[PATCH] ARM: mvebu: fix GPIO config on the Linksys boards

[Imre Kaloz]

Hi guys,

Just noticed this never got neither merged or declined ;)

It should still apply, but if needed, I can refresh it and send a v2.


Best,

Imre

On Fri, 31 Jul 2015 20:42:00 +0200, Imre Kaloz <kaloz at openwrt.org> wrote:

> Some of the GPIO configs were wrong in the submitted DTS files,
> this patch fixes all affected boards.
>
> Signed-off-by: Imre Kaloz <kaloz at openwrt.org>
>
> Cc: <stable at vger.kernel.org> # v4.1 +
> ---
>  arch/arm/boot/dts/armada-385-linksys.dtsi     | 6 +++---
>  arch/arm/boot/dts/armada-xp-linksys-mamba.dts | 4 ++--
>  2 files changed, 5 insertions(+), 5 deletions(-)
>
> diff --git a/arch/arm/boot/dts/armada-385-linksys.dtsi  
> b/arch/arm/boot/dts/armada-385-linksys.dtsi
> index 74a9c6b..1b0075f 100644
> --- a/arch/arm/boot/dts/armada-385-linksys.dtsi
> +++ b/arch/arm/boot/dts/armada-385-linksys.dtsi
> @@ -243,7 +243,7 @@
>  		button at 2 {
>  			label = "Factory Reset Button";
>  			linux,code = <KEY_RESTART>;
> -			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
> +			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
>  		};
>  	};
> @@ -258,7 +258,7 @@
>  		};
> 		sata {
> -			gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>;
> +			gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
>  			default-state = "off";
>  		};
>  	};
> @@ -311,7 +311,7 @@
> &pinctrl {
>  	keys_pin: keys-pin {
> -		marvell,pins = "mpp24", "mpp47";
> +		marvell,pins = "mpp24", "mpp29";
>  		marvell,function = "gpio";
>  	};
> diff --git a/arch/arm/boot/dts/armada-xp-linksys-mamba.dts  
> b/arch/arm/boot/dts/armada-xp-linksys-mamba.dts
> index fdd187c..e767735 100644
> --- a/arch/arm/boot/dts/armada-xp-linksys-mamba.dts
> +++ b/arch/arm/boot/dts/armada-xp-linksys-mamba.dts
> @@ -302,13 +302,13 @@
>  		button at 1 {
>  			label = "WPS";
>  			linux,code = <KEY_WPS_BUTTON>;
> -			gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
> +			gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
>  		};
> 		button at 2 {
>  			label = "Factory Reset Button";
>  			linux,code = <KEY_RESTART>;
> -			gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
> +			gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
>  		};
>  	};