[PATCH 1/2] ARM: dts: imx6q: extend support for the cm-fx6

[christopher.spinrath at rwth-aachen.de]

From: Christopher Spinrath <christopher.spinrath at rwth-aachen.de>

The cm-fx6 module has an on-board spi-flash chip for its firmware, an
eeprom (containing e.g. the mac address of the on-board Ethernet),
a sata port, a pcie controller, an USB hub, and an USB otg port.
Enable support for them. In addition, enable syscon poweroff support.

Signed-off-by: Christopher Spinrath <christopher.spinrath at rwth-aachen.de>
---
 arch/arm/boot/dts/imx6q-cm-fx6.dts | 136 +++++++++++++++++++++++++++++++++++++
 1 file changed, 136 insertions(+)

diff --git a/arch/arm/boot/dts/imx6q-cm-fx6.dts b/arch/arm/boot/dts/imx6q-cm-fx6.dts
index 99b46f8..f4fc22e 100644
--- a/arch/arm/boot/dts/imx6q-cm-fx6.dts
+++ b/arch/arm/boot/dts/imx6q-cm-fx6.dts
@@ -31,6 +31,61 @@
 			linux,default-trigger = "heartbeat";
 		};
 	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reg_usb_otg_vbus: usb_otg_vbus {
+			compatible = "regulator-fixed";
+			regulator-name = "usb_otg_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio3 22 0>;
+			enable-active-high;
+		};
+
+		reg_usb_h1_vbus: usb_h1_vbus {
+			compatible = "regulator-fixed";
+			regulator-name = "usb_h1_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio7 8 0>;
+			enable-active-high;
+		};
+	};
+};
+
+&ecspi1 {
+	fsl,spi-num-chipselects = <2>;
+	cs-gpios = <&gpio2 30 0>, <&gpio3 19 0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash: m25p80 at 0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "st,m25p", "jedec,spi-nor";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+
+		partition at 0 {
+			label = "uboot";
+			reg = <0x0 0xc0000>;
+		};
+
+		partition at c0000 {
+			label = "uboot environment";
+			reg = <0xc0000 0x40000>;
+		};
+
+		partition at 100000 {
+			label = "reserved";
+			reg = <0x100000 0x100000>;
+		};
+	};
 };
 
 &fec {
@@ -46,8 +101,31 @@
 	status = "okay";
 };
 
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+	clock-frequency = <100000>;
+
+	eeprom at 50 {
+		compatible = "at24,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
 &iomuxc {
 	imx6q-cm-fx6 {
+		pinctrl_ecspi1: ecspi1grp {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		 0x100b1
+				MX6QDL_PAD_EIM_D17__ECSPI1_MISO		 0x100b1
+				MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		 0x100b1
+				MX6QDL_PAD_EIM_EB2__GPIO2_IO30		0x100b1
+				MX6QDL_PAD_EIM_D19__GPIO3_IO19		0x100b1
+			>;
+		};
+
 		pinctrl_enet: enetgrp {
 			fsl,pins = <
 				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
@@ -91,17 +169,75 @@
 			>;
 		};
 
+		pinctrl_i2c3: i2c3grp {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1
+				MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+			>;
+		};
+
+		pinctrl_pcie: pciegrp {
+			fsl,pins = <
+				MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x80000000
+				MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x80000000
+			>;
+		};
+
 		pinctrl_uart4: uart4grp {
 			fsl,pins = <
 				MX6QDL_PAD_KEY_COL0__UART4_TX_DATA	0x1b0b1
 				MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA	0x1b0b1
 			>;
 		};
+
+		pinctrl_usbh1: usbh1grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x80000000
+			>;
+		};
+
+		pinctrl_usbotg: usbotggrp {
+			fsl,pins = <
+				MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
+				MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x80000000
+			>;
+		};
 	};
 };
 
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio1 26 0>;
+	power-on-gpio = <&gpio2 24 0>;
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&snvs_poweroff {
+	status = "okay";
+};
+
 &uart4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart4>;
 	status = "okay";
 };
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb_h1_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbh1>;
+	status = "okay";
+};
-- 
2.8.2