mx6ul: Finding a good place to configure SAI2_MCLK

[Shawn Guo]

On Mon, May 02, 2016 at 08:59:17PM -0300, Fabio Estevam wrote:
> Hi,
> 
> In order to get audio working on imx6ul-evk board we need to enable
> the SAI2 MCLK clock by setting bit 20 (SAI2_MCLK_DIR) of the
> IOMUXC_GPR_GPR1 register.
> 
> I am not sure where is the appropriate place to set this bit.
> 
> Doing like this works fine:
> 
> --- a/include/linux/mfd/syscon/imx6q-iomuxc-gpr.h
> +++ b/include/linux/mfd/syscon/imx6q-iomuxc-gpr.h
> @@ -447,5 +447,6 @@
>  #define IMX6UL_GPR1_ENET2_CLK_OUTPUT           (0x1 << 18)
>  #define IMX6UL_GPR1_ENET_CLK_DIR               (0x3 << 17)
>  #define IMX6UL_GPR1_ENET_CLK_OUTPUT            (0x3 << 17)
> +#define IMX6UL_GPR1_SAI2_MCLK_DIR              (0x1 << 20)
> 
> index a38b16b..92cfb0f 100644
> --- a/arch/arm/mach-imx/mach-imx6ul.c
> +++ b/arch/arm/mach-imx/mach-imx6ul.c
> @@ -56,6 +56,19 @@ static inline void imx6ul_enet_init(void)
>         imx6ul_enet_phy_init();
>  }
> 
> +static void __init imx6ul_mclk_init(void)
> +{
> +       struct regmap *gpr;
> +
> +       gpr = syscon_regmap_lookup_by_compatible("fsl,imx6ul-iomuxc-gpr");
> +       if (!IS_ERR(gpr))
> +               regmap_update_bits(gpr, IOMUXC_GPR1, IMX6UL_GPR1_SAI2_MCLK_DIR,
> +                                  IMX6UL_GPR1_SAI2_MCLK_DIR);
> +       else
> +               pr_err("failed to find fsl,imx6ul-iomux-gpr regmap\n");
> +
> +}
> +
>  static void __init imx6ul_init_machine(void)
>  {
>         struct device *parent;
> @@ -68,6 +81,7 @@ static void __init imx6ul_init_machine(void)
>         imx6ul_enet_init();
>         imx_anatop_init();
>         imx6ul_pm_init();
> +       imx6ul_mclk_init();
>  }
> 
> but it does not seem correct as this should be board specific. Should
> we call it only if the compatible string matches imx6sl-14x14-evk
> string? Looks like that will not scale as well.
> 
> Currently in arch/arm/mach-imx/mach-imx6ul.c we also have
> imx6ul_enet_clk_init() function which sets the ENET_CLK in the GPR1
> register.
> 
> IMHO this is not correct because not all mx6ul boards need such clock
> and then we need to change this too.
> 
> So where should we set the SAI2_MCLK_DIR bit of GPR1? Inside the SAI driver?

To me, it's the best if we can handle this in SAI driver.

Shawn

> 
> Appreciate some feedback.
> 
> Thanks,
> 
> Fabio Estevam
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel