[PATCH 2/5] i2c: Add STM32F4 I2C driver
M'boumba Cedric Madianga
cedric.madianga at gmail.com
Wed May 18 00:24:50 PDT 2016
Hi Maxime,
2016-05-17 11:48 GMT+02:00 Maxime Coquelin <mcoquelin.stm32 at gmail.com>:
> Hi Cedric,
>
> 2016-05-11 17:36 GMT+02:00 M'boumba Cedric Madianga <cedric.madianga at gmail.com>:
>> This patch adds support for the STM32F4 I2C controller.
>>
>> Signed-off-by: M'boumba Cedric Madianga <cedric.madianga at gmail.com>
>> ---
>> drivers/i2c/busses/Kconfig | 10 +
>> drivers/i2c/busses/Makefile | 1 +
>> drivers/i2c/busses/i2c-stm32f4.c | 872 +++++++++++++++++++++++++++++++++++++++
>> 3 files changed, 883 insertions(+)
>> create mode 100644 drivers/i2c/busses/i2c-stm32f4.c
>>
> ...
>> diff --git a/drivers/i2c/busses/i2c-stm32f4.c b/drivers/i2c/busses/i2c-stm32f4.c
>> new file mode 100644
>> index 0000000..4692213
>> --- /dev/null
>> +++ b/drivers/i2c/busses/i2c-stm32f4.c
> ...
>> +enum stm32f4_i2c_speed {
>> + STM32F4_I2C_SPEED_STANDARD, /* 100 kHz */
>> + STM32F4_I2C_SPEED_FAST, /* 400 kHz */
>> + STM32F4_I2C_SPEED_END,
>> +};
>> +
>> +/**
>> + * struct stm32f4_i2c_timings - per-Mode tuning parameters
>> + * @rate: I2C bus rate
>> + * @duty: Fast mode duty cycle
>> + */
>> +struct stm32f4_i2c_timings {
>> + u32 rate;
>> + u32 duty;
>> +};
> ...
>> +/**
>> + * struct stm32f4_i2c_dev - private data of the controller
>> + * @adap: I2C adapter for this controller
>> + * @dev: device for this controller
>> + * @base: virtual memory area
>> + * @complete: completion of I2C message
>> + * @irq_event: interrupt event line for the controller
>> + * @irq_error: interrupt error line for the controller
>> + * @clk: hw i2c clock
>> + * speed: I2C clock frequency of the controller. Standard or Fast only supported
>> + * @client: I2C transfer information
>> + * @busy: I2C transfer on-going
>> + * @rst: I2C reset line
>> + */
>> +struct stm32f4_i2c_dev {
>> + struct i2c_adapter adap;
>> + struct device *dev;
>> + void __iomem *base;
>> + struct completion complete;
>> + int irq_event;
>> + int irq_error;
>> + struct clk *clk;
>> + int speed;
>> + struct stm32f4_i2c_client client;
>> + bool busy;
>> + struct reset_control *rst;
>> +};
>> +
>> +static struct stm32f4_i2c_timings i2c_timings[] = {
>> + [STM32F4_I2C_SPEED_STANDARD] = {
>> + .rate = 100000,
>> + .duty = 0,
>> + },
>> + [STM32F4_I2C_SPEED_FAST] = {
>> + .rate = 400000,
>> + .duty = 0,
>> + },
>> +};
> Is this table really needed?
> As duty value seems to always be 0, couldn't you just store the rate
> in the speed field?
You are right. I will directly use speed field in the V2
>
>
>> +static void stm32f4_i2c_set_rise_time(struct stm32f4_i2c_dev *i2c_dev)
>> +{
>> + u32 trise, freq, cr2;
>> +
>> + cr2 = readl_relaxed(i2c_dev->base + STM32F4_I2C_CR2);
>> + freq = cr2 & STM32F4_I2C_CR2_FREQ_MASK;
>> +
>> + trise = readl_relaxed(i2c_dev->base + STM32F4_I2C_TRISE);
>> + trise &= ~STM32F4_I2C_TRISE_TRISE_MASK;
>> +
>> + if (i2c_dev->speed == STM32F4_I2C_SPEED_STANDARD)
>> + trise |= STM32F4_I2C_TRISE_TRISE((freq + 1));
>> + else
>> + trise |= STM32F4_I2C_TRISE_TRISE((((freq * 300) / 1000) + 1));
> Or if you keep the timings struct, maybe the rise time should be part of it.
> Doing, that, you will avoid the if/else
As timings struct will be removed, I will keep this piece of code but
thanks for this remark.
>
>> +
>> + writel_relaxed(trise, i2c_dev->base + STM32F4_I2C_TRISE);
>> +}
>> +
>> +static void stm32f4_i2c_set_speed_mode(struct stm32f4_i2c_dev *i2c_dev)
>> +{
>> + struct stm32f4_i2c_timings *t = &i2c_timings[i2c_dev->speed];
>> + u32 ccr, val, clk_rate;
>> +
>> + ccr = readl_relaxed(i2c_dev->base + STM32F4_I2C_CCR);
>> + ccr &= ~(STM32F4_I2C_CCR_FS | STM32F4_I2C_CCR_DUTY |
>> + STM32F4_I2C_CCR_CCR_MASK);
>> +
>> + clk_rate = clk_get_rate(i2c_dev->clk);
>> +
>> + switch (i2c_dev->speed) {
>> + case STM32F4_I2C_SPEED_STANDARD:
>> + val = clk_rate / t->rate * 2;
>> + if (val < STM32F4_I2C_MIN_CCR)
>> + ccr |= STM32F4_I2C_CCR_CCR(STM32F4_I2C_MIN_CCR);
>> + else
>> + ccr |= STM32F4_I2C_CCR_CCR(val);
>> + break;
>> + case STM32F4_I2C_SPEED_FAST:
>> + ccr |= STM32F4_I2C_CCR_FS;
>> + if (t->duty) {
>> + ccr |= STM32F4_I2C_CCR_DUTY;
>> + ccr |= STM32F4_I2C_CCR_CCR(clk_rate / t->rate * 25);
>> + } else {
>> + ccr |= STM32F4_I2C_CCR_CCR(clk_rate / t->rate * 3);
>> + }
> Is it really useful since duty seems to always be 0?
Agree, I will rework it by directly set duty at 0 in the register.
>
>> + break;
>> + default:
>> + dev_err(i2c_dev->dev, "I2C speed mode not supported\n");
>> + }
>> +
>> + writel_relaxed(ccr, i2c_dev->base + STM32F4_I2C_CCR);
>> +}
>> +
>> +static void stm32f4_i2c_set_filter(struct stm32f4_i2c_dev *i2c_dev)
>> +{
>> + u32 filter;
>> +
>> + /* Enable analog noise filter and disable digital noise filter */
> Maybe a stupid question, but is it always what we want?
> Are there some cases we would prefer to use the digital noise filter
> instead of the analog one?
I don't have any use case where the digital noise filter is used.
So as I cannot test it, I prefer to only use the default filter (analog)
>
>> + filter = readl_relaxed(i2c_dev->base + STM32F4_I2C_FLTR);
>> + filter &= ~(STM32F4_I2C_FLTR_ANOFF | STM32F4_I2C_FLTR_DNF_MASK);
>> + writel_relaxed(filter, i2c_dev->base + STM32F4_I2C_FLTR);
>> +}
>> +
>> +/**
>> + * stm32f4_i2c_hw_config() - Prepare I2C block
>> + * @i2c_dev: Controller's private data
>> + */
>> +static void stm32f4_i2c_hw_config(struct stm32f4_i2c_dev *i2c_dev)
>> +{
>> + void __iomem *reg = i2c_dev->base + STM32F4_I2C_CR1;
>> +
>> + /* Disable I2C */
>> + stm32f4_i2c_clr_bits(reg, STM32F4_I2C_CR1_PE);
>> +
>> + stm32f4_i2c_set_periph_clk_freq(i2c_dev);
>> +
>> + stm32f4_i2c_set_rise_time(i2c_dev);
>> +
>> + stm32f4_i2c_set_speed_mode(i2c_dev);
>> +
>> + stm32f4_i2c_set_filter(i2c_dev);
>> +
>> + /* Enable I2C */
>> + stm32f4_i2c_set_bits(reg, STM32F4_I2C_CR1_PE);
>> +}
>> +
>> +static int stm32f4_i2c_wait_free_bus(struct stm32f4_i2c_dev *i2c_dev)
>> +{
>> + u32 status;
>> + int ret;
>> +
>> + ret = readl_relaxed_poll_timeout(i2c_dev->base + STM32F4_I2C_SR2,
>> + status,
>> + !(status & STM32F4_I2C_SR2_BUSY),
>> + 10, 1000);
>> + if (ret) {
>> + dev_err(i2c_dev->dev, "bus not free\n");
>> + ret = -EBUSY;
>> + }
>> +
>> + return ret;
>> +}
>> +
>> +/**
>> + * stm32f4_i2c_write_ byte() - Write a byte in the data register
>> + * @i2c_dev: Controller's private data
>> + * @byte: Data to write in the register
>> + */
>> +static void stm32f4_i2c_write_byte(struct stm32f4_i2c_dev *i2c_dev, u8 byte)
>> +{
>> + writel_relaxed(byte, i2c_dev->base + STM32F4_I2C_DR);
>> +}
>> +
>> +/**
>> + * stm32f4_i2c_write_msg() - Fill the data register in write mode
>> + * @i2c_dev: Controller's private data
>> + *
>> + * This function fills the data register with I2C transfer buffer
>> + */
>> +static void stm32f4_i2c_write_msg(struct stm32f4_i2c_dev *i2c_dev)
>> +{
>> + struct stm32f4_i2c_client *c = &i2c_dev->client;
>> +
>> + stm32f4_i2c_write_byte(i2c_dev, *c->buf++);
>> + c->count--;
>> +}
>> +
>> +static void stm32f4_i2c_read_msg(struct stm32f4_i2c_dev *i2c_dev)
>> +{
>> + struct stm32f4_i2c_client *c = &i2c_dev->client;
>> + u32 rbuf;
>> +
>> + rbuf = readl_relaxed(i2c_dev->base + STM32F4_I2C_DR);
>> + *c->buf++ = (u8)rbuf & 0xff;
>> + c->count--;
>> +}
>> +
>> +static void stm32f4_i2c_terminate_xfer(struct stm32f4_i2c_dev *i2c_dev)
>> +{
>> + struct stm32f4_i2c_client *c = &i2c_dev->client;
>> + void __iomem *reg = i2c_dev->base + STM32F4_I2C_CR2;
>> +
>> + /* Disable all interrupts */
>> + stm32f4_i2c_clr_bits(reg, STM32F4_I2C_CR2_IRQ_MASK);
>> +
>> + /* Set STOP or REPSTART */
>> + reg = i2c_dev->base + STM32F4_I2C_CR1;
>> + if (c->stop)
>> + stm32f4_i2c_set_bits(reg, STM32F4_I2C_CR1_STOP);
>> + else
>> + stm32f4_i2c_set_bits(reg, STM32F4_I2C_CR1_START);
>> +
>> + complete(&i2c_dev->complete);
>> +}
>> +
>> +/**
>> + * stm32f4_i2c_handle_write() - Handle FIFO empty interrupt in case of write
>> + * @i2c_dev: Controller's private data
>> + */
>> +static void stm32f4_i2c_handle_write(struct stm32f4_i2c_dev *i2c_dev)
>> +{
>> + struct stm32f4_i2c_client *c = &i2c_dev->client;
>> + void __iomem *reg = i2c_dev->base + STM32F4_I2C_CR2;
>> +
>> + if (c->count) {
>> + stm32f4_i2c_write_msg(i2c_dev);
>> + if (!c->count) {
>> + /* Disable BUF interrupt */
>> + stm32f4_i2c_clr_bits(reg, STM32F4_I2C_CR2_ITBUFEN);
>> + }
>> + } else {
>> + stm32f4_i2c_terminate_xfer(i2c_dev);
>> + }
>> +}
>> +
>> +/**
>> + * stm32f4_i2c_handle_tx_btf() - Handle byte transfer finished interrupt
>> + * in case of write
>> + * @i2c_dev: Controller's private data
>> + */
>> +static void stm32f4_i2c_handle_tx_btf(struct stm32f4_i2c_dev *i2c_dev)
>> +{
>> + struct stm32f4_i2c_client *c = &i2c_dev->client;
>> +
>> + if (c->count)
>> + stm32f4_i2c_write_msg(i2c_dev);
>> + else
>> + stm32f4_i2c_terminate_xfer(i2c_dev);
>> +}
> The two functions above look very similar.
> Isn't there a way to factorize?
Good point. Thanks. I will do it in the V2.
>
>> +
>> +/**
>> + * stm32f4_i2c_handle_read() - Handle FIFO enmpty interrupt in case of read
> s/enmpty/empty/
OK
>
>
> ...
>> +
>> +/**
>> + * stm32f4_i2c_xfer() - Transfer combined I2C message
>> + * @i2c_adap: Adapter pointer to the controller
>> + * @msgs: Pointer to data to be written.
>> + * @num: Number of messages to be executed
>> + */
>> +static int stm32f4_i2c_xfer(struct i2c_adapter *i2c_adap, struct i2c_msg msgs[],
>> + int num)
>> +{
>> + struct stm32f4_i2c_dev *i2c_dev = i2c_get_adapdata(i2c_adap);
>> + int ret, i;
>> +
>> + i2c_dev->busy = true;
>> +
>> + ret = clk_prepare_enable(i2c_dev->clk);
>> + if (ret) {
>> + dev_err(i2c_dev->dev, "Failed to prepare_enable clock\n");
>> + return ret;
>> + }
>> +
>> + stm32f4_i2c_hw_config(i2c_dev);
> Maybe you could call this only at probe and resume time?
> You would save some register accesses.
Yes of course, I have put this here for test purpose as I wanted to
switch between Standard to Fast mode without compile a new DT and
rebooting the board.
But thanks to device tree overlay, I could easily do it and now I
don't have any reason to set hw config for each transfer.
I will fix it in V2.
>
>> +
>> + for (i = 0; i < num && !ret; i++)
>> + ret = stm32f4_i2c_xfer_msg(i2c_dev, &msgs[i], i == 0,
>> + i == num - 1);
>> +
>> + clk_disable_unprepare(i2c_dev->clk);
>> +
>> + i2c_dev->busy = false;
>> +
>> + return (ret < 0) ? ret : i;
>> +}
>> +
>
> Thanks!
> Maxime
Thanks for your review
Cedric
More information about the linux-arm-kernel
mailing list