[PATCH v7 2/2] memory: atmel-ebi: add DT bindings documentation

Boris Brezillon boris.brezillon at free-electrons.com
Tue May 10 01:04:48 PDT 2016


On Wed, 4 May 2016 15:35:47 +0200
Boris Brezillon <boris.brezillon at free-electrons.com> wrote:

> On Wed, 4 May 2016 08:06:10 -0500
> Rob Herring <robh at kernel.org> wrote:
> 
> > On Wed, May 4, 2016 at 4:38 AM, Boris Brezillon
> > <boris.brezillon at free-electrons.com> wrote:  
> > > Hi Rob,
> > >
> > > On Tue, 3 May 2016 14:11:04 -0500
> > > Rob Herring <robh at kernel.org> wrote:
> > >    
> > >> On Tue, May 3, 2016 at 11:51 AM, Boris Brezillon
> > >> <boris.brezillon at free-electrons.com> wrote:    
> > >> > Hi Rob,
> > >> >
> > >> > On Tue, 3 May 2016 11:40:19 -0500
> > >> > Rob Herring <robh at kernel.org> wrote:
> > >> >    
> > >> >> On Thu, Apr 28, 2016 at 02:03:27PM +0200, Boris Brezillon wrote:    
> > >> >> > The EBI (External Bus Interface) is used to access external peripherals
> > >> >> > (NOR, SRAM, NAND, and other specific devices like ethernet controllers).
> > >> >> > Each device is assigned a CS line and an address range and can have its
> > >> >> > own configuration (timings, access mode, bus width, ...).
> > >> >> > This driver provides a generic DT binding to configure a device according
> > >> >> > to its requirements.
> > >> >> > For specific device controllers (like the NAND one) the SMC timings
> > >> >> > should be configured by the controller driver through the matrix and smc
> > >> >> > syscon regmaps.    
> > 
> > [...]
> >   
> > >> >> > +EBI bus configuration associated with specific chip-select will be defined in
> > >> >> > +the configs subnode. This configs node will in turn contain several subnodes
> > >> >> > +named config-<cs-id>, each of them containing the following properties.    
> > >> >>
> > >> >> This is a bit unusual. Why not just part of the child device nodes?    
> > >> >
> > >> > Oh, come on! I reworked the binding because Mark complained about the
> > >> > previous binding which was doing exactly what you're suggesting. Can
> > >> > you please be consistent in your reviews...    
> > >>
> > >> No, Mark and I both have our opinions. Which part of this patch
> > >> explains the history?    
> > >
> > > Hm, it's in patch 1/2 (just dropped the cover letter, which might not
> > > be such a good idea).
> > >    
> > >> If the revision history is not in the patch, I'm
> > >> not looking at it.
> > >>
> > >> My issue with it this way is that it has invented yet another way to
> > >> describe timings. I would like to be consistent across external bus
> > >> descriptions, but we're not very consistent to begin with though. The
> > >> most common seems to be the way you first did it. But I agree that it
> > >> is kind of screwy to have an intermediate node unless the controller
> > >> itself has sub-blocks within it and is not the established way to
> > >> describe a bus with chip selects. I would either put the properties
> > >> directly in the child nodes (e.g. flash at 0,0) or put your config nodes
> > >> in the device node. I'd call it timings instead of config, but that's
> > >> just bikeshedding.    
> > >
> > > Well, it's not only describing timings (see atmel,bus-width,
> > > atmel,byte-access-type, ...), but I'm fine with either names :).
> > >    
> > >>
> > >> memory-controller at 1000 {
> > >>   ...
> > >>   flash at 0,0 {
> > >>     timings {
> > >>       ...
> > >>     };
> > >>   };
> > >> };    
> > >
> > > Okay. Mark, what do you think of this approach?
> > >
> > > Note that one of my previous version was defining timings directly in
> > > the EBI device node, and Arnd noted that doing so may cause problems
> > > if one of the EBI property (or the config/timing node name) conflict
> > > with the sub-device binding, which is why I decided to put the EBI
> > > config definitions in a separate subnode.    
> > 
> > You have vendor prefixes on all the properties so I don't think a
> > collision is really a problem. It's also an established pattern in
> > i.MX WEIM and OMAP GPMC (which are hiding in bindings/bus/) and I
> > prefer consistency.  
> 
> So let's summarize that.
> 
> memory-controller at 1000 {
> 	...
> 	flash at 0,0 {
> 		atmel,<ebi-prop-name> = <value>;
> 		...
> 		<flash-device-prop> = <value>;
> 	};
> };
> 
> Would everyone agree on this representation?
> 
> With this approach, it's a bit more complicated to detect the case
> where we want to keep bootloader/firmware config, but it should be
> doable (it's much more easier to test for the presence of a
> config/timing node than verifying that either all or none of the
> mandatory properties are here).
> 
> Still remains the problem mentioned by Jean-Jacques: what if the
> sub-device takes 2 CS lines. Should we apply the same setting to those
> slots?
> 

Rob, Mark, Arnd, can you take a decision regarding this binding? This
driver is floating around for quite some time, and we were asked to
rework the binding several times (in time in an opposite direction).

For the record, here is the thread I mentioned earlier [1]. In his
answer, Arnd suggests to put timing and bus config description
outside of the sub-device node. Mark recently complained about this
representation, which led me to the configs/config-X appraoch, and now
Rob suggests to go back to the first proposal.

I'm fine doing that, but can you please all confirm that you agree on
this binding?

Thanks,

Boris

[1]http://lists.infradead.org/pipermail/linux-arm-kernel/2013-December/222438.html

-- 
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com



More information about the linux-arm-kernel mailing list