[PATCH v3 4/5] arm64: dts: exynos: Add dts file for Exynos5433-based TM2 board

Andi Shyti andi.shyti at samsung.com
Thu Nov 3 05:26:22 PDT 2016


Hi Chanwoo,

Tested-by: Andi Shyti <andi.shyti at samsung.com>

Andi

On Thu, Nov 03, 2016 at 03:39:08PM +0900, Chanwoo Choi wrote:
> This patch adds the Device Tree source for Exynos5433-based Samsung TM2 board.
> This board fully support the all things for mobile target.
> 
> This patch supports the following devices:
> 1. basic SoC
> - Initial booting for Samsung Exynos5433 SoC
> - DRAM LPDDR3 (3GB)
> - eMMC (32GB)
> - ARM architecture timer
> 
> 2. power management devices
> - Sasmung S2MPS13 PMIC for the power supply
> - CPUFREQ for big.LITTLE cores
> - TMU for big.LITTLE cores and GPU
> - ADC with thermistor to measure the temperature of AP/Battery/Charger
> - Maxim MAX77843 Interface PMIC (MUIC/Haptic/Regulator)
> 
> 3. sound devices
> - I2S for sound bus
> - LPASS for sound power control
> - Wolfson WM5110 for sound codec
> - Maxim MAX98504 for speaker amplifier
> - TM2 ASoC Machine device driver node
> 
> 3. display devices
> - DECON, DSI and MIC for the panel output
> 
> 4. usb devices
> - USB 3.0 DRD (Dual Role Device)
> - USB 3.0 Host controller
> 
> 5. storage devices
> - MSHC (Mobile Storage Host Controller) for eMMC device
> 
> 6. misc devices
> - gpio-keys (power, volume up/down, home key)
> - PWM (Pulse Width Modulation Timer)
> 
> Signed-off-by: Chanwoo Choi <cw00.choi at samsung.com>
> Signed-off-by: Jaehoon Chung <jh80.chung at samsung.com>
> Signed-off-by: Seung-Woo Kim <sw0312.kim at samsung.com>
> Signed-off-by: Joonyoung Shim <jy0922.shim at samsung.com>
> Signed-off-by: Inki Dae <inki.dae at samsung.com>
> Signed-off-by: Jonghwa Lee <jonghwa3.lee at samsung.com>
> Signed-off-by: Beomho Seo <beomho.seo at samsung.com>
> Signed-off-by: Jaewon Kim <jaewon02.kim at samsung.com>
> Signed-off-by: Hyungwon Hwang <human.hwang at samsung.com>
> Signed-off-by: Inha Song <ideal.song at samsung.com>
> Signed-off-by: Ingi kim <ingi2.kim at samsung.com>
> Signed-off-by: Krzysztof Kozlowski <krzk at kernel.org>
> Signed-off-by: Marek Szyprowski <m.szyprowski at samsung.com>
> Signed-off-by: Andrzej Hajda <a.hajda at samsung.com>
> Signed-off-by: Sylwester Nawrocki <s.nawrocki at samsung.com>
> Reviewed-by: Krzysztof Kozlowski <krzk at kernel.org>
> Reviewed-by: Javier Martinez Canillas <javier at osg.samsung.com>
> ---
>  .../bindings/arm/samsung/samsung-boards.txt        |   1 +
>  arch/arm64/boot/dts/exynos/Makefile                |   4 +-
>  arch/arm64/boot/dts/exynos/exynos5433-tm2.dts      | 974 +++++++++++++++++++++
>  3 files changed, 978 insertions(+), 1 deletion(-)
>  create mode 100644 arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
> 
> diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt
> index 0ea7f14ef294..339af8b9cdc5 100644
> --- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt
> +++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt
> @@ -15,6 +15,7 @@ Required root node properties:
>  	- "samsung,xyref5260"	- for Exynos5260-based Samsung board.
>  	- "samsung,smdk5410"	- for Exynos5410-based Samsung SMDK5410 eval board.
>  	- "samsung,smdk5420"	- for Exynos5420-based Samsung SMDK5420 eval board.
> +	- "samsung,tm2"		- for Exynos5433-based Samsung TM2 board.
>  	- "samsung,sd5v1"	- for Exynos5440-based Samsung board.
>  	- "samsung,ssdk5440"	- for Exynos5440-based Samsung board.
>  
> diff --git a/arch/arm64/boot/dts/exynos/Makefile b/arch/arm64/boot/dts/exynos/Makefile
> index 50c9b9383cfa..947c750acba1 100644
> --- a/arch/arm64/boot/dts/exynos/Makefile
> +++ b/arch/arm64/boot/dts/exynos/Makefile
> @@ -1,4 +1,6 @@
> -dtb-$(CONFIG_ARCH_EXYNOS) += exynos7-espresso.dtb
> +dtb-$(CONFIG_ARCH_EXYNOS) += \
> +	exynos5433-tm2.dtb	\
> +	exynos7-espresso.dtb
>  
>  always		:= $(dtb-y)
>  subdir-y	:= $(dts-dirs)
> diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
> new file mode 100644
> index 000000000000..9ea3f32bae9e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
> @@ -0,0 +1,974 @@
> +/*
> + * SAMSUNG Exynos5433 TM2 board device tree source
> + *
> + * Copyright (c) 2016 Samsung Electronics Co., Ltd.
> + *
> + * Device tree source file for Samsung's TM2 board which is based on
> + * Samsung Exynos5433 SoC.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +/dts-v1/;
> +#include "exynos5433.dtsi"
> +#include <dt-bindings/clock/samsung,s2mps11.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +
> +/ {
> +	model = "Samsung TM2 board";
> +	compatible = "samsung,tm2", "samsung,exynos5433";
> +
> +	aliases {
> +		pinctrl0 = &pinctrl_alive;
> +		pinctrl1 = &pinctrl_aud;
> +		pinctrl2 = &pinctrl_cpif;
> +		pinctrl3 = &pinctrl_ese;
> +		pinctrl4 = &pinctrl_finger;
> +		pinctrl5 = &pinctrl_fsys;
> +		pinctrl6 = &pinctrl_imem;
> +		pinctrl7 = &pinctrl_nfc;
> +		pinctrl8 = &pinctrl_peric;
> +		pinctrl9 = &pinctrl_touch;
> +		serial0 = &serial_0;
> +		serial1 = &serial_1;
> +		serial2 = &serial_2;
> +		serial3 = &serial_3;
> +		spi0 = &spi_0;
> +		spi1 = &spi_1;
> +		spi2 = &spi_2;
> +		spi3 = &spi_3;
> +		spi4 = &spi_4;
> +	};
> +
> +	chosen {
> +		stdout-path = &serial_1;
> +	};
> +
> +	memory at 20000000 {
> +		device_type = "memory";
> +		reg = <0x0 0x20000000 0x0 0xc0000000>;
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +
> +		power-key {
> +			gpios = <&gpa2 7 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_POWER>;
> +			label = "power key";
> +			debounce-interval = <10>;
> +		};
> +
> +		volume-up-key {
> +			gpios = <&gpa2 0 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_VOLUMEUP>;
> +			label = "volume-up key";
> +			debounce-interval = <10>;
> +		};
> +
> +		volume-down-key {
> +			gpios = <&gpa2 1 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_VOLUMEDOWN>;
> +			label = "volume-down key";
> +			debounce-interval = <10>;
> +		};
> +
> +		homepage-key {
> +			gpios = <&gpa0 3 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_MENU>;
> +			label = "homepage key";
> +			debounce-interval = <10>;
> +		};
> +	};
> +
> +	i2c_max98504: i2c-gpio-0 {
> +		compatible = "i2c-gpio";
> +		gpios = <&gpd0 1 GPIO_ACTIVE_HIGH /* SPK_AMP_SDA */
> +			 &gpd0 0 GPIO_ACTIVE_HIGH /* SPK_AMP_SCL */ >;
> +		i2c-gpio,delay-us = <2>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		status = "okay";
> +
> +		max98504: max98504 at 31 {
> +			compatible = "maxim,max98504";
> +			reg = <0x31>;
> +			maxim,rx-path = <1>;
> +			maxim,tx-path = <1>;
> +			maxim,tx-channel-mask = <3>;
> +			maxim,tx-channel-source = <2>;
> +		};
> +	};
> +
> +	sound {
> +		compatible = "samsung,tm2-audio";
> +		audio-codec = <&wm5110>;
> +		i2s-controller = <&i2s0>;
> +		audio-amplifier = <&max98504>;
> +		mic-bias-gpios = <&gpr3 2 GPIO_ACTIVE_HIGH>;
> +		model = "wm5110";
> +		samsung,audio-routing =
> +			/* Headphone */
> +			"HP", "HPOUT1L",
> +			"HP", "HPOUT1R",
> +
> +			/* Speaker */
> +			"SPK", "SPKOUT",
> +			"SPKOUT", "HPOUT2L",
> +			"SPKOUT", "HPOUT2R",
> +
> +			/* Receiver */
> +			"RCV", "HPOUT3L",
> +			"RCV", "HPOUT3R";
> +		status = "okay";
> +	};
> +};
> +
> +&adc {
> +	vdd-supply = <&ldo3_reg>;
> +	status = "okay";
> +
> +	thermistor-ap {
> +		compatible = "murata,ncp03wf104";
> +		pullup-uv = <1800000>;
> +		pullup-ohm = <100000>;
> +		pulldown-ohm = <0>;
> +		io-channels = <&adc 0>;
> +	};
> +
> +	thermistor-battery {
> +		compatible = "murata,ncp03wf104";
> +		pullup-uv = <1800000>;
> +		pullup-ohm = <100000>;
> +		pulldown-ohm = <0>;
> +		io-channels = <&adc 1>;
> +		#thermal-sensor-cells = <0>;
> +	};
> +
> +	thermistor-charger {
> +		compatible = "murata,ncp03wf104";
> +		pullup-uv = <1800000>;
> +		pullup-ohm = <100000>;
> +		pulldown-ohm = <0>;
> +		io-channels = <&adc 2>;
> +	};
> +};
> +
> +&cpu0 {
> +	cpu-supply = <&buck3_reg>;
> +};
> +
> +&cpu4 {
> +	cpu-supply = <&buck2_reg>;
> +};
> +
> +&decon {
> +	status = "okay";
> +
> +	i80-if-timings {
> +	};
> +};
> +
> +&dsi {
> +	status = "okay";
> +	vddcore-supply = <&ldo6_reg>;
> +	vddio-supply = <&ldo7_reg>;
> +	samsung,pll-clock-frequency = <24000000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&te_irq>;
> +
> +	ports {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		port at 1 {
> +			reg = <1>;
> +
> +			dsi_out: endpoint {
> +				samsung,burst-clock-frequency = <512000000>;
> +				samsung,esc-clock-frequency = <16000000>;
> +			};
> +		};
> +	};
> +};
> +
> +&hsi2c_0 {
> +	status = "okay";
> +	clock-frequency = <2500000>;
> +
> +	s2mps13-pmic at 66 {
> +		compatible = "samsung,s2mps13-pmic";
> +		interrupt-parent = <&gpa0>;
> +		interrupts = <7 IRQ_TYPE_NONE>;
> +		reg = <0x66>;
> +		samsung,s2mps11-wrstbi-ground;
> +
> +		s2mps13_osc: clocks {
> +			compatible = "samsung,s2mps13-clk";
> +			#clock-cells = <1>;
> +			clock-output-names = "s2mps13_ap", "s2mps13_cp",
> +				"s2mps13_bt";
> +		};
> +
> +		regulators {
> +			ldo1_reg: LDO1 {
> +				regulator-name = "VDD_ALIVE_0.9V_AP";
> +				regulator-min-microvolt = <900000>;
> +				regulator-max-microvolt = <900000>;
> +				regulator-always-on;
> +			};
> +
> +			ldo2_reg: LDO2 {
> +				regulator-name = "VDDQ_MMC2_2.8V_AP";
> +				regulator-min-microvolt = <2800000>;
> +				regulator-max-microvolt = <2800000>;
> +				regulator-always-on;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			ldo3_reg: LDO3 {
> +				regulator-name = "VDD1_E_1.8V_AP";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-always-on;
> +			};
> +
> +			ldo4_reg: LDO4 {
> +				regulator-name = "VDD10_MIF_PLL_1.0V_AP";
> +				regulator-min-microvolt = <1300000>;
> +				regulator-max-microvolt = <1300000>;
> +				regulator-always-on;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			ldo5_reg: LDO5 {
> +				regulator-name = "VDD10_DPLL_1.0V_AP";
> +				regulator-min-microvolt = <1000000>;
> +				regulator-max-microvolt = <1000000>;
> +				regulator-always-on;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			ldo6_reg: LDO6 {
> +				regulator-name = "VDD10_MIPI2L_1.0V_AP";
> +				regulator-min-microvolt = <1000000>;
> +				regulator-max-microvolt = <1000000>;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			ldo7_reg: LDO7 {
> +				regulator-name = "VDD18_MIPI2L_1.8V_AP";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +			};
> +
> +			ldo8_reg: LDO8 {
> +				regulator-name = "VDD18_LLI_1.8V_AP";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-always-on;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			ldo9_reg: LDO9 {
> +				regulator-name = "VDD18_ABB_ETC_1.8V_AP";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-always-on;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			ldo10_reg: LDO10 {
> +				regulator-name = "VDD33_USB30_3.0V_AP";
> +				regulator-min-microvolt = <3000000>;
> +				regulator-max-microvolt = <3000000>;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			ldo11_reg: LDO11 {
> +				regulator-name = "VDD_INT_M_1.0V_AP";
> +				regulator-min-microvolt = <1000000>;
> +				regulator-max-microvolt = <1000000>;
> +				regulator-always-on;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			ldo12_reg: LDO12 {
> +				regulator-name = "VDD_KFC_M_1.1V_AP";
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <1350000>;
> +				regulator-always-on;
> +			};
> +
> +			ldo13_reg: LDO13 {
> +				regulator-name = "VDD_G3D_M_0.95V_AP";
> +				regulator-min-microvolt = <950000>;
> +				regulator-max-microvolt = <950000>;
> +				regulator-always-on;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			ldo14_reg: LDO14 {
> +				regulator-name = "VDDQ_M1_LDO_1.2V_AP";
> +				regulator-min-microvolt = <1200000>;
> +				regulator-max-microvolt = <1200000>;
> +				regulator-always-on;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			ldo15_reg: LDO15 {
> +				regulator-name = "VDDQ_M2_LDO_1.2V_AP";
> +				regulator-min-microvolt = <1200000>;
> +				regulator-max-microvolt = <1200000>;
> +				regulator-always-on;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			ldo16_reg: LDO16 {
> +				regulator-name = "VDDQ_EFUSE";
> +				regulator-min-microvolt = <1400000>;
> +				regulator-max-microvolt = <3400000>;
> +				regulator-always-on;
> +			};
> +
> +			ldo17_reg: LDO17 {
> +				regulator-name = "V_TFLASH_2.8V_AP";
> +				regulator-min-microvolt = <2800000>;
> +				regulator-max-microvolt = <2800000>;
> +			};
> +
> +			ldo18_reg: LDO18 {
> +				regulator-name = "V_CODEC_1.8V_AP";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +			};
> +
> +			ldo19_reg: LDO19 {
> +				regulator-name = "VDDA_1.8V_COMP";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-always-on;
> +			};
> +
> +			ldo20_reg: LDO20 {
> +				regulator-name = "VCC_2.8V_AP";
> +				regulator-min-microvolt = <2800000>;
> +				regulator-max-microvolt = <2800000>;
> +				regulator-always-on;
> +			};
> +
> +			ldo21_reg: LDO21 {
> +				regulator-name = "VT_CAM_1.8V";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +			};
> +
> +			ldo22_reg: LDO22 {
> +				regulator-name = "CAM_IO_1.8V_AP";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +			};
> +
> +			ldo23_reg: LDO23 {
> +				regulator-name = "CAM_SEN_CORE_1.2V_AP";
> +				regulator-min-microvolt = <1050000>;
> +				regulator-max-microvolt = <1200000>;
> +			};
> +
> +			ldo24_reg: LDO24 {
> +				regulator-name = "VT_CAM_1.2V";
> +				regulator-min-microvolt = <1200000>;
> +				regulator-max-microvolt = <1200000>;
> +			};
> +
> +			ldo25_reg: LDO25 {
> +				regulator-name = "CAM_SEN_A2.8V_AP";
> +				regulator-min-microvolt = <2800000>;
> +				regulator-max-microvolt = <2800000>;
> +			};
> +
> +			ldo26_reg: LDO26 {
> +				regulator-name = "CAM_AF_2.8V_AP";
> +				regulator-min-microvolt = <2800000>;
> +				regulator-max-microvolt = <2800000>;
> +			};
> +
> +			ldo27_reg: LDO27 {
> +				regulator-name = "VCC_3.0V_LCD_AP";
> +				regulator-min-microvolt = <3000000>;
> +				regulator-max-microvolt = <3000000>;
> +			};
> +
> +			ldo28_reg: LDO28 {
> +				regulator-name = "VCC_1.8V_LCD_AP";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +			};
> +
> +			ldo29_reg: LDO29 {
> +				regulator-name = "VT_CAM_2.8V";
> +				regulator-min-microvolt = <3000000>;
> +				regulator-max-microvolt = <3000000>;
> +			};
> +
> +			ldo30_reg: LDO30 {
> +				regulator-name = "TSP_AVDD_3.3V_AP";
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +			};
> +
> +			ldo31_reg: LDO31 {
> +				regulator-name = "TSP_VDD_1.85V_AP";
> +				regulator-min-microvolt = <1850000>;
> +				regulator-max-microvolt = <1850000>;
> +			};
> +
> +			ldo32_reg: LDO32 {
> +				regulator-name = "VTOUCH_1.8V_AP";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +			};
> +
> +			ldo33_reg: LDO33 {
> +				regulator-name = "VTOUCH_LED_3.3V";
> +				regulator-min-microvolt = <2500000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-ramp-delay = <12500>;
> +			};
> +
> +			ldo34_reg: LDO34 {
> +				regulator-name = "VCC_1.8V_MHL_AP";
> +				regulator-min-microvolt = <1000000>;
> +				regulator-max-microvolt = <2100000>;
> +			};
> +
> +			ldo35_reg: LDO35 {
> +				regulator-name = "OIS_VM_2.8V";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <2800000>;
> +			};
> +
> +			ldo36_reg: LDO36 {
> +				regulator-name = "VSIL_1.0V";
> +				regulator-min-microvolt = <1000000>;
> +				regulator-max-microvolt = <1000000>;
> +			};
> +
> +			ldo37_reg: LDO37 {
> +				regulator-name = "VF_1.8V";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +			};
> +
> +			ldo38_reg: LDO38 {
> +				regulator-name = "VCC_3.0V_MOTOR_AP";
> +				regulator-min-microvolt = <3000000>;
> +				regulator-max-microvolt = <3000000>;
> +			};
> +
> +			ldo39_reg: LDO39 {
> +				regulator-name = "V_HRM_1.8V";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +			};
> +
> +			ldo40_reg: LDO40 {
> +				regulator-name = "V_HRM_3.3V";
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +			};
> +
> +			buck1_reg: BUCK1 {
> +				regulator-name = "VDD_MIF_0.9V_AP";
> +				regulator-min-microvolt = <600000>;
> +				regulator-max-microvolt = <1500000>;
> +				regulator-always-on;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			buck2_reg: BUCK2 {
> +				regulator-name = "VDD_EGL_1.0V_AP";
> +				regulator-min-microvolt = <900000>;
> +				regulator-max-microvolt = <1300000>;
> +				regulator-always-on;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			buck3_reg: BUCK3 {
> +				regulator-name = "VDD_KFC_1.0V_AP";
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <1200000>;
> +				regulator-always-on;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			buck4_reg: BUCK4 {
> +				regulator-name = "VDD_INT_0.95V_AP";
> +				regulator-min-microvolt = <600000>;
> +				regulator-max-microvolt = <1500000>;
> +				regulator-always-on;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			buck5_reg: BUCK5 {
> +				regulator-name = "VDD_DISP_CAM0_0.9V_AP";
> +				regulator-min-microvolt = <600000>;
> +				regulator-max-microvolt = <1500000>;
> +				regulator-always-on;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			buck6_reg: BUCK6 {
> +				regulator-name = "VDD_G3D_0.9V_AP";
> +				regulator-min-microvolt = <600000>;
> +				regulator-max-microvolt = <1500000>;
> +				regulator-always-on;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			buck7_reg: BUCK7 {
> +				regulator-name = "VDD_MEM1_1.2V_AP";
> +				regulator-min-microvolt = <1200000>;
> +				regulator-max-microvolt = <1200000>;
> +				regulator-always-on;
> +			};
> +
> +			buck8_reg: BUCK8 {
> +				regulator-name = "VDD_LLDO_1.35V_AP";
> +				regulator-min-microvolt = <1350000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-always-on;
> +			};
> +
> +			buck9_reg: BUCK9 {
> +				regulator-name = "VDD_MLDO_2.0V_AP";
> +				regulator-min-microvolt = <1350000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-always-on;
> +			};
> +
> +			buck10_reg: BUCK10 {
> +				regulator-name = "vdd_mem2";
> +				regulator-min-microvolt = <550000>;
> +				regulator-max-microvolt = <1500000>;
> +				regulator-always-on;
> +			};
> +		};
> +	};
> +};
> +
> +&hsi2c_8 {
> +	status = "okay";
> +
> +	max77843 at 66 {
> +		compatible = "maxim,max77843";
> +		interrupt-parent = <&gpa1>;
> +		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
> +		reg = <0x66>;
> +
> +		muic: max77843-muic {
> +			compatible = "maxim,max77843-muic";
> +		};
> +
> +		regulators {
> +			compatible = "maxim,max77843-regulator";
> +			safeout1_reg: SAFEOUT1 {
> +				regulator-name = "SAFEOUT1";
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <4950000>;
> +			};
> +
> +			safeout2_reg: SAFEOUT2 {
> +				regulator-name = "SAFEOUT2";
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <4950000>;
> +			};
> +
> +			charger_reg: CHARGER {
> +				regulator-name = "CHARGER";
> +				regulator-min-microamp = <100000>;
> +				regulator-max-microamp = <3150000>;
> +			};
> +		};
> +
> +		haptic: max77843-haptic {
> +			compatible = "maxim,max77843-haptic";
> +			haptic-supply = <&ldo38_reg>;
> +			pwms = <&pwm 0 33670 0>;
> +			pwm-names = "haptic";
> +		};
> +	};
> +};
> +
> +&i2s0 {
> +	status = "okay";
> +};
> +
> +&mshc_0 {
> +	status = "okay";
> +	num-slots = <1>;
> +	non-removable;
> +	card-detect-delay = <200>;
> +	samsung,dw-mshc-ciu-div = <3>;
> +	samsung,dw-mshc-sdr-timing = <0 4>;
> +	samsung,dw-mshc-ddr-timing = <0 2>;
> +	samsung,dw-mshc-hs400-timing = <0 3>;
> +	samsung,read-strobe-delay = <90>;
> +	fifo-depth = <0x80>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_qrdy &sd0_bus1 &sd0_bus4
> +			&sd0_bus8 &sd0_rdqs>;
> +	bus-width = <8>;
> +	assigned-clocks = <&cmu_top CLK_SCLK_MMC0_FSYS>;
> +	assigned-clock-rates = <800000000>;
> +};
> +
> +&pinctrl_alive {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&initial_alive>;
> +
> +	initial_alive: initial-state {
> +		PIN(IN, gpa0-0, DOWN, LV1);
> +		PIN(IN, gpa0-1, NONE, LV1);
> +		PIN(IN, gpa0-2, DOWN, LV1);
> +		PIN(IN, gpa0-3, NONE, LV1);
> +		PIN(IN, gpa0-4, NONE, LV1);
> +		PIN(IN, gpa0-5, DOWN, LV1);
> +		PIN(IN, gpa0-6, NONE, LV1);
> +		PIN(IN, gpa0-7, NONE, LV1);
> +
> +		PIN(IN, gpa1-0, UP, LV1);
> +		PIN(IN, gpa1-1, NONE, LV1);
> +		PIN(IN, gpa1-2, NONE, LV1);
> +		PIN(IN, gpa1-3, DOWN, LV1);
> +		PIN(IN, gpa1-4, DOWN, LV1);
> +		PIN(IN, gpa1-5, NONE, LV1);
> +		PIN(IN, gpa1-6, NONE, LV1);
> +		PIN(IN, gpa1-7, NONE, LV1);
> +
> +		PIN(IN, gpa2-0, NONE, LV1);
> +		PIN(IN, gpa2-1, NONE, LV1);
> +		PIN(IN, gpa2-2, NONE, LV1);
> +		PIN(IN, gpa2-3, DOWN, LV1);
> +		PIN(IN, gpa2-4, NONE, LV1);
> +		PIN(IN, gpa2-5, DOWN, LV1);
> +		PIN(IN, gpa2-6, DOWN, LV1);
> +		PIN(IN, gpa2-7, NONE, LV1);
> +
> +		PIN(IN, gpa3-0, DOWN, LV1);
> +		PIN(IN, gpa3-1, DOWN, LV1);
> +		PIN(IN, gpa3-2, NONE, LV1);
> +		PIN(IN, gpa3-3, DOWN, LV1);
> +		PIN(IN, gpa3-4, NONE, LV1);
> +		PIN(IN, gpa3-5, DOWN, LV1);
> +		PIN(IN, gpa3-6, DOWN, LV1);
> +		PIN(IN, gpa3-7, DOWN, LV1);
> +
> +		PIN(IN, gpf1-0, NONE, LV1);
> +		PIN(IN, gpf1-1, NONE, LV1);
> +		PIN(IN, gpf1-2, DOWN, LV1);
> +		PIN(IN, gpf1-4, UP, LV1);
> +		PIN(OUT, gpf1-5, NONE, LV1);
> +		PIN(IN, gpf1-6, DOWN, LV1);
> +		PIN(IN, gpf1-7, DOWN, LV1);
> +
> +		PIN(IN, gpf2-0, DOWN, LV1);
> +		PIN(IN, gpf2-1, DOWN, LV1);
> +		PIN(IN, gpf2-2, DOWN, LV1);
> +		PIN(IN, gpf2-3, DOWN, LV1);
> +
> +		PIN(IN, gpf3-0, DOWN, LV1);
> +		PIN(IN, gpf3-1, DOWN, LV1);
> +		PIN(IN, gpf3-2, NONE, LV1);
> +		PIN(IN, gpf3-3, DOWN, LV1);
> +
> +		PIN(IN, gpf4-0, DOWN, LV1);
> +		PIN(IN, gpf4-1, DOWN, LV1);
> +		PIN(IN, gpf4-2, DOWN, LV1);
> +		PIN(IN, gpf4-3, DOWN, LV1);
> +		PIN(IN, gpf4-4, DOWN, LV1);
> +		PIN(IN, gpf4-5, DOWN, LV1);
> +		PIN(IN, gpf4-6, DOWN, LV1);
> +		PIN(IN, gpf4-7, DOWN, LV1);
> +
> +		PIN(IN, gpf5-0, DOWN, LV1);
> +		PIN(IN, gpf5-1, DOWN, LV1);
> +		PIN(IN, gpf5-2, DOWN, LV1);
> +		PIN(IN, gpf5-3, DOWN, LV1);
> +		PIN(OUT, gpf5-4, NONE, LV1);
> +		PIN(IN, gpf5-5, DOWN, LV1);
> +		PIN(IN, gpf5-6, DOWN, LV1);
> +		PIN(IN, gpf5-7, DOWN, LV1);
> +	};
> +
> +	te_irq: te_irq {
> +		samsung,pins = "gpf1-3";
> +		samsung,pin-function = <0xf>;
> +	};
> +};
> +
> +&pinctrl_cpif {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&initial_cpif>;
> +
> +	initial_cpif: initial-state {
> +		PIN(IN, gpv6-0, DOWN, LV1);
> +		PIN(IN, gpv6-1, DOWN, LV1);
> +	};
> +};
> +
> +&pinctrl_ese {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&initial_ese>;
> +
> +	initial_ese: initial-state {
> +		PIN(IN, gpj2-0, DOWN, LV1);
> +		PIN(IN, gpj2-1, DOWN, LV1);
> +		PIN(IN, gpj2-2, DOWN, LV1);
> +	};
> +};
> +
> +&pinctrl_fsys {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&initial_fsys>;
> +
> +	initial_fsys: initial-state {
> +		PIN(IN, gpr3-0, NONE, LV1);
> +		PIN(IN, gpr3-1, DOWN, LV1);
> +		PIN(IN, gpr3-2, DOWN, LV1);
> +		PIN(IN, gpr3-3, DOWN, LV1);
> +		PIN(IN, gpr3-7, NONE, LV1);
> +	};
> +};
> +
> +&pinctrl_imem {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&initial_imem>;
> +
> +	initial_imem: initial-state {
> +		PIN(IN, gpf0-0, UP, LV1);
> +		PIN(IN, gpf0-1, UP, LV1);
> +		PIN(IN, gpf0-2, DOWN, LV1);
> +		PIN(IN, gpf0-3, UP, LV1);
> +		PIN(IN, gpf0-4, DOWN, LV1);
> +		PIN(IN, gpf0-5, NONE, LV1);
> +		PIN(IN, gpf0-6, DOWN, LV1);
> +		PIN(IN, gpf0-7, UP, LV1);
> +	};
> +};
> +
> +&pinctrl_nfc {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&initial_nfc>;
> +
> +	initial_nfc: initial-state {
> +		PIN(IN, gpj0-2, DOWN, LV1);
> +	};
> +};
> +
> +&pinctrl_peric {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&initial_peric>;
> +
> +	initial_peric: initial-state {
> +		PIN(IN, gpv7-0, DOWN, LV1);
> +		PIN(IN, gpv7-1, DOWN, LV1);
> +		PIN(IN, gpv7-2, NONE, LV1);
> +		PIN(IN, gpv7-3, DOWN, LV1);
> +		PIN(IN, gpv7-4, DOWN, LV1);
> +		PIN(IN, gpv7-5, DOWN, LV1);
> +
> +		PIN(IN, gpb0-4, DOWN, LV1);
> +
> +		PIN(IN, gpc0-2, DOWN, LV1);
> +		PIN(IN, gpc0-5, DOWN, LV1);
> +		PIN(IN, gpc0-7, DOWN, LV1);
> +
> +		PIN(IN, gpc1-1, DOWN, LV1);
> +
> +		PIN(IN, gpc3-4, NONE, LV1);
> +		PIN(IN, gpc3-5, NONE, LV1);
> +		PIN(IN, gpc3-6, NONE, LV1);
> +		PIN(IN, gpc3-7, NONE, LV1);
> +
> +		PIN(OUT, gpg0-0, NONE, LV1);
> +		PIN(FUNC1, gpg0-1, DOWN, LV1);
> +
> +		PIN(IN, gpd2-5, DOWN, LV1);
> +
> +		PIN(IN, gpd4-0, NONE, LV1);
> +		PIN(IN, gpd4-1, DOWN, LV1);
> +		PIN(IN, gpd4-2, DOWN, LV1);
> +		PIN(IN, gpd4-3, DOWN, LV1);
> +		PIN(IN, gpd4-4, DOWN, LV1);
> +
> +		PIN(IN, gpd6-3, DOWN, LV1);
> +
> +		PIN(IN, gpd8-1, UP, LV1);
> +
> +		PIN(IN, gpg1-0, DOWN, LV1);
> +		PIN(IN, gpg1-1, DOWN, LV1);
> +		PIN(IN, gpg1-2, DOWN, LV1);
> +		PIN(IN, gpg1-3, DOWN, LV1);
> +		PIN(IN, gpg1-4, DOWN, LV1);
> +
> +		PIN(IN, gpg2-0, DOWN, LV1);
> +		PIN(IN, gpg2-1, DOWN, LV1);
> +
> +		PIN(IN, gpg3-0, DOWN, LV1);
> +		PIN(IN, gpg3-1, DOWN, LV1);
> +		PIN(IN, gpg3-5, DOWN, LV1);
> +		PIN(IN, gpg3-7, DOWN, LV1);
> +	};
> +};
> +
> +&pinctrl_touch {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&initial_touch>;
> +
> +	initial_touch: initial-state {
> +		PIN(IN, gpj1-2, DOWN, LV1);
> +	};
> +};
> +
> +&pwm {
> +	pinctrl-0 = <&pwm0_out>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +};
> +
> +&mic {
> +	status = "okay";
> +
> +	i80-if-timings {
> +	};
> +};
> +
> +&serial_1 {
> +	status = "okay";
> +};
> +
> +&serial_3 {
> +	assigned-clocks = <&cmu_aud CLK_MOUT_AUD_PLL_USER>;
> +	assigned-clock-parents = <&cmu_top CLK_FOUT_AUD_PLL>;
> +	status = "okay";
> +};
> +
> +&spi_1 {
> +	cs-gpios = <&gpd6 3 GPIO_ACTIVE_HIGH>;
> +	status = "okay";
> +
> +	wm5110: wm5110-codec at 0 {
> +		compatible = "wlf,wm5110";
> +		reg = <0x0>;
> +		spi-max-frequency = <20000000>;
> +		interrupt-parent = <&gpa0>;
> +		interrupts = <4 IRQ_TYPE_NONE>;
> +		clocks = <&pmu_system_controller 0>,
> +			<&s2mps13_osc S2MPS11_CLK_BT>;
> +		clock-names = "mclk1", "mclk2";
> +
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		wlf,micd-detect-debounce = <300>;
> +		wlf,micd-bias-start-time = <0x1>;
> +		wlf,micd-rate = <0x7>;
> +		wlf,micd-dbtime = <0x1>;
> +		wlf,micd-force-micbias;
> +		wlf,micd-configs = <0x0 1 0>;
> +		wlf,hpdet-channel = <1>;
> +		wlf,gpsw = <0x1>;
> +		wlf,inmode = <2 0 2 0>;
> +
> +		wlf,reset = <&gpc0 7 GPIO_ACTIVE_HIGH>;
> +		wlf,ldoena = <&gpf0 0 GPIO_ACTIVE_HIGH>;
> +
> +		/* core supplies */
> +		AVDD-supply = <&ldo18_reg>;
> +		DBVDD1-supply = <&ldo18_reg>;
> +		CPVDD-supply = <&ldo18_reg>;
> +		DBVDD2-supply = <&ldo18_reg>;
> +		DBVDD3-supply = <&ldo18_reg>;
> +
> +		controller-data {
> +			samsung,spi-feedback-delay = <0>;
> +		};
> +	};
> +};
> +
> +&timer {
> +	clock-frequency = <24000000>;
> +};
> +
> +&tmu_atlas0 {
> +	vtmu-supply = <&ldo3_reg>;
> +	status = "okay";
> +};
> +
> +&tmu_apollo {
> +	vtmu-supply = <&ldo3_reg>;
> +	status = "okay";
> +};
> +
> +&tmu_g3d {
> +	vtmu-supply = <&ldo3_reg>;
> +	status = "okay";
> +};
> +
> +&usbdrd30 {
> +	vdd33-supply = <&ldo10_reg>;
> +	vdd10-supply = <&ldo6_reg>;
> +	status = "okay";
> +};
> +
> +&usbdrd_dwc3_0 {
> +	dr_mode = "otg";
> +};
> +
> +&usbdrd30_phy {
> +	vbus-supply = <&safeout1_reg>;
> +	status = "okay";
> +};
> +
> +&xxti {
> +	clock-frequency = <24000000>;
> +};
> -- 
> 1.9.1
> 



More information about the linux-arm-kernel mailing list