[PATCH v2 4/6] pinctrl: aspeed: Read and write bits in LPCHC and GFX controllers
Joel Stanley
joel at jms.id.au
Thu Nov 3 16:24:23 PDT 2016
On Thu, Nov 3, 2016 at 1:07 AM, Andrew Jeffery <andrew at aj.id.au> wrote:
> The System Control Unit IP block in the Aspeed SoCs is typically where
> the pinmux configuration is found, but not always. A number of pins
> depend on state in one of LPC Host Control (LPCHC) or SoC Display
> Controller (GFX) IP blocks, so the Aspeed pinmux drivers should have the
> means to adjust these as necessary.
>
> We use syscon to cast a regmap over the GFX and LPCHCR blocks, which is
> used as an arbitration layer between the relevant driver and the pinctrl
> subsystem. The regmaps are then exposed to the SoC-specific pinctrl
> drivers by phandles in the devicetree, and are selected during a mux
> request by querying a new 'ip' member in struct aspeed_sig_desc.
>
> Signed-off-by: Andrew Jeffery <andrew at aj.id.au>
I like this a lot more than the first go. Good work.
Some minor comments below.
> ---
> Since v1:
>
> The change is now proactive: instead of reporting that we need to flip bits in
> controllers we can't access, the patch provides access via regmaps for the
> relevant controllers. The implementation also splits out the IP block ID into
> its own variable rather than packing the value into the upper bits of the reg
> member of struct aspeed_sig_desc. This drives some churn in the diff, but I've
> tried to minimise it.
>
> .../devicetree/bindings/pinctrl/pinctrl-aspeed.txt | 50 +++++++++++++---
> drivers/pinctrl/aspeed/pinctrl-aspeed-g4.c | 18 +++---
> drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c | 39 ++++++++++---
> drivers/pinctrl/aspeed/pinctrl-aspeed.c | 66 +++++++++++++---------
> drivers/pinctrl/aspeed/pinctrl-aspeed.h | 32 ++++++++---
> 5 files changed, 144 insertions(+), 61 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt
> index 2ad18c4ea55c..115b0cce6c1c 100644
> --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt
> +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt
> @@ -4,12 +4,19 @@ Aspeed Pin Controllers
> The Aspeed SoCs vary in functionality inside a generation but have a common mux
> device register layout.
>
> -Required properties:
> -- compatible : Should be any one of the following:
> - "aspeed,ast2400-pinctrl"
> - "aspeed,g4-pinctrl"
> - "aspeed,ast2500-pinctrl"
> - "aspeed,g5-pinctrl"
> +Required properties for g4:
> +- compatible : Should be any one of the following:
> + "aspeed,ast2400-pinctrl"
> + "aspeed,g4-pinctrl"
> +
> +Required properties for g5:
> +- compatible : Should be any one of the following:
> + "aspeed,ast2500-pinctrl"
> + "aspeed,g5-pinctrl"
> +
> +- aspeed,external-nodes: A cell of phandles to external controller nodes:
> + 0: compatible with "aspeed,ast2500-gfx", "syscon"
> + 1: compatible with "aspeed,ast2500-lpchc", "syscon"
>
> The pin controller node should be a child of a syscon node with the required
> property:
> @@ -47,7 +54,7 @@ RGMII1 RGMII2 RMII1 RMII2 SD1 SPI1 SPI1DEBUG SPI1PASSTHRU TIMER4 TIMER5 TIMER6
> TIMER7 TIMER8 VGABIOSROM
>
>
> -Examples:
> +g4 Example:
>
> syscon: scu at 1e6e2000 {
> compatible = "syscon", "simple-mfd";
> @@ -63,5 +70,34 @@ syscon: scu at 1e6e2000 {
> };
> };
>
> +g5 Example:
> +
> +apb {
> + gfx: display at 1e6e6000 {
> + compatible = "aspeed,ast2500-gfx", "syscon";
> + reg = <0x1e6e6000 0x1000>;
> + };
> +
> + lpchc: lpchc at 1e7890a0 {
> + compatible = "aspeed,ast2500-lpchc", "syscon";
> + reg = <0x1e7890a0 0xc4>;
> + };
> +
> + syscon: scu at 1e6e2000 {
> + compatible = "syscon", "simple-mfd";
> + reg = <0x1e6e2000 0x1a8>;
> +
> + pinctrl: pinctrl {
> + compatible = "aspeed,g5-pinctrl";
> + aspeed,external-nodes = <&gfx, &lpchc>;
> +
> + pinctrl_i2c3_default: i2c3_default {
> + function = "I2C3";
> + groups = "I2C3";
> + };
> + };
> + };
> +};
> +
> Please refer to pinctrl-bindings.txt in this directory for details of the
> common pinctrl bindings used by client devices.
> diff --git a/drivers/pinctrl/aspeed/pinctrl-aspeed-g4.c b/drivers/pinctrl/aspeed/pinctrl-aspeed-g4.c
> index a21b071ff290..558bd102416c 100644
> --- a/drivers/pinctrl/aspeed/pinctrl-aspeed-g4.c
> +++ b/drivers/pinctrl/aspeed/pinctrl-aspeed-g4.c
> @@ -292,7 +292,7 @@ SSSF_PIN_DECL(U18, GPIOG7, FLWP, SIG_DESC_SET(SCU84, 7));
> #define UART6_DESC SIG_DESC_SET(SCU90, 7)
> #define ROM16_DESC SIG_DESC_SET(SCU90, 6)
> #define FLASH_WIDE SIG_DESC_SET(HW_STRAP1, 4)
> -#define BOOT_SRC_NOR { HW_STRAP1, GENMASK(1, 0), 0, 0 }
> +#define BOOT_SRC_NOR { ASPEED_IP_SCU, HW_STRAP1, GENMASK(1, 0), 0, 0 }
>
> #define A8 56
> SIG_EXPR_DECL(ROMD8, ROM16, ROM16_DESC);
> @@ -418,9 +418,9 @@ FUNC_GROUP_DECL(I2C8, G5, F3);
> #define U1 88
> SSSF_PIN_DECL(U1, GPIOL0, NCTS1, SIG_DESC_SET(SCU84, 16));
>
> -#define VPI18_DESC { SCU90, GENMASK(5, 4), 1, 0 }
> -#define VPI24_DESC { SCU90, GENMASK(5, 4), 2, 0 }
> -#define VPI30_DESC { SCU90, GENMASK(5, 4), 3, 0 }
> +#define VPI18_DESC { ASPEED_IP_SCU, SCU90, GENMASK(5, 4), 1, 0 }
> +#define VPI24_DESC { ASPEED_IP_SCU, SCU90, GENMASK(5, 4), 2, 0 }
> +#define VPI30_DESC { ASPEED_IP_SCU, SCU90, GENMASK(5, 4), 3, 0 }
>
> #define T5 89
> #define T5_DESC SIG_DESC_SET(SCU84, 17)
> @@ -641,11 +641,11 @@ SSSF_PIN_DECL(Y22, GPIOR2, ROMCS3, SIG_DESC_SET(SCU88, 26));
> #define U19 139
> SSSF_PIN_DECL(U19, GPIOR3, ROMCS4, SIG_DESC_SET(SCU88, 27));
>
> -#define VPOOFF0_DESC { SCU94, GENMASK(1, 0), 0, 0 }
> -#define VPO12_DESC { SCU94, GENMASK(1, 0), 1, 0 }
> -#define VPO24_DESC { SCU94, GENMASK(1, 0), 2, 0 }
> -#define VPOOFF1_DESC { SCU94, GENMASK(1, 0), 3, 0 }
> -#define VPO_OFF_12 { SCU94, 0x2, 0, 0 }
> +#define VPOOFF0_DESC { ASPEED_IP_SCU, SCU94, GENMASK(1, 0), 0, 0 }
> +#define VPO12_DESC { ASPEED_IP_SCU, SCU94, GENMASK(1, 0), 1, 0 }
> +#define VPO24_DESC { ASPEED_IP_SCU, SCU94, GENMASK(1, 0), 2, 0 }
> +#define VPOOFF1_DESC { ASPEED_IP_SCU, SCU94, GENMASK(1, 0), 3, 0 }
> +#define VPO_OFF_12 { ASPEED_IP_SCU, SCU94, 0x2, 0, 0 }
> #define VPO_24_OFF SIG_DESC_SET(SCU94, 1)
>
> #define V21 140
> diff --git a/drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c b/drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c
> index 87b46390b695..99c4fa9bf861 100644
> --- a/drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c
> +++ b/drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c
> @@ -10,6 +10,7 @@
> #include <linux/init.h>
> #include <linux/io.h>
> #include <linux/kernel.h>
> +#include <linux/mfd/syscon.h>
> #include <linux/mutex.h>
> #include <linux/of.h>
> #include <linux/platform_device.h>
> @@ -26,8 +27,8 @@
>
> #define ASPEED_G5_NR_PINS 228
>
> -#define COND1 { SCU90, BIT(6), 0, 0 }
> -#define COND2 { SCU94, GENMASK(1, 0), 0, 0 }
> +#define COND1 { ASPEED_IP_SCU, SCU90, BIT(6), 0, 0 }
> +#define COND2 { ASPEED_IP_SCU, SCU94, GENMASK(1, 0), 0, 0 }
>
> #define B14 0
> SSSF_PIN_DECL(B14, GPIOA0, MAC1LINK, SIG_DESC_SET(SCU80, 0));
> @@ -186,9 +187,12 @@ MS_PIN_DECL(C20, GPIOE1, NDCD3, GPIE0OUT);
>
> FUNC_GROUP_DECL(GPIE0, B20, C20);
>
> -#define SPI1_DESC { HW_STRAP1, GENMASK(13, 12), 1, 0 }
> -#define SPI1DEBUG_DESC { HW_STRAP1, GENMASK(13, 12), 2, 0 }
> -#define SPI1PASSTHRU_DESC { HW_STRAP1, GENMASK(13, 12), 3, 0 }
> +#define SPI1_DESC \
> + { ASPEED_IP_SCU, HW_STRAP1, GENMASK(13, 12), 1, 0 }
> +#define SPI1DEBUG_DESC \
> + { ASPEED_IP_SCU, HW_STRAP1, GENMASK(13, 12), 2, 0 }
> +#define SPI1PASSTHRU_DESC \
> + { ASPEED_IP_SCU, HW_STRAP1, GENMASK(13, 12), 3, 0 }
>
> #define C18 64
> SIG_EXPR_DECL(SYSCS, SPI1DEBUG, COND1, SPI1DEBUG_DESC);
> @@ -325,10 +329,11 @@ SS_PIN_DECL(R1, GPIOK7, SDA8);
>
> FUNC_GROUP_DECL(I2C8, P2, R1);
>
> -#define VPIOFF0_DESC { SCU90, GENMASK(5, 4), 0, 0 }
> -#define VPIOFF1_DESC { SCU90, GENMASK(5, 4), 1, 0 }
> -#define VPI24_DESC { SCU90, GENMASK(5, 4), 2, 0 }
> -#define VPIRSVD_DESC { SCU90, GENMASK(5, 4), 3, 0 }
> +#define VPIOFF0_DESC { ASPEED_IP_SCU, SCU90, GENMASK(5, 4), 0, 0 }
> +#define VPIOFF1_DESC { ASPEED_IP_SCU, SCU90, GENMASK(5, 4), 1, 0 }
> +#define VPI24_DESC { ASPEED_IP_SCU, SCU90, GENMASK(5, 4), 2, 0 }
> +#define VPIRSVD_DESC { ASPEED_IP_SCU, SCU90, GENMASK(5, 4), 3, 0 }
> +
>
> #define V2 104
> #define V2_DESC SIG_DESC_SET(SCU88, 0)
> @@ -848,10 +853,26 @@ static struct pinctrl_desc aspeed_g5_pinctrl_desc = {
> static int aspeed_g5_pinctrl_probe(struct platform_device *pdev)
> {
> int i;
> + struct regmap **map;
> + struct device_node *node;
>
> for (i = 0; i < ARRAY_SIZE(aspeed_g5_pins); i++)
> aspeed_g5_pins[i].number = i;
>
> + map = &aspeed_g5_pinctrl_data.maps[ASPEED_IP_GFX];
> + node = of_parse_phandle(pdev->dev.of_node, "aspeed,external-nodes", 0);
> + *map = syscon_node_to_regmap(node);
I think you can use syscon_regmap_lookup_by_phandle to replace both of
these lines.
> + of_node_put(node);
> + if (IS_ERR(*map))
> + return PTR_ERR(*map);
Do we want to fail, or warn and continue?
The sequence is a bit messy. How about:
struct regmap *map;
map = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
"aspeed,external-nodes");
if (IS_ERR(map))
return PTR_ERR(map);
aspeed_g5_pinctrl_data.maps[ASPEED_IP_GFX] = map;
> +
> + map = &aspeed_g5_pinctrl_data.maps[ASPEED_IP_LPCHC];
> + node = of_parse_phandle(pdev->dev.of_node, "aspeed,external-nodes", 1);
> + *map = syscon_node_to_regmap(node);
> + of_node_put(node);
> + if (IS_ERR(*map))
> + return PTR_ERR(*map);
> +
Same comments as above.
> return aspeed_pinctrl_probe(pdev, &aspeed_g5_pinctrl_desc,
> &aspeed_g5_pinctrl_data);
> }
> diff --git a/drivers/pinctrl/aspeed/pinctrl-aspeed.c b/drivers/pinctrl/aspeed/pinctrl-aspeed.c
> index 49aeba912531..23586aac7a5a 100644
> --- a/drivers/pinctrl/aspeed/pinctrl-aspeed.c
> +++ b/drivers/pinctrl/aspeed/pinctrl-aspeed.c
> @@ -14,6 +14,12 @@
> #include "../core.h"
> #include "pinctrl-aspeed.h"
>
> +static const char *const aspeed_pinmux_ips[] = {
> + [ASPEED_IP_SCU] = "SCU",
> + [ASPEED_IP_GFX] = "GFX",
> + [ASPEED_IP_LPCHC] = "LHCR",
We've got both LPCHC and LHCR here. As I said when commenting on the
regmap bindings, I like LHC(R) better.
> +};
> +
> int aspeed_pinctrl_get_groups_count(struct pinctrl_dev *pctldev)
> {
> struct aspeed_pinctrl_data *pdata = pinctrl_dev_get_drvdata(pctldev);
> @@ -78,7 +84,8 @@ int aspeed_pinmux_get_fn_groups(struct pinctrl_dev *pctldev,
> static inline void aspeed_sig_desc_print_val(
> const struct aspeed_sig_desc *desc, bool enable, u32 rv)
What's a rv? Perhaps "reg" or "value"?
> {
> - pr_debug("SCU%x[0x%08x]=0x%x, got 0x%x from 0x%08x\n", desc->reg,
> + pr_debug("Want %s%X[0x%08X]=0x%X, got 0x%X from 0x%08X\n",
> + aspeed_pinmux_ips[desc->ip], desc->reg,
> desc->mask, enable ? desc->enable : desc->disable,
> (rv & desc->mask) >> __ffs(desc->mask), rv);
> }
> @@ -88,7 +95,7 @@ static inline void aspeed_sig_desc_print_val(
> *
> * @desc: The signal descriptor of interest
> * @enabled: True to query the enabled state, false to query disabled state
> - * @regmap: The SCU regmap instance
> + * @regmap: The IP block's regmap instance
> *
> * @return True if the descriptor's bitfield is configured to the state
> * selected by @enabled, false otherwise
> @@ -119,7 +126,7 @@ static bool aspeed_sig_desc_eval(const struct aspeed_sig_desc *desc,
> *
> * @expr: An expression controlling the signal for a mux function on a pin
> * @enabled: True to query the enabled state, false to query disabled state
> - * @regmap: The SCU regmap instance
> + * @maps: The list of regmap instances
> *
> * @return True if the expression composed by @enabled evaluates true, false
> * otherwise
> @@ -136,15 +143,16 @@ static bool aspeed_sig_desc_eval(const struct aspeed_sig_desc *desc,
> * either condition as required.
> */
> static bool aspeed_sig_expr_eval(const struct aspeed_sig_expr *expr,
> - bool enabled, struct regmap *map)
> + bool enabled, struct regmap * const *maps)
> {
> int i;
>
> for (i = 0; i < expr->ndescs; i++) {
> const struct aspeed_sig_desc *desc = &expr->descs[i];
>
> - if (!aspeed_sig_desc_eval(desc, enabled, map))
> + if (!aspeed_sig_desc_eval(desc, enabled, maps[desc->ip]))
> return false;
> +
> }
>
> return true;
> @@ -158,12 +166,12 @@ static bool aspeed_sig_expr_eval(const struct aspeed_sig_expr *expr,
> * configured
> * @enable: true to enable an function's signal through a pin's signal
> * expression, false to disable the function's signal
> - * @map: The SCU's regmap instance for pinmux register access.
> + * @maps: The list of regmap instances for pinmux register access.
> *
> * @return true if the expression is configured as requested, false otherwise
> */
> static bool aspeed_sig_expr_set(const struct aspeed_sig_expr *expr,
> - bool enable, struct regmap *map)
> + bool enable, struct regmap * const *maps)
> {
> int i;
>
> @@ -171,6 +179,7 @@ static bool aspeed_sig_expr_set(const struct aspeed_sig_expr *expr,
> bool ret;
> const struct aspeed_sig_desc *desc = &expr->descs[i];
> u32 pattern = enable ? desc->enable : desc->disable;
> + u32 val = (pattern << __ffs(desc->mask));
>
> /*
> * Strap registers are configured in hardware or by early-boot
> @@ -179,48 +188,49 @@ static bool aspeed_sig_expr_set(const struct aspeed_sig_expr *expr,
> * deconfigured and is the reason we re-evaluate after writing
> * all descriptor bits.
> */
> - if (desc->reg == HW_STRAP1 || desc->reg == HW_STRAP2)
> + if ((desc->reg == HW_STRAP1 || desc->reg == HW_STRAP2) &&
> + desc->ip == ASPEED_IP_SCU)
> continue;
>
> - ret = regmap_update_bits(map, desc->reg, desc->mask,
> - pattern << __ffs(desc->mask)) == 0;
> + ret = regmap_update_bits(maps[desc->ip], desc->reg,
> + desc->mask, val) == 0;
>
> if (!ret)
> return ret;
> }
>
> - return aspeed_sig_expr_eval(expr, enable, map);
> + return aspeed_sig_expr_eval(expr, enable, maps);
> }
>
> static bool aspeed_sig_expr_enable(const struct aspeed_sig_expr *expr,
> - struct regmap *map)
> + struct regmap * const *maps)
> {
> - if (aspeed_sig_expr_eval(expr, true, map))
> + if (aspeed_sig_expr_eval(expr, true, maps))
> return true;
>
> - return aspeed_sig_expr_set(expr, true, map);
> + return aspeed_sig_expr_set(expr, true, maps);
> }
>
> static bool aspeed_sig_expr_disable(const struct aspeed_sig_expr *expr,
> - struct regmap *map)
> + struct regmap * const *maps)
> {
> - if (!aspeed_sig_expr_eval(expr, true, map))
> + if (!aspeed_sig_expr_eval(expr, true, maps))
> return true;
>
> - return aspeed_sig_expr_set(expr, false, map);
> + return aspeed_sig_expr_set(expr, false, maps);
> }
>
> /**
> * Disable a signal on a pin by disabling all provided signal expressions.
> *
> * @exprs: The list of signal expressions (from a priority level on a pin)
> - * @map: The SCU's regmap instance for pinmux register access.
> + * @maps: The list of regmap instances for pinmux register access.
> *
> * @return true if all expressions in the list are successfully disabled, false
> * otherwise
> */
> static bool aspeed_disable_sig(const struct aspeed_sig_expr **exprs,
> - struct regmap *map)
> + struct regmap * const *maps)
> {
> bool disabled = true;
>
> @@ -230,7 +240,7 @@ static bool aspeed_disable_sig(const struct aspeed_sig_expr **exprs,
> while (*exprs) {
> bool ret;
>
> - ret = aspeed_sig_expr_disable(*exprs, map);
> + ret = aspeed_sig_expr_disable(*exprs, maps);
> disabled = disabled && ret;
>
> exprs++;
> @@ -343,6 +353,8 @@ int aspeed_pinmux_set_mux(struct pinctrl_dev *pctldev, unsigned int function,
> const struct aspeed_sig_expr **funcs;
> const struct aspeed_sig_expr ***prios;
>
> + pr_debug("Muxing pin %d for %s\n", pin, pfunc->name);
> +
> if (!pdesc)
> return -EINVAL;
>
> @@ -358,7 +370,7 @@ int aspeed_pinmux_set_mux(struct pinctrl_dev *pctldev, unsigned int function,
> if (expr)
> break;
>
> - if (!aspeed_disable_sig(funcs, pdata->map))
> + if (!aspeed_disable_sig(funcs, pdata->maps))
> return -EPERM;
>
> prios++;
> @@ -377,7 +389,7 @@ int aspeed_pinmux_set_mux(struct pinctrl_dev *pctldev, unsigned int function,
> return -ENXIO;
> }
>
> - if (!aspeed_sig_expr_enable(expr, pdata->map))
> + if (!aspeed_sig_expr_enable(expr, pdata->maps))
> return -EPERM;
> }
>
> @@ -432,7 +444,7 @@ int aspeed_gpio_request_enable(struct pinctrl_dev *pctldev,
> if (aspeed_gpio_in_exprs(funcs))
> break;
>
> - if (!aspeed_disable_sig(funcs, pdata->map))
> + if (!aspeed_disable_sig(funcs, pdata->maps))
> return -EPERM;
>
> prios++;
> @@ -462,7 +474,7 @@ int aspeed_gpio_request_enable(struct pinctrl_dev *pctldev,
> * If GPIO is not the lowest priority signal type, assume there is only
> * one expression defined to enable the GPIO function
> */
> - if (!aspeed_sig_expr_enable(expr, pdata->map))
> + if (!aspeed_sig_expr_enable(expr, pdata->maps))
> return -EPERM;
>
> return 0;
> @@ -481,10 +493,10 @@ int aspeed_pinctrl_probe(struct platform_device *pdev,
> return -ENODEV;
> }
>
> - pdata->map = syscon_node_to_regmap(parent->of_node);
> - if (IS_ERR(pdata->map)) {
> + pdata->maps[ASPEED_IP_SCU] = syscon_node_to_regmap(parent->of_node);
> + if (IS_ERR(pdata->maps[ASPEED_IP_SCU])) {
> dev_err(&pdev->dev, "No regmap for syscon pincontroller parent\n");
> - return PTR_ERR(pdata->map);
> + return PTR_ERR(pdata->maps[ASPEED_IP_SCU]);
> }
>
> pctl = pinctrl_register(pdesc, &pdev->dev, pdata);
> diff --git a/drivers/pinctrl/aspeed/pinctrl-aspeed.h b/drivers/pinctrl/aspeed/pinctrl-aspeed.h
> index 3e72ef8c54bf..727728b86c07 100644
> --- a/drivers/pinctrl/aspeed/pinctrl-aspeed.h
> +++ b/drivers/pinctrl/aspeed/pinctrl-aspeed.h
> @@ -232,6 +232,11 @@
> * group.
> */
>
> +#define ASPEED_IP_SCU 0
> +#define ASPEED_IP_GFX 1
> +#define ASPEED_IP_LPCHC 2
> +#define ASPEED_NR_PINMUX_IPS 3
> +
> /*
> * The "Multi-function Pins Mapping and Control" table in the SoC datasheet
> * references registers by the device/offset mnemonic. The register macros
> @@ -261,7 +266,9 @@
> * A signal descriptor, which describes the register, bits and the
> * enable/disable values that should be compared or written.
> *
> - * @reg: The register offset from base in bytes
> + * @ip: The IP block identifier, used as an index into the regmap array in
> + * struct aspeed_pinctrl_data
> + * @reg: The register offset with respect to the base address of the IP block
> * @mask: The mask to apply to the register. The lowest set bit of the mask is
> * used to derive the shift value.
> * @enable: The value that enables the function. Value should be in the LSBs,
> @@ -270,6 +277,7 @@
> * LSBs, not at the position of the mask.
> */
> struct aspeed_sig_desc {
> + unsigned int ip;
> unsigned int reg;
> u32 mask;
> u32 enable;
> @@ -313,24 +321,30 @@ struct aspeed_pin_desc {
>
> /* Macro hell */
>
> +#define SIG_DESC_IP_BIT(ip, reg, idx, val) \
> + { ip, reg, BIT_MASK(idx), val, (((val) + 1) & 1) }
> +
> /**
> - * Short-hand macro for describing a configuration enabled by the state of one
> - * bit. The disable value is derived.
> + * Short-hand macro for describing an SCU descriptor enabled by the state of
> + * one bit. The disable value is derived.
> *
> * @reg: The signal's associated register, offset from base
> * @idx: The signal's bit index in the register
> * @val: The value (0 or 1) that enables the function
> */
> #define SIG_DESC_BIT(reg, idx, val) \
> - { reg, BIT_MASK(idx), val, (((val) + 1) & 1) }
> + SIG_DESC_IP_BIT(ASPEED_IP_SCU, reg, idx, val)
> +
> +#define SIG_DESC_IP_SET(ip, reg, idx) SIG_DESC_IP_BIT(ip, reg, idx, 1)
>
> /**
> - * A further short-hand macro describing a configuration enabled with a set bit.
> + * A further short-hand macro expanding to an SCU descriptor enabled by a set
> + * bit.
> *
> - * @reg: The configuration's associated register, offset from base
> - * @idx: The configuration's bit index in the register
> + * @reg: The register, offset from base
> + * @idx: The bit index in the register
> */
> -#define SIG_DESC_SET(reg, idx) SIG_DESC_BIT(reg, idx, 1)
> +#define SIG_DESC_SET(reg, idx) SIG_DESC_IP_BIT(ASPEED_IP_SCU, reg, idx, 1)
>
> #define SIG_DESC_LIST_SYM(sig, func) sig_descs_ ## sig ## _ ## func
> #define SIG_DESC_LIST_DECL(sig, func, ...) \
> @@ -500,7 +514,7 @@ struct aspeed_pin_desc {
> MS_PIN_DECL_(pin, SIG_EXPR_LIST_PTR(gpio))
>
> struct aspeed_pinctrl_data {
> - struct regmap *map;
> + struct regmap *maps[ASPEED_NR_PINMUX_IPS];
>
> const struct pinctrl_pin_desc *pins;
> const unsigned int npins;
> --
> 2.7.4
>
More information about the linux-arm-kernel
mailing list