[PATCH v9 09/10] drm/mediatek: update DSI sub driver flow for sending commands to panel
YT Shen
yt.shen at mediatek.com
Fri Nov 11 03:55:45 PST 2016
This patch update enable/disable flow of DSI module and MIPI TX module.
Original flow works on there is a bridge chip: DSI -> bridge -> panel.
In this case: DSI -> panel, the DSI sub driver flow should be updated.
We need to initialize DSI first so that we can send commands to panel.
Signed-off-by: shaoming chen <shaoming.chen at mediatek.com>
Signed-off-by: YT Shen <yt.shen at mediatek.com>
---
drivers/gpu/drm/mediatek/mtk_dsi.c | 110 ++++++++++++++++++++++++++-------
drivers/gpu/drm/mediatek/mtk_mipi_tx.c | 32 +++++-----
2 files changed, 103 insertions(+), 39 deletions(-)
diff --git a/drivers/gpu/drm/mediatek/mtk_dsi.c b/drivers/gpu/drm/mediatek/mtk_dsi.c
index 860b84f..12a1206 100644
--- a/drivers/gpu/drm/mediatek/mtk_dsi.c
+++ b/drivers/gpu/drm/mediatek/mtk_dsi.c
@@ -94,6 +94,8 @@
#define DSI_RACK 0x84
#define RACK BIT(0)
+#define DSI_MEM_CONTI 0x90
+
#define DSI_PHY_LCCON 0x104
#define LC_HS_TX_EN BIT(0)
#define LC_ULPM_EN BIT(1)
@@ -126,6 +128,10 @@
#define CLK_HS_POST (0xff << 8)
#define CLK_HS_EXIT (0xff << 16)
+#define DSI_VM_CMD_CON 0x130
+#define VM_CMD_EN BIT(0)
+#define TS_VFP_EN BIT(5)
+
#define DSI_CMDQ0 0x180
#define CONFIG (0xff << 0)
#define SHORT_PACKET 0
@@ -219,12 +225,12 @@ static void mtk_dsi_phy_timconfig(struct mtk_dsi *dsi)
writel(timcon3, dsi->regs + DSI_PHY_TIMECON3);
}
-static void mtk_dsi_enable(struct mtk_dsi *dsi)
+static void mtk_dsi_engine_enable(struct mtk_dsi *dsi)
{
mtk_dsi_mask(dsi, DSI_CON_CTRL, DSI_EN, DSI_EN);
}
-static void mtk_dsi_disable(struct mtk_dsi *dsi)
+static void mtk_dsi_engine_disable(struct mtk_dsi *dsi)
{
mtk_dsi_mask(dsi, DSI_CON_CTRL, DSI_EN, 0);
}
@@ -249,7 +255,9 @@ static int mtk_dsi_poweron(struct mtk_dsi *dsi)
* mipi_ratio is mipi clk coefficient for balance the pixel clk in mipi.
* we set mipi_ratio is 1.05.
*/
- dsi->data_rate = dsi->vm.pixelclock * 3 * 21 / (1 * 1000 * 10);
+ dsi->data_rate = dsi->vm.pixelclock * 12 * 21;
+ dsi->data_rate /= (dsi->lanes * 1000 * 10);
+ dev_info(dev, "set mipitx's data rate: %dMHz\n", dsi->data_rate);
ret = clk_set_rate(dsi->hs_clk, dsi->data_rate * 1000000);
if (ret < 0) {
@@ -271,7 +279,7 @@ static int mtk_dsi_poweron(struct mtk_dsi *dsi)
goto err_disable_engine_clk;
}
- mtk_dsi_enable(dsi);
+ mtk_dsi_engine_enable(dsi);
mtk_dsi_reset_engine(dsi);
mtk_dsi_phy_timconfig(dsi);
@@ -289,7 +297,7 @@ static int mtk_dsi_poweron(struct mtk_dsi *dsi)
static void mtk_dsi_clk_ulp_mode_enter(struct mtk_dsi *dsi)
{
mtk_dsi_mask(dsi, DSI_PHY_LCCON, LC_HS_TX_EN, 0);
- mtk_dsi_mask(dsi, DSI_PHY_LCCON, LC_ULPM_EN, 0);
+ mtk_dsi_mask(dsi, DSI_PHY_LCCON, LC_ULPM_EN, LC_ULPM_EN);
}
static void mtk_dsi_clk_ulp_mode_leave(struct mtk_dsi *dsi)
@@ -302,7 +310,7 @@ static void mtk_dsi_clk_ulp_mode_leave(struct mtk_dsi *dsi)
static void mtk_dsi_lane0_ulp_mode_enter(struct mtk_dsi *dsi)
{
mtk_dsi_mask(dsi, DSI_PHY_LD0CON, LD0_HS_TX_EN, 0);
- mtk_dsi_mask(dsi, DSI_PHY_LD0CON, LD0_ULPM_EN, 0);
+ mtk_dsi_mask(dsi, DSI_PHY_LD0CON, LD0_ULPM_EN, LD0_ULPM_EN);
}
static void mtk_dsi_lane0_ulp_mode_leave(struct mtk_dsi *dsi)
@@ -338,11 +346,21 @@ static void mtk_dsi_set_mode(struct mtk_dsi *dsi)
if ((dsi->mode_flags & MIPI_DSI_MODE_VIDEO_BURST) &&
!(dsi->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE))
vid_mode = BURST_MODE;
+ else
+ vid_mode = SYNC_EVENT_MODE;
}
writel(vid_mode, dsi->regs + DSI_MODE_CTRL);
}
+static void mtk_dsi_set_vm_cmd(struct mtk_dsi *dsi)
+{
+ writel(0x3c, dsi->regs + DSI_MEM_CONTI);
+
+ mtk_dsi_mask(dsi, DSI_VM_CMD_CON, VM_CMD_EN, VM_CMD_EN);
+ mtk_dsi_mask(dsi, DSI_VM_CMD_CON, TS_VFP_EN, TS_VFP_EN);
+}
+
static void mtk_dsi_ps_control_vact(struct mtk_dsi *dsi)
{
struct videomode *vm = &dsi->vm;
@@ -399,6 +417,9 @@ static void mtk_dsi_rxtx_control(struct mtk_dsi *dsi)
break;
}
+ tmp_reg |= (dsi->mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS) << 6;
+ tmp_reg |= (dsi->mode_flags & MIPI_DSI_MODE_EOT_PACKET) >> 3;
+
writel(tmp_reg, dsi->regs + DSI_TXRX_CTRL);
}
@@ -477,6 +498,16 @@ static void mtk_dsi_start(struct mtk_dsi *dsi)
writel(1, dsi->regs + DSI_START);
}
+static void mtk_dsi_stop(struct mtk_dsi *dsi)
+{
+ writel(0, dsi->regs + DSI_START);
+}
+
+static void mtk_dsi_set_cmd_mode(struct mtk_dsi *dsi)
+{
+ writel(CMD_MODE, dsi->regs + DSI_MODE_CTRL);
+}
+
static void mtk_dsi_set_interrupt_enable(struct mtk_dsi *dsi)
{
u32 inten = LPRX_RD_RDY_INT_FLAG | CMD_DONE_INT_FLAG | VM_DONE_INT_FLAG;
@@ -506,7 +537,7 @@ static s32 mtk_dsi_wait_for_irq_done(struct mtk_dsi *dsi, u32 irq_flag,
if (ret == 0) {
dev_info(dsi->dev, "Wait DSI IRQ(0x%08x) Timeout\n", irq_flag);
- mtk_dsi_enable(dsi);
+ mtk_dsi_engine_enable(dsi);
mtk_dsi_reset_engine(dsi);
}
@@ -535,6 +566,17 @@ static irqreturn_t mtk_dsi_irq(int irq, void *dev_id)
return IRQ_HANDLED;
}
+static s32 mtk_dsi_switch_to_cmd_mode(struct mtk_dsi *dsi, u8 irq_flag, u32 t)
+{
+ mtk_dsi_irq_data_clear(dsi, irq_flag);
+ mtk_dsi_set_cmd_mode(dsi);
+
+ if (!mtk_dsi_wait_for_irq_done(dsi, irq_flag, t))
+ return -1;
+ else
+ return 0;
+}
+
static void mtk_dsi_poweroff(struct mtk_dsi *dsi)
{
if (WARN_ON(dsi->refcount == 0))
@@ -543,11 +585,6 @@ static void mtk_dsi_poweroff(struct mtk_dsi *dsi)
if (--dsi->refcount != 0)
return;
- mtk_dsi_lane0_ulp_mode_enter(dsi);
- mtk_dsi_clk_ulp_mode_enter(dsi);
-
- mtk_dsi_disable(dsi);
-
clk_disable_unprepare(dsi->engine_clk);
clk_disable_unprepare(dsi->digital_clk);
@@ -561,35 +598,45 @@ static void mtk_output_dsi_enable(struct mtk_dsi *dsi)
if (dsi->enabled)
return;
- if (dsi->panel) {
- if (drm_panel_prepare(dsi->panel)) {
- DRM_ERROR("failed to setup the panel\n");
- return;
- }
- }
-
ret = mtk_dsi_poweron(dsi);
if (ret < 0) {
DRM_ERROR("failed to power on dsi\n");
return;
}
+ usleep_range(20000, 21000);
+
mtk_dsi_rxtx_control(dsi);
+ mtk_dsi_phy_timconfig(dsi);
+ mtk_dsi_ps_control_vact(dsi);
+ mtk_dsi_set_vm_cmd(dsi);
+ mtk_dsi_config_vdo_timing(dsi);
+ mtk_dsi_set_interrupt_enable(dsi);
+ mtk_dsi_engine_enable(dsi);
mtk_dsi_clk_ulp_mode_leave(dsi);
mtk_dsi_lane0_ulp_mode_leave(dsi);
mtk_dsi_clk_hs_mode(dsi, 0);
- mtk_dsi_set_mode(dsi);
- mtk_dsi_ps_control_vact(dsi);
- mtk_dsi_config_vdo_timing(dsi);
- mtk_dsi_set_interrupt_enable(dsi);
+ if (dsi->panel) {
+ if (drm_panel_prepare(dsi->panel)) {
+ DRM_ERROR("failed to prepare the panel\n");
+ return;
+ }
+ }
mtk_dsi_set_mode(dsi);
mtk_dsi_clk_hs_mode(dsi, 1);
mtk_dsi_start(dsi);
+ if (dsi->panel) {
+ if (drm_panel_enable(dsi->panel)) {
+ DRM_ERROR("failed to enable the panel\n");
+ return;
+ }
+ }
+
dsi->enabled = true;
}
@@ -605,6 +652,21 @@ static void mtk_output_dsi_disable(struct mtk_dsi *dsi)
}
}
+ mtk_dsi_stop(dsi);
+ mtk_dsi_switch_to_cmd_mode(dsi, VM_DONE_INT_FLAG, 500);
+
+ if (dsi->panel) {
+ if (drm_panel_unprepare(dsi->panel)) {
+ DRM_ERROR("failed to unprepare the panel\n");
+ return;
+ }
+ }
+
+ mtk_dsi_reset_engine(dsi);
+ mtk_dsi_lane0_ulp_mode_enter(dsi);
+ mtk_dsi_clk_ulp_mode_enter(dsi);
+ mtk_dsi_engine_disable(dsi);
+
mtk_dsi_poweroff(dsi);
dsi->enabled = false;
@@ -845,7 +907,7 @@ static void mtk_dsi_wait_for_idle(struct mtk_dsi *dsi)
if (timeout_ms == 0) {
dev_info(dsi->dev, "polling dsi wait not busy timeout!\n");
- mtk_dsi_enable(dsi);
+ mtk_dsi_engine_enable(dsi);
mtk_dsi_reset_engine(dsi);
}
}
diff --git a/drivers/gpu/drm/mediatek/mtk_mipi_tx.c b/drivers/gpu/drm/mediatek/mtk_mipi_tx.c
index 108d31a..34e95c6 100644
--- a/drivers/gpu/drm/mediatek/mtk_mipi_tx.c
+++ b/drivers/gpu/drm/mediatek/mtk_mipi_tx.c
@@ -177,7 +177,9 @@ static int mtk_mipi_tx_pll_prepare(struct clk_hw *hw)
dev_dbg(mipi_tx->dev, "prepare: %u Hz\n", mipi_tx->data_rate);
- if (mipi_tx->data_rate >= 500000000) {
+ if (mipi_tx->data_rate > 1250000000) {
+ return -EINVAL;
+ } else if (mipi_tx->data_rate >= 500000000) {
txdiv = 1;
txdiv0 = 0;
txdiv1 = 0;
@@ -201,6 +203,10 @@ static int mtk_mipi_tx_pll_prepare(struct clk_hw *hw)
return -EINVAL;
}
+ mtk_mipi_tx_update_bits(mipi_tx, MIPITX_DSI_TOP_CON,
+ RG_DSI_LNT_IMP_CAL_CODE | RG_DSI_LNT_HS_BIAS_EN,
+ (8 << 4) | RG_DSI_LNT_HS_BIAS_EN);
+
mtk_mipi_tx_update_bits(mipi_tx, MIPITX_DSI_BG_CON,
RG_DSI_VOUT_MSK |
RG_DSI_BG_CKEN | RG_DSI_BG_CORE_EN,
@@ -210,24 +216,18 @@ static int mtk_mipi_tx_pll_prepare(struct clk_hw *hw)
usleep_range(30, 100);
- mtk_mipi_tx_update_bits(mipi_tx, MIPITX_DSI_TOP_CON,
- RG_DSI_LNT_IMP_CAL_CODE | RG_DSI_LNT_HS_BIAS_EN,
- (8 << 4) | RG_DSI_LNT_HS_BIAS_EN);
-
- mtk_mipi_tx_set_bits(mipi_tx, MIPITX_DSI_CON,
- RG_DSI_CKG_LDOOUT_EN | RG_DSI_LDOCORE_EN);
+ mtk_mipi_tx_update_bits(mipi_tx, MIPITX_DSI_CON,
+ RG_DSI_CKG_LDOOUT_EN | RG_DSI_LDOCORE_EN,
+ RG_DSI_CKG_LDOOUT_EN | RG_DSI_LDOCORE_EN);
mtk_mipi_tx_update_bits(mipi_tx, MIPITX_DSI_PLL_PWR,
RG_DSI_MPPLL_SDM_PWR_ON |
RG_DSI_MPPLL_SDM_ISO_EN,
RG_DSI_MPPLL_SDM_PWR_ON);
- mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_DSI_PLL_CON0,
- RG_DSI_MPPLL_PLL_EN);
-
mtk_mipi_tx_update_bits(mipi_tx, MIPITX_DSI_PLL_CON0,
- RG_DSI_MPPLL_TXDIV0 | RG_DSI_MPPLL_TXDIV1 |
- RG_DSI_MPPLL_PREDIV,
+ RG_DSI_MPPLL_PREDIV | RG_DSI_MPPLL_TXDIV0 |
+ RG_DSI_MPPLL_TXDIV1 | RG_DSI_MPPLL_POSDIV,
(txdiv0 << 3) | (txdiv1 << 5));
/*
@@ -242,10 +242,12 @@ static int mtk_mipi_tx_pll_prepare(struct clk_hw *hw)
26000000);
writel(pcw, mipi_tx->regs + MIPITX_DSI_PLL_CON2);
- mtk_mipi_tx_set_bits(mipi_tx, MIPITX_DSI_PLL_CON1,
- RG_DSI_MPPLL_SDM_FRA_EN);
+ mtk_mipi_tx_update_bits(mipi_tx, MIPITX_DSI_PLL_CON1,
+ RG_DSI_MPPLL_SDM_FRA_EN,
+ RG_DSI_MPPLL_SDM_FRA_EN);
- mtk_mipi_tx_set_bits(mipi_tx, MIPITX_DSI_PLL_CON0, RG_DSI_MPPLL_PLL_EN);
+ mtk_mipi_tx_update_bits(mipi_tx, MIPITX_DSI_PLL_CON0,
+ RG_DSI_MPPLL_PLL_EN, RG_DSI_MPPLL_PLL_EN);
usleep_range(20, 100);
--
1.9.1
More information about the linux-arm-kernel
mailing list