[PATCH V6 07/13] PCI: Provide common functions for ECAM mapping
Jayachandran C
jchandra at broadcom.com
Thu May 5 02:24:20 PDT 2016
On Fri, Apr 29, 2016 at 1:31 PM, Jayachandran C <jchandra at broadcom.com> wrote:
> On Fri, Apr 29, 2016 at 3:17 AM, Bjorn Helgaas <helgaas at kernel.org> wrote:
>> On Fri, Apr 15, 2016 at 07:06:42PM +0200, Tomasz Nowicki wrote:
>>> From: Jayachandran C <jchandra at broadcom.com>
>>>
>>> Add config option PCI_GENERIC_ECAM and file drivers/pci/ecam.c to
>>> provide generic functions for accessing memory mapped PCI config space.
>>>
>>> The API is defined in drivers/pci/ecam.h and is written to replace the
>>> API in drivers/pci/host/pci-host-common.h. The file defines a new
>>> 'struct pci_config_window' to hold the information related to a PCI
>>> config area and its mapping. This structure is expected to be used as
>>> sysdata for controllers that have ECAM based mapping.
>>>
>>> Helper functions are provided to setup the mapping, free the mapping
>>> and to implement the map_bus method in 'struct pci_ops'
>>
>> Spec reference: PCI Express Base Specification, rev 3.0, sec 7.2.2.
>>
>>> Signed-off-by: Jayachandran C <jchandra at broadcom.com>
>>> ---
>>> drivers/pci/Kconfig | 3 ++
>>> drivers/pci/Makefile | 2 +
>>> drivers/pci/ecam.c | 137 +++++++++++++++++++++++++++++++++++++++++++++++++++
>>> drivers/pci/ecam.h | 61 +++++++++++++++++++++++
>>> 4 files changed, 203 insertions(+)
>>> create mode 100644 drivers/pci/ecam.c
>>> create mode 100644 drivers/pci/ecam.h
>>>
>>> diff --git a/drivers/pci/Kconfig b/drivers/pci/Kconfig
>>> index 209292e..e930d62 100644
>>> --- a/drivers/pci/Kconfig
>>> +++ b/drivers/pci/Kconfig
>>> @@ -83,6 +83,9 @@ config HT_IRQ
>>> config PCI_ATS
>>> bool
>>>
>>> +config PCI_GENERIC_ECAM
>>> + bool
>>
>> "PCI_ECAM" is enough, I think. It's defined by and required by the
>> spec unless there's some arch-specific interface. Plus, if I
>
> Ok. Looking at the comments I think I have to take out generic from
> all the names - will do this in next version.
>
>> understand correctly, this infrastructure supports non-generic ECAM
>> implementations as well, since the caller supplies "struct
>> pci_generic_ecam_ops *ops".
>
> Yes, the idea was to support ECAM with quirks (and CAM) on both
> 32 and 64 bit, otherwise it would be too trivial to have a separate
> implementation.
>
>>> config PCI_IOV
>>> bool "PCI IOV support"
>>> depends on PCI
>>> diff --git a/drivers/pci/Makefile b/drivers/pci/Makefile
>>> index 2154092..810aec8 100644
>>> --- a/drivers/pci/Makefile
>>> +++ b/drivers/pci/Makefile
>>> @@ -55,6 +55,8 @@ obj-$(CONFIG_PCI_SYSCALL) += syscall.o
>>>
>>> obj-$(CONFIG_PCI_STUB) += pci-stub.o
>>>
>>> +obj-$(CONFIG_PCI_GENERIC_ECAM) += ecam.o
>>> +
>>> obj-$(CONFIG_XEN_PCIDEV_FRONTEND) += xen-pcifront.o
>>>
>>> obj-$(CONFIG_OF) += of.o
>>> diff --git a/drivers/pci/ecam.c b/drivers/pci/ecam.c
>>> new file mode 100644
>>> index 0000000..ff04c01
>>> --- /dev/null
>>> +++ b/drivers/pci/ecam.c
>>> @@ -0,0 +1,137 @@
>>> +/*
>>> + * Copyright 2016 Broadcom
>>> + *
>>> + * This program is free software; you can redistribute it and/or modify
>>> + * it under the terms of the GNU General Public License, version 2, as
>>> + * published by the Free Software Foundation (the "GPL").
>>> + *
>>> + * This program is distributed in the hope that it will be useful, but
>>> + * WITHOUT ANY WARRANTY; without even the implied warranty of
>>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
>>> + * General Public License version 2 (GPLv2) for more details.
>>> + *
>>> + * You should have received a copy of the GNU General Public License
>>> + * version 2 (GPLv2) along with this source code.
>>> + */
>>> +
>>> +#include <linux/device.h>
>>> +#include <linux/io.h>
>>> +#include <linux/kernel.h>
>>> +#include <linux/module.h>
>>> +#include <linux/pci.h>
>>> +#include <linux/slab.h>
>>> +
>>> +#include "ecam.h"
>>> +
>>> +/*
>>> + * On 64 bit systems, we do a single ioremap for the whole config space
>>> + * since we have enough virtual address range available. On 32 bit, do an
>>> + * ioremap per bus.
>>> + */
>>> +static const bool per_bus_mapping = !config_enabled(CONFIG_64BIT);
>>> +
>>> +/*
>>> + * Create a PCI config space window
>>> + * - reserve mem region
>>> + * - alloc struct pci_config_window with space for all mappings
>>> + * - ioremap the config space
>>> + */
>>> +struct pci_config_window *pci_generic_ecam_create(struct device *dev,
>>> + phys_addr_t addr, u8 bus_start, u8 bus_end,
>>
>> Can you take pointers to struct resources here instead of addr,
>> bus_start, and bus_end? The caller probably has them already, and
>> then you could add a useful printk like:
>>
>> dev_info(dev, "ECAM for %pR at %pR\n", busn_res, mmio_res);
>>
>> Would have to be careful about the struct resource lifetimes though.
>
> Yes, I had thought of this. The reason I did not go down that path was
> that we are using request_mem_region() which takes the address
> and creates a resource .internally.
>
> Beyond that, as you noted, the ownership and lifetime is slightly
> more complex. Either the calling code has to allocate the
> resource and handoff, or the ecam code has to make a copy of
> the resource. I would go with copy since it is much more simple
> to use.
>
> Since resource based API seems to be preferred, I will switch
> to passing bus and mmio resource and will use
> request_resource_conflict() to allocate the ECAM mem region,
>
>> If you had the MMIO resource here, you could also do the range
>> checking you currently have in gen_pci_init() here instead, so all
>> callers could benefit.
>
> Ok.
>
>>> + struct pci_generic_ecam_ops *ops)
>>> +{
>>> + struct pci_config_window *cfg;
>>> + unsigned int bus_shift, bus_range, bsz, mapsz;
>>> + int i, nidx;
>>> + int err = -ENOMEM;
>>> +
>>> + if (bus_end < bus_start)
>>> + return ERR_PTR(-EINVAL);
>>> +
>>> + bus_shift = ops->bus_shift;
>>> + bus_range = bus_end - bus_start + 1;
>>> + bsz = 1 << bus_shift;
>>> + nidx = per_bus_mapping ? bus_range : 1;
>>> + mapsz = per_bus_mapping ? bsz : bus_range * bsz;
>>> + cfg = kzalloc(sizeof(*cfg) + nidx * sizeof(cfg->win[0]), GFP_KERNEL);
>>> + if (!cfg)
>>> + return ERR_PTR(-ENOMEM);
>>> +
>>> + cfg->bus_start = bus_start;
>>> + cfg->bus_end = bus_end;
>>> + cfg->ops = ops;
>>> +
>>> + if (!request_mem_region(addr, bus_range * bsz, "Configuration Space"))
>>> + goto err_exit;
>>> +
>>> + /* cfgaddr has to be set after request_mem_region */
>>> + cfg->cfgaddr = addr;
>>> +
>>> + for (i = 0; i < nidx; i++) {
>>> + cfg->win[i] = ioremap(addr + i * mapsz, mapsz);
>>> + if (!cfg->win[i])
>>> + goto err_exit;
>>> + }
>>> +
>>> + if (cfg->ops->init) {
>>> + err = cfg->ops->init(dev, cfg);
>>> + if (err)
>>> + goto err_exit;
>>> + }
>>> + return cfg;
>>> +
>>> +err_exit:
>>> + pci_generic_ecam_free(cfg);
>>> + return ERR_PTR(err);
>>> +}
>>> +
>>> +/*
>>> + * Free a config space mapping
>>> + */
>>
>> Superfluous comment.
>
> Ok, will trim comments to keep the ones that are useful.
>
>>> +void pci_generic_ecam_free(struct pci_config_window *cfg)
>>> +{
>>> + unsigned int bus_range;
>>> + int i, nidx;
>>> +
>>> + bus_range = cfg->bus_end - cfg->bus_start + 1;
>>> + nidx = per_bus_mapping ? bus_range : 1;
>>> + for (i = 0; i < nidx; i++)
>>> + if (cfg->win[i])
>>> + iounmap(cfg->win[i]);
>>> + if (cfg->cfgaddr)
>>> + release_mem_region(cfg->cfgaddr,
>>> + bus_range << cfg->ops->bus_shift);
>>> + kfree(cfg);
>>> +}
>>> +
>>> +/*
>>> + * Function to implement the pci_ops ->map_bus method
>>> + */
>>> +void __iomem *pci_generic_ecam_map_bus(struct pci_bus *bus, unsigned int devfn,
>>> + int where)
>>> +{
>>> + struct pci_config_window *cfg = bus->sysdata;
>>
>> I don't really like the use of bus->sysdata here, because sysdata is
>> explicitly arch-specific.
>>
>> But I guess we're in a bind right now: it'd be nice to save the cfg
>> pointer in struct pci_host_bridge, but you have to call
>> pci_generic_ecam_create() before the struct pci_host_bridge has been
>> allocated, and you have to pass the pointer into pci_scan_root_bus(),
>> and there's no generic way to do that yet.
>>
>> So I guess this will have to do for now.
>
> I could call the structure pci_ecam_sysdata instead of pci_config_window
> to make it clear that it is to be used as sysdata for ECAM based PCI host
> controllers.
>
> The current push (at least on ARM/ARM64) seems to be to make
> bus->sysdata controller specific and avoid arch specific sysdata.
>
>>> + unsigned int devfn_shift = cfg->ops->bus_shift - 8;
>>> + unsigned int busn = bus->number;
>>> + void __iomem *base;
>>> +
>>> + if (busn < cfg->bus_start || busn > cfg->bus_end)
>>> + return NULL;
>>> +
>>> + busn -= cfg->bus_start;
>>> + if (per_bus_mapping)
>>> + base = cfg->win[busn];
>>> + else
>>> + base = cfg->win[0] + (busn << cfg->ops->bus_shift);
>>> + return base + (devfn << devfn_shift) + where;
>>> +}
>>> +
>>> +/* default ECAM ops */
>>> +struct pci_generic_ecam_ops pci_generic_ecam_default_ops = {
>>
>> Using both "generic" and "default" seems overkill. Maybe just:
>>
>> struct pci_ecam_ops pci_generic_ecam_ops = { ... ?
>
> Ok.
>
>>> + .bus_shift = 20,
>>> + .pci_ops = {
>>> + .map_bus = pci_generic_ecam_map_bus,
>>> + .read = pci_generic_config_read,
>>> + .write = pci_generic_config_write,
>>> + }
>>> +};
>>> diff --git a/drivers/pci/ecam.h b/drivers/pci/ecam.h
>>> new file mode 100644
>>> index 0000000..34c0aba
>>> --- /dev/null
>>> +++ b/drivers/pci/ecam.h
>>> @@ -0,0 +1,61 @@
>>> +/*
>>> + * Copyright 2016 Broadcom
>>> + *
>>> + * This program is free software; you can redistribute it and/or modify
>>> + * it under the terms of the GNU General Public License, version 2, as
>>> + * published by the Free Software Foundation (the "GPL").
>>> + *
>>> + * This program is distributed in the hope that it will be useful, but
>>> + * WITHOUT ANY WARRANTY; without even the implied warranty of
>>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
>>> + * General Public License version 2 (GPLv2) for more details.
>>> + *
>>> + * You should have received a copy of the GNU General Public License
>>> + * version 2 (GPLv2) along with this source code.
>>> + */
>>> +#ifndef DRIVERS_PCI_ECAM_H
>>> +#define DRIVERS_PCI_ECAM_H
>>> +
>>> +#include <linux/kernel.h>
>>> +#include <linux/platform_device.h>
>>> +
>>> +/*
>>> + * struct to hold pci ops and bus shift of the config window
>>> + * for a PCI controller.
>>> + */
>>> +struct pci_config_window;
>>> +struct pci_generic_ecam_ops {
>>
>> "struct pci_ecam_ops"
>
> Ok.
>
>>> + unsigned int bus_shift;
>>> + struct pci_ops pci_ops;
>>> + int (*init)(struct device *,
>>> + struct pci_config_window *);
>>> +};
>>> +
>>> +/*
>>> + * struct to hold the mappings of a config space window. This
>>> + * will be allocated with enough entries in win[] to hold all
>>> + * the mappings for the bus range.
>>> + */
>>> +struct pci_config_window {
>>> + phys_addr_t cfgaddr;
>>> + u16 domain;
>>> + u8 bus_start;
>>> + u8 bus_end;
>>> + void *priv;
>>> + struct pci_generic_ecam_ops *ops;
>>> + void __iomem *win[0];
>>> +};
>>> +
>>> +/* create and free for pci_config_window */
>>
>> Superfluous comment.
>>
>>> +struct pci_config_window *pci_generic_ecam_create(struct device *dev,
>>> + phys_addr_t addr, u8 bus_start, u8 bus_end,
>>> + struct pci_generic_ecam_ops *ops);
>>> +void pci_generic_ecam_free(struct pci_config_window *cfg);
>>
>> "pci_ecam_create" and "pci_ecam_free"? I suspect you're going to call
>> these for flavors of ECAM that are definitely not "generic".
>>
>>> +/* map_bus when ->sysdata is an instance of pci_config_window */
>>> +void __iomem *pci_generic_ecam_map_bus(struct pci_bus *bus, unsigned int devfn,
>>> + int where);
>>> +/* default ECAM ops, bus shift 20, generic read and write */
>>> +extern struct pci_generic_ecam_ops pci_generic_ecam_default_ops;
>>> +
>>> +#endif
>
> Thanks for the review. The ECAM patchset can be merged separately
> if you do not want to tie it the ACPI changes.
>
> Please let me know how you want to proceed. Depending on that, I will
> either post it as a separate patchset or ask Tomasz to pick up my
> changes and post the ACPI patchset. again.
I have made the changes suggested here, and added one more
change to move from 'void __iomem *win[0]' to a union for
pci_config_window so that it can be embedded in other structures[1].
The changes are at https://github.com/jchandra-brcm/linux branch
arm64-acpi-pci-v4 so that Tomasz can add it to v7 of the ACPI/PCI
patches. I am not posting the changes here to avoid the impression
that there are clashing ACPI/PCI patchsets.
The branch also has an example patch for ACPI generic PCI root
using the new ECAM code. This also has the simpler domain
setting code for ACPI as well as fix for the ECAM address
calculation which came up during the earlier discussion.
JC.
[1] Minor API changes will be needed for embedding now.
This change will make it easier to merge with Arnd's host bridge
changes when that goes in.
More information about the linux-arm-kernel
mailing list