[PATCH v5 27/46] regulator: pwm: adjust PWM config at probe time

Boris Brezillon boris.brezillon at free-electrons.com
Wed Mar 30 13:03:50 PDT 2016


The PWM attached to a PWM regulator device might have been previously
configured by the bootloader.
Make sure the bootloader and linux config are in sync, and adjust the PWM
config if that's not the case.

Signed-off-by: Boris Brezillon <boris.brezillon at free-electrons.com>
---
 drivers/regulator/pwm-regulator.c | 50 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 50 insertions(+)

diff --git a/drivers/regulator/pwm-regulator.c b/drivers/regulator/pwm-regulator.c
index 9154c47..9590fb0 100644
--- a/drivers/regulator/pwm-regulator.c
+++ b/drivers/regulator/pwm-regulator.c
@@ -240,6 +240,52 @@ static int pwm_regulator_init_continuous(struct platform_device *pdev,
 	return 0;
 }
 
+static int pwm_regulator_adjust_pwm_config(struct pwm_regulator_data *drvdata)
+{
+	struct pwm_state pstate = { };
+	struct pwm_args pargs = { };
+
+	pwm_get_args(drvdata->pwm, &pargs);
+	pwm_get_state(drvdata->pwm, &pstate);
+
+	/*
+	 * if the current period is zero this either means the PWM driver
+	 * does not support initial state retrieval or the PWM was not
+	 * configured.
+	 * In any case, we setup the new period and poloarity, and assign a
+	 * duty_cycle of 0.
+	 */
+	if (!pstate.period) {
+		pstate.duty_cycle = 0;
+		pstate.period = pargs.period;
+		pstate.polarity = pargs.polarity;
+
+		return pwm_apply_state(drvdata->pwm, &pstate);
+	}
+
+	/*
+	 * Adjust the PWM dutycycle/period based on the period value provided
+	 * in PWM args.
+	 */
+	if (pargs.period != pstate.period) {
+		u64 dutycycle = (u64)pstate.duty_cycle * pargs.period;
+
+		do_div(dutycycle, pstate.period);
+		pstate.duty_cycle = dutycycle;
+		pstate.period = pargs.period;
+	}
+
+	/*
+	 * If the polarity changed, we should also change the dutycycle value.
+	 */
+	if (pargs.polarity != pstate.polarity) {
+		pstate.polarity = pargs.polarity;
+		pstate.duty_cycle = pstate.period - pstate.duty_cycle;
+	}
+
+	return pwm_apply_state(drvdata->pwm, &pstate);
+}
+
 static int pwm_regulator_probe(struct platform_device *pdev)
 {
 	const struct regulator_init_data *init_data;
@@ -283,6 +329,10 @@ static int pwm_regulator_probe(struct platform_device *pdev)
 		return PTR_ERR(drvdata->pwm);
 	}
 
+	ret = pwm_regulator_adjust_pwm_config(drvdata);
+	if (ret)
+		return ret;
+
 	regulator = devm_regulator_register(&pdev->dev,
 					    &drvdata->desc, &config);
 	if (IS_ERR(regulator)) {
-- 
2.5.0




More information about the linux-arm-kernel mailing list