[PATCH 0/3] mxs-lradc: Add support for current sources

[Jonathan Cameron]

On 29/04/16 18:45, Harald Geyer wrote:
> Hi Stefan!
> 
> On 29.04.2016 17:12, Stefan Wahren wrote:
>> Hi Harald,
>>
>> Am 22.04.2016 um 15:52 schrieb Harald Geyer:
>>> Patch 1/3 changes the driver and updates the binding documentation
>>> (I guess it is still in staging.)
>>>
>>> Patches 2/3 and 3/3 add the devicetree nodes to imx23 and imx28 boards.
>>> I'd like to get input whether this is actually desired. On boards where
>>> these regulators would never be enabled this costs a few extra bytes of
>>> RAM for allocation of the device data, because the nodes can't be easily
>>> removed in .dts files which are including the .dtsi files. The alternative
>>> is to add the new nodes to many .dts files, which would be a lot code
>>> duplication.
>>
>> if i get it right the real intention of this patch series is to make the
>> mxs-lradc provide resistance values instead of voltages.
> 
> ... or even temperature values if a thermistor is connected.
> 
>> So how about
>> dropping the whole regulator stuff and provide the values as
>> IIO_RESISTANCE via iio interface?
> 
> Can you elaborate on this?
> 
> My thinking is that there should be a thermistor (or whatever else) driver,
> that is a consumer of the regulator and a consumer of the IIO_VOLTAGE
> iio channel and provides a new device with an IIO_RESISTANCE or IIO_TEMP
> channel. Maybe there is a simpler solution, that I'm missing?
I agree with that approach - need a way to describe the upstream hardware - so
will need a thermistor driver
> 
> Actually I'm not 100% happy with the above solution myself, because if we
> start supporting devices that act as an iio-multiplexer (some device that
> is an iio consumer and provides many new iio channels and can control
> via gpios which of it child channels is actually routed to the upstream
> device) I don't know how to properly manage the regulator device.
Hmm. Are you talking about muxing the regulator as well?  That will get
complex indeed.  Might be possible to cheat and imply the regulators are
always connected to all inputs...  or do you want to dynamically change
the regulator output?  That gets messy fast - though in theory might be
possible...
> However since this is only hypothetical ATM, I think we don't have to
> worry about this too much.
> 
>> Btw this feature should be only added to dts files where is actually used.
> 
> Ok, so how do we figure out which boards these are?
> I use this on the olinuxino and I guess all evaluation boards support the
> use case too. The others I don't know enough about to be sure and I guess
> it's not a good idea to just wait until somebody speaks up and complains
> that the feature is missing on board X ...
> 
> Thanks,
> Harald
> 
>> Regards
>> Stefan
>>
>>>
>>> Harald Geyer (3):
>>>   iio: mxs-lradc: Add regulators for current sources
>>>   ARM: dts: imx23: Provide regulators for the current sources of the
>>>     LRADC
>>>   ARM: dts: imx28: Provide regulators for the current sources of the
>>>     LRADC
>>>
>>>  .../bindings/staging/iio/adc/mxs-lradc.txt         |  29 ++++
>>>  arch/arm/boot/dts/imx23.dtsi                       |   8 ++
>>>  arch/arm/boot/dts/imx28.dtsi                       |   8 ++
>>>  drivers/iio/adc/Kconfig                            |   1 +
>>>  drivers/iio/adc/mxs-lradc.c                        | 152 +++++++++++++++++++++
>>>  5 files changed, 198 insertions(+)
>>>
>