[PATCH 1/2] ARM: dts: sun5i: Add touchscreen node to reference-design-tablet.dtsi

[Maxime Ripard]

Hi,

On Sun, Nov 13, 2016 at 08:22:02PM +0100, Hans de Goede wrote:
> Just like on sun8i all sun5i tablets use the same interrupt and power
> gpios for their touchscreens. I've checked all known a13 fex files and
> only the UTOO P66 uses a different gpio for the interrupt.
> 
> Add a touchscreen node to sun5i-reference-design-tablet.dtsi, which
> fills in the necessary gpios to avoid duplication in the tablet dts files,
> just like we do in sun8i-reference-design-tablet.dtsi.
> 
> This will make future patches adding touchscreen nodes to a13 tablets
> simpler.
> 
> Signed-off-by: Hans de Goede <hdegoede at redhat.com>
> ---
>  arch/arm/boot/dts/sun5i-a13-utoo-p66.dts           | 38 ++++++++--------------
>  .../boot/dts/sun5i-reference-design-tablet.dtsi    | 25 ++++++++++++++
>  2 files changed, 39 insertions(+), 24 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/sun5i-a13-utoo-p66.dts b/arch/arm/boot/dts/sun5i-a13-utoo-p66.dts
> index a8b0bcc..3d7ff10 100644
> --- a/arch/arm/boot/dts/sun5i-a13-utoo-p66.dts
> +++ b/arch/arm/boot/dts/sun5i-a13-utoo-p66.dts
> @@ -83,22 +83,6 @@
>  	allwinner,pins = "PG3";
>  };
>  
> -&i2c1 {
> -	icn8318: touchscreen at 40 {
> -		compatible = "chipone,icn8318";
> -		reg = <0x40>;
> -		interrupt-parent = <&pio>;
> -		interrupts = <6 9 IRQ_TYPE_EDGE_FALLING>; /* EINT9 (PG9) */
> -		pinctrl-names = "default";
> -		pinctrl-0 = <&ts_wake_pin_p66>;
> -		wake-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
> -		touchscreen-size-x = <800>;
> -		touchscreen-size-y = <480>;
> -		touchscreen-inverted-x;
> -		touchscreen-swapped-x-y;
> -	};
> -};
> -
>  &mmc2 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&mmc2_pins_a>;
> @@ -121,20 +105,26 @@
>  		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>  		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
>  	};
> -
> -	ts_wake_pin_p66: ts_wake_pin at 0 {
> -		allwinner,pins = "PB3";
> -		allwinner,function = "gpio_out";
> -		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> -		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> -	};
> -
>  };
>  
>  &reg_usb0_vbus {
>  	gpio = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
>  };
>  
> +&touchscreen {
> +	compatible = "chipone,icn8318";
> +	reg = <0x40>;
> +	/* The P66 uses a different EINT then the reference design */
> +	interrupts = <6 9 IRQ_TYPE_EDGE_FALLING>; /* EINT9 (PG9) */
> +	/* The icn8318 binding expects wake-gpios instead of power-gpios */
> +	wake-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
> +	touchscreen-size-x = <800>;
> +	touchscreen-size-y = <480>;
> +	touchscreen-inverted-x;
> +	touchscreen-swapped-x-y;
> +	status = "okay";
> +};
> +
>  &uart1 {
>  	/* The P66 uses the uart pins as gpios */
>  	status = "disabled";
> diff --git a/arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi b/arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi
> index 20cc940..7af488a 100644
> --- a/arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi
> +++ b/arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi
> @@ -41,6 +41,7 @@
>   */
>  #include "sunxi-reference-design-tablet.dtsi"
>  
> +#include <dt-bindings/interrupt-controller/irq.h>
>  #include <dt-bindings/pwm/pwm.h>
>  
>  / {
> @@ -84,6 +85,23 @@
>  };
>  
>  &i2c1 {
> +	/*
> +	 * The gsl1680 is rated at 400KHz and it will not work reliable at
> +	 * 100KHz, this has been confirmed on multiple different q8 tablets.
> +	 * All other devices on this bus are also rated for 400KHz.
> +	 */
> +	clock-frequency = <400000>;
> +
> +	touchscreen: touchscreen {
> +		interrupt-parent = <&pio>;
> +		interrupts = <6 11 IRQ_TYPE_EDGE_FALLING>; /* EINT11 (PG11) */
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&ts_power_pin>;
> +		power-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
> +		/* Tablet dts must provide reg and compatible */
> +		status = "disabled";
> +	};
> +
>  	pcf8563: rtc at 51 {
>  		compatible = "nxp,pcf8563";
>  		reg = <0x51>;
> @@ -125,6 +143,13 @@
>  		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
>  	};
>  
> +	ts_power_pin: ts_power_pin {
> +		allwinner,pins = "PB3";
> +		allwinner,function = "gpio_out";
> +		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +	};
> +

For the next release, we'll switch to the generic pin mux properties
("pins" and "function"), and we actually implemented the fact that the
drive and pull properties are optional, so you can drop them both.

You'll need next + http://lists.infradead.org/pipermail/linux-arm-kernel/2016-November/467123.html

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20161114/7e78a172/attachment.sig>