[PATCH] usb: xhci-mtk: fixup mouse wakeup failure during system suspend

chunfeng yun chunfeng.yun at mediatek.com
Tue May 3 02:09:51 PDT 2016


On Tue, 2016-05-03 at 10:51 +0300, Felipe Balbi wrote:
> Hi,
> 
> chunfeng yun <chunfeng.yun at mediatek.com> writes:
> > On Thu, 2016-04-21 at 10:04 +0800, Chunfeng Yun wrote:
> >> Click mouse after xhci suspend completion but before system suspend
> >> completion, system will not be waken up by mouse if the duration of
> >> them is larger than 20ms which is the device UFP's resume signaling
> 
> what is "them" here ? The duration of what is longer than 20ms ?
They are "xhci suspend completion" and "system suspend completion";

It's time duration

> 
> >> lasted. Another reason is that the SPM is not enabled before system
> 
> what's SPM ?
It is System Power Management which is powered off when system is
running in normal mode, and is powered on when system enters suspend
mode. It is used to wakeup system when some wakeup sources, such as
bluetooth or powerkey etc, tigger wakeup event.

> 
> >> suspend compeltion, this causes SPM also not notice the resume signal.
>            ^^^^^^^^^^
>            completion
> 
> >> So in order to reduce the duration less than 20ms, make use of
> >> syscore's suspend/resume interface.
> 
> no, this is the wrong approach
But it seems only one workable approach from software side

> 
> >> In fact it is a work around solution which only reduces the
> >> probability of failure, because we can't ensure that the duration from
> >> syscore's suspend completion to SPM working is always less than 20ms.
> 
> right, which means you're not really fixing anything. Morevoer, you make
> it so that this won't work with multiple instances of the XHCI IP in
> your SoC.
> 
It can be easily fixed up from hardware side by latching resume signal
until SPM is powered on.

I forgot to take into account of multiple instances
 
> >> Because the syscore runs on irq disabled context, and xhci's
> >> suspend/resume calls some sleeping functions, enable local irq
> >> and then disable it during suspend/resume. This may be not a problem,
> >> since only boot CPU is runing.
> 
> another problem :) calling local_irq_{enable,disable}() is an indication
> that something's wrong.
Oh!

BTW: There will be warning logs if they are not called.

Thanks a lot
> 
> >> Signed-off-by: Chunfeng Yun <chunfeng.yun at mediatek.com>
> >> ---
> >>  drivers/usb/host/xhci-mtk.c |   31 ++++++++++++++++++++++++++++++-
> >>  1 file changed, 30 insertions(+), 1 deletion(-)
> >> 
> >> diff --git a/drivers/usb/host/xhci-mtk.c b/drivers/usb/host/xhci-mtk.c
> >> index 79959f1..8277f02 100644
> >> --- a/drivers/usb/host/xhci-mtk.c
> >> +++ b/drivers/usb/host/xhci-mtk.c
> >> @@ -28,6 +28,7 @@
> >>  #include <linux/pm_runtime.h>
> >>  #include <linux/regmap.h>
> >>  #include <linux/regulator/consumer.h>
> >> +#include <linux/syscore_ops.h>
> >>  
> >>  #include "xhci.h"
> >>  #include "xhci-mtk.h"
> >> @@ -490,6 +491,8 @@ static int xhci_mtk_setup(struct usb_hcd *hcd)
> >>  	return xhci_gen_setup(hcd, xhci_mtk_quirks);
> >>  }
> >>  
> >> +static struct device *xhci_mtk_syscore_dev;
> 
> now, what happens when you have more than one XHCI instance ?
> 





More information about the linux-arm-kernel mailing list