[PATCH 1/2] arm64: dts: add USB1-related nodes of Allwinner A64

[Maxime Ripard]

On Sat, Nov 05, 2016 at 10:38:29PM +0800, Icenowy Zheng wrote:
> Allwinner A64 have two HCI USB controllers, a OTG controller and a USB
> PHY device which have two ports. One of the port is wired to both a HCI
> USB controller and the OTG controller, which is currently not supported.
> The another one is only wired to a HCI controller, and the device node of
> OHCI/EHCI controller of the port can be added now.
> 
> Also the A64 USB PHY device node is also added for the HCI controllers to
> work.
> 
> Signed-off-by: Icenowy Zheng <icenowy at aosc.xyz>
> ---
>  arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 50 +++++++++++++++++++++++++++
>  1 file changed, 50 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> index 3d70be3..c2b6dc8 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> @@ -259,5 +259,55 @@
>  			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
>  				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
>  		};
> +
> +		usbphy: phy at 01c19400 {
> +			compatible = "allwinner,sun50i-a64-usb-phy";
> +			reg = <0x01c19400 0x14>,
> +			      <0x01c1b800 0x4>;
> +			reg-names = "phy_ctrl",
> +				    "pmu1";
> +			clocks = <&ccu CLK_USB_PHY0>,
> +				 <&ccu CLK_USB_PHY1>;
> +			clock-names = "usb0_phy",
> +				      "usb1_phy";
> +			resets = <&ccu RST_USB_PHY0>,
> +				 <&ccu RST_USB_PHY1>;
> +			reset-names = "usb0_reset",
> +				      "usb1_reset";
> +			status = "disabled";
> +			#phy-cells = <1>;
> +		};
> +
> +		ohci1: usb at 01c1a400 {
> +			compatible = "allwinner,sun50i-a64-ohci", "generic-ohci";
> +			reg = <0x01c1b400 0x100>;
> +			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
> +			/*
> +			 * According to the user manual, OHCI1 USB clock
> +			 * depends on OHCI0 clock.
> +			 */

This is something that should be dealt with in the clock framework,
not in your driver.

> +			clocks = <&ccu CLK_BUS_OHCI1>,
> +				 <&ccu CLK_USB_OHCI0>,
> +				 <&ccu CLK_USB_OHCI1>;
> +			resets = <&ccu RST_BUS_OHCI1>;
> +			phys = <&usbphy 1>;
> +			phy-names = "usb";
> +			status = "disabled";
> +		};
> +
> +		ehci1: usb at 01c1a000 {
> +			compatible = "allwinner,sun50i-a64-ehci", "generic-ehci";
> +			reg = <0x01c1b000 0x100>;

And please order these nodes by base address.

Also, in both the ehci and ohci nodes, the unit-address and reg don't
match, which one is the right one?

Thanks,
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20161106/8451990e/attachment.sig>