[PATCH 2/2] regulator: mt6397: Add buck change mode regulator interface for mt6397
Henry Chen
henryc.chen at mediatek.com
Wed May 11 02:12:09 PDT 2016
BUCKs of mt6397 have auto mode and pwm mode.
User can use regulator interfaces to control modes.
Signed-off-by: Henry Chen <henryc.chen at mediatek.com>
---
.../bindings/regulator/mt6397-regulator.txt | 22 +++++
drivers/regulator/mt6397-regulator.c | 95 +++++++++++++++++++---
2 files changed, 105 insertions(+), 12 deletions(-)
diff --git a/Documentation/devicetree/bindings/regulator/mt6397-regulator.txt b/Documentation/devicetree/bindings/regulator/mt6397-regulator.txt
index a42b1d6..d3167f2 100644
--- a/Documentation/devicetree/bindings/regulator/mt6397-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/mt6397-regulator.txt
@@ -7,6 +7,26 @@ Required properties:
The definition for each of these nodes is defined using the standard binding
for regulators at Documentation/devicetree/bindings/regulator/regulator.txt.
+The mt6397 buck supports two different operating modes: Fast and Normal
+Mode. Some regulators support the modes to be changed by the consumers during
+normal operation.
+
+The regulators that support the standard "regulator-allow-change-mode" property,
+changing their mode during normal operation are:
+ buck_vpca15, buck_vpca7, buck_vsramca15, buck_vsramca7, buck_vcore, buck_vgpu,
+ buck_vdrm, buck_vio18
+
+The possible values for "regulator-supported-modes" are:
+ 0: PWM mode, mapping to regulator fast mode, allow the
+ converter to remain in the PWM mode regardless of the load current, so
+ that the noise spectrum of the converter can be minimized for certain
+ highly-noise-sensitive handset applications.
+ 1: Auto mode, mapping to regulator normal mode, mode switch by current
+ loading. At light load currents, the converter automatically enters
+ PFM mode to save power and improve light load efficiency. At heavy
+ load currents, the converter automatically enters PWM mode to minimiz
+ the noise spectrum of the converter.
+
The valid names for regulators are::
BUCK:
buck_vpca15, buck_vpca7, buck_vsramca15, buck_vsramca7, buck_vcore, buck_vgpu,
@@ -30,6 +50,8 @@ Example:
regulator-max-microvolt = <1350000>;
regulator-ramp-delay = <12500>;
regulator-enable-ramp-delay = <200>;
+ regulator-allow-change-mode;
+ regulator-supported-modes = <0 1>;
};
mt6397_vpca7_reg: buck_vpca7 {
diff --git a/drivers/regulator/mt6397-regulator.c b/drivers/regulator/mt6397-regulator.c
index 17a5b6c..c6c6aa85 100644
--- a/drivers/regulator/mt6397-regulator.c
+++ b/drivers/regulator/mt6397-regulator.c
@@ -23,6 +23,9 @@
#include <linux/regulator/mt6397-regulator.h>
#include <linux/regulator/of_regulator.h>
+#define MT6397_BUCK_MODE_AUTO 0
+#define MT6397_BUCK_MODE_FORCE_PWM 1
+
/*
* MT6397 regulators' information
*
@@ -38,10 +41,14 @@ struct mt6397_regulator_info {
u32 vselon_reg;
u32 vselctrl_reg;
u32 vselctrl_mask;
+ u32 modeset_reg;
+ u32 modeset_mask;
+ u32 modeset_shift;
};
#define MT6397_BUCK(match, vreg, min, max, step, volt_ranges, enreg, \
- vosel, vosel_mask, voselon, vosel_ctrl) \
+ vosel, vosel_mask, voselon, vosel_ctrl, _modeset_reg, \
+ _modeset_shift) \
[MT6397_ID_##vreg] = { \
.desc = { \
.name = #vreg, \
@@ -62,6 +69,9 @@ struct mt6397_regulator_info {
.vselon_reg = voselon, \
.vselctrl_reg = vosel_ctrl, \
.vselctrl_mask = BIT(1), \
+ .modeset_reg = _modeset_reg, \
+ .modeset_mask = BIT(_modeset_shift), \
+ .modeset_shift = _modeset_shift \
}
#define MT6397_LDO(match, vreg, ldo_volt_table, enreg, enbit, vosel, \
@@ -145,6 +155,63 @@ static const u32 ldo_volt_table7[] = {
1300000, 1500000, 1800000, 2000000, 2500000, 2800000, 3000000, 3300000,
};
+static int mt6397_regulator_set_mode(struct regulator_dev *rdev,
+ unsigned int mode)
+{
+ struct mt6397_regulator_info *info = rdev_get_drvdata(rdev);
+ int ret, val;
+
+ switch (mode) {
+ case REGULATOR_MODE_FAST:
+ val = MT6397_BUCK_MODE_FORCE_PWM;
+ break;
+ case REGULATOR_MODE_NORMAL:
+ val = MT6397_BUCK_MODE_AUTO;
+ break;
+ default:
+ ret = -EINVAL;
+ goto err_mode;
+ }
+
+ dev_dbg(&rdev->dev, "mt6397 buck set_mode %#x, %#x, %#x, %#x\n",
+ info->modeset_reg, info->modeset_mask,
+ info->modeset_shift, val);
+
+ val <<= info->modeset_shift;
+ ret = regmap_update_bits(rdev->regmap, info->modeset_reg,
+ info->modeset_mask, val);
+err_mode:
+ if (ret != 0) {
+ dev_err(&rdev->dev,
+ "Failed to set mt6397 buck mode: %d\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static unsigned int mt6397_regulator_get_mode(struct regulator_dev *rdev)
+{
+ struct mt6397_regulator_info *info = rdev_get_drvdata(rdev);
+ int ret, regval;
+
+ ret = regmap_read(rdev->regmap, info->modeset_reg, ®val);
+ if (ret != 0) {
+ dev_err(&rdev->dev,
+ "Failed to get mt6397 buck mode: %d\n", ret);
+ return ret;
+ }
+
+ switch ((regval & info->modeset_mask) >> info->modeset_shift) {
+ case MT6397_BUCK_MODE_AUTO:
+ return REGULATOR_MODE_NORMAL;
+ case MT6397_BUCK_MODE_FORCE_PWM:
+ return REGULATOR_MODE_FAST;
+ default:
+ return -EINVAL;
+ }
+}
+
static int mt6397_get_status(struct regulator_dev *rdev)
{
int ret;
@@ -160,7 +227,7 @@ static int mt6397_get_status(struct regulator_dev *rdev)
return (regval & info->qi) ? REGULATOR_STATUS_ON : REGULATOR_STATUS_OFF;
}
-static struct regulator_ops mt6397_volt_range_ops = {
+static const struct regulator_ops mt6397_volt_range_ops = {
.list_voltage = regulator_list_voltage_linear_range,
.map_voltage = regulator_map_voltage_linear_range,
.set_voltage_sel = regulator_set_voltage_sel_regmap,
@@ -170,9 +237,11 @@ static struct regulator_ops mt6397_volt_range_ops = {
.disable = regulator_disable_regmap,
.is_enabled = regulator_is_enabled_regmap,
.get_status = mt6397_get_status,
+ .set_mode = mt6397_regulator_set_mode,
+ .get_mode = mt6397_regulator_get_mode,
};
-static struct regulator_ops mt6397_volt_table_ops = {
+static const struct regulator_ops mt6397_volt_table_ops = {
.list_voltage = regulator_list_voltage_table,
.map_voltage = regulator_map_voltage_iterate,
.set_voltage_sel = regulator_set_voltage_sel_regmap,
@@ -184,7 +253,7 @@ static struct regulator_ops mt6397_volt_table_ops = {
.get_status = mt6397_get_status,
};
-static struct regulator_ops mt6397_volt_fixed_ops = {
+static const struct regulator_ops mt6397_volt_fixed_ops = {
.list_voltage = regulator_list_voltage_linear,
.enable = regulator_enable_regmap,
.disable = regulator_disable_regmap,
@@ -196,28 +265,30 @@ static struct regulator_ops mt6397_volt_fixed_ops = {
static struct mt6397_regulator_info mt6397_regulators[] = {
MT6397_BUCK("buck_vpca15", VPCA15, 700000, 1493750, 6250,
buck_volt_range1, MT6397_VCA15_CON7, MT6397_VCA15_CON9, 0x7f,
- MT6397_VCA15_CON10, MT6397_VCA15_CON5),
+ MT6397_VCA15_CON10, MT6397_VCA15_CON5, MT6397_VCA15_CON2, 11),
MT6397_BUCK("buck_vpca7", VPCA7, 700000, 1493750, 6250,
buck_volt_range1, MT6397_VPCA7_CON7, MT6397_VPCA7_CON9, 0x7f,
- MT6397_VPCA7_CON10, MT6397_VPCA7_CON5),
+ MT6397_VPCA7_CON10, MT6397_VPCA7_CON5, MT6397_VPCA7_CON2, 8),
MT6397_BUCK("buck_vsramca15", VSRAMCA15, 700000, 1493750, 6250,
buck_volt_range1, MT6397_VSRMCA15_CON7, MT6397_VSRMCA15_CON9,
- 0x7f, MT6397_VSRMCA15_CON10, MT6397_VSRMCA15_CON5),
+ 0x7f, MT6397_VSRMCA15_CON10, MT6397_VSRMCA15_CON5,
+ MT6397_VSRMCA15_CON2, 8),
MT6397_BUCK("buck_vsramca7", VSRAMCA7, 700000, 1493750, 6250,
buck_volt_range1, MT6397_VSRMCA7_CON7, MT6397_VSRMCA7_CON9,
- 0x7f, MT6397_VSRMCA7_CON10, MT6397_VSRMCA7_CON5),
+ 0x7f, MT6397_VSRMCA7_CON10, MT6397_VSRMCA7_CON5,
+ MT6397_VSRMCA7_CON2, 8),
MT6397_BUCK("buck_vcore", VCORE, 700000, 1493750, 6250,
buck_volt_range1, MT6397_VCORE_CON7, MT6397_VCORE_CON9, 0x7f,
- MT6397_VCORE_CON10, MT6397_VCORE_CON5),
+ MT6397_VCORE_CON10, MT6397_VCORE_CON5, MT6397_VCORE_CON2, 8),
MT6397_BUCK("buck_vgpu", VGPU, 700000, 1493750, 6250, buck_volt_range1,
MT6397_VGPU_CON7, MT6397_VGPU_CON9, 0x7f,
- MT6397_VGPU_CON10, MT6397_VGPU_CON5),
+ MT6397_VGPU_CON10, MT6397_VGPU_CON5, MT6397_VGPU_CON2, 8),
MT6397_BUCK("buck_vdrm", VDRM, 800000, 1593750, 6250, buck_volt_range2,
MT6397_VDRM_CON7, MT6397_VDRM_CON9, 0x7f,
- MT6397_VDRM_CON10, MT6397_VDRM_CON5),
+ MT6397_VDRM_CON10, MT6397_VDRM_CON5, MT6397_VDRM_CON2, 8),
MT6397_BUCK("buck_vio18", VIO18, 1500000, 2120000, 20000,
buck_volt_range3, MT6397_VIO18_CON7, MT6397_VIO18_CON9, 0x1f,
- MT6397_VIO18_CON10, MT6397_VIO18_CON5),
+ MT6397_VIO18_CON10, MT6397_VIO18_CON5, MT6397_VIO18_CON2, 8),
MT6397_REG_FIXED("ldo_vtcxo", VTCXO, MT6397_ANALDO_CON0, 10, 2800000),
MT6397_REG_FIXED("ldo_va28", VA28, MT6397_ANALDO_CON1, 14, 2800000),
MT6397_LDO("ldo_vcama", VCAMA, ldo_volt_table1,
--
1.8.1.1.dirty
More information about the linux-arm-kernel
mailing list