQ_TYPE_EDGE_FALLING>;*/
> + reg = <1>;
> + };
> + };
> +
> + pinctrl at fffff200 {
> + adc0 {
> + pinctrl_adc0_adtrg_sleep: adc0_adtrg_1 {
> + atmel,pins =
> + <AT91_PIOD 19 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>;
> + };
> + pinctrl_adc0_ad0_sleep: adc0_ad0_1 {
> + atmel,pins =
> + <AT91_PIOD 20 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>;
> + };
> + pinctrl_adc0_ad1_sleep: adc0_ad1_1 {
> + atmel,pins =
> + <AT91_PIOD 21 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>;
> + };
> + pinctrl_adc0_ad2_sleep: adc0_ad2_1 {
> + atmel,pins =
> + <AT91_PIOD 22 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>;
> + };
> + pinctrl_adc0_ad3_sleep: adc0_ad3_1 {
> + atmel,pins =
> + <AT91_PIOD 23 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>;
> + };
> + pinctrl_adc0_ad4_sleep: adc0_ad4_1 {
> + atmel,pins =
> + <AT91_PIOD 24 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>;
> + };
> + };
> +
> + board {
> + pinctrl_gpio_keys: gpio_keys {
> + atmel,pins =
> + <AT91_PIOE 27 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
> + };
> +
> + pinctrl_mmc0_cd: mmc0_cd {
> + atmel,pins =
> + <AT91_PIOD 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
> + };
> +
> + pinctrl_mmc1_cd: mmc1_cd {
> + atmel,pins =
> + <AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
> + };
> +
> + pinctrl_pck0_as_audio_mck: pck0_as_audio_mck {
> + atmel,pins =
> + <AT91_PIOD 30 AT91_PERIPH_B AT91_PINCTRL_NONE>;
> + };
> +
> + pinctrl_pck1_as_isi_mck: pck1_as_isi_mck-0 {
> + atmel,pins =
> + <AT91_PIOD 31 AT91_PERIPH_B AT91_PINCTRL_NONE>;
> + };
> +
> + pinctrl_sensor_reset: sensor_reset-0 {
> + atmel,pins =
> + <AT91_PIOE 24 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
> + };
> +
> + pinctrl_sensor_power: sensor_power-0 {
> + atmel,pins =
> + <AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
> + };
> +
> + pinctrl_usba_vbus: usba_vbus {
> + atmel,pins =
> + <AT91_PIOD 29 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
> + };
> + };
> + };
> +
> + dbgu: serial at ffffee00 {
> + dmas = <0>, <0>; /* Do not use DMA for dbgu */
> + status = "okay";
> + };
> +
> + watchdog at fffffe40 {
> + status = "okay";
> + };
> + };
> +
> + usb0: gadget at 00500000 {
> + atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usba_vbus>;
> + status = "okay";
> + };
> + };
> +
> + sound {
> + compatible = "atmel,asoc-wm8904";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pck0_as_audio_mck>;
> +
> + atmel,model = "wm8904 @ SAMA5D3EK";
> + atmel,audio-routing =
> + "Headphone Jack", "HPOUTL",
> + "Headphone Jack", "HPOUTR",
> + "IN2L", "Line In Jack",
> + "IN2R", "Line In Jack",
> + "Mic", "MICBIAS",
> + "IN1L", "Mic";
> +
> + atmel,ssc-controller = <&ssc0>;
> + atmel,audio-codec = <&wm8904>;
> +
> + status = "disabled";
> + };
> +
> + /* Conflict with LCD pins */
> + gpio_keys {
> + compatible = "gpio-keys";
> + status = "okay";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpio_keys>;
> +
> + pb_user1 {
> + label = "pb_user1";
> + gpios = <&pioE 27 GPIO_ACTIVE_HIGH>;
> + linux,code = <0x100>;
> + wakeup-source;
> + };
> + };
> +};
>
--
Nicolas Ferre
More information about the linux-arm-kernel
mailing list