[PATCH v3 2/2] dmaengine: vdma: Fix race condition in Non-SG mode

Kedareswara rao Appana appana.durga.rao at xilinx.com
Fri Mar 25 02:16:39 PDT 2016


When VDMA is configured in  Non-sg mode
Users can queue descriptors greater than h/w configured frames.

Current driver allows the user to queue descriptors upto h/w configured.
Which is wrong for non-sg mode configuration.

This patch fixes this issue.

Signed-off-by: Kedareswara rao Appana <appanad at xilinx.com>
---
Changes for v3:
---> New patch.

 drivers/dma/xilinx/xilinx_vdma.c | 25 +++++++++++++++++++------
 1 file changed, 19 insertions(+), 6 deletions(-)

diff --git a/drivers/dma/xilinx/xilinx_vdma.c b/drivers/dma/xilinx/xilinx_vdma.c
index abe915c..b873d98 100644
--- a/drivers/dma/xilinx/xilinx_vdma.c
+++ b/drivers/dma/xilinx/xilinx_vdma.c
@@ -209,6 +209,7 @@ struct xilinx_vdma_tx_descriptor {
  * @flush_on_fsync: Flush on Frame sync
  * @desc_pendingcount: Descriptor pending count
  * @ext_addr: Indicates 64 bit addressing is supported by dma channel
+ * @desc_submitcount: Descriptor h/w submitted count
  */
 struct xilinx_vdma_chan {
 	struct xilinx_vdma_device *xdev;
@@ -233,6 +234,7 @@ struct xilinx_vdma_chan {
 	bool flush_on_fsync;
 	u32 desc_pendingcount;
 	bool ext_addr;
+	u32 desc_submitcount;
 };
 
 /**
@@ -716,9 +718,10 @@ static void xilinx_vdma_start_transfer(struct xilinx_vdma_chan *chan)
 		struct xilinx_vdma_tx_segment *segment, *last = NULL;
 		int i = 0;
 
-		list_for_each_entry(desc, &chan->pending_list, node) {
-			segment = list_first_entry(&desc->segments,
-					   struct xilinx_vdma_tx_segment, node);
+		if (chan->desc_submitcount < chan->num_frms)
+			i = chan->desc_submitcount;
+
+		list_for_each_entry(segment, &desc->segments, node) {
 			if (chan->ext_addr)
 				vdma_desc_write_64(chan,
 					XILINX_VDMA_REG_START_ADDRESS_64(i++),
@@ -742,8 +745,17 @@ static void xilinx_vdma_start_transfer(struct xilinx_vdma_chan *chan)
 		vdma_desc_write(chan, XILINX_VDMA_REG_VSIZE, last->hw.vsize);
 	}
 
-	list_splice_tail_init(&chan->pending_list, &chan->active_list);
-	chan->desc_pendingcount = 0;
+	if (!chan->has_sg) {
+		list_del(&desc->node);
+		list_add_tail(&desc->node, &chan->active_list);
+		chan->desc_submitcount++;
+		chan->desc_pendingcount--;
+		if (chan->desc_submitcount == chan->num_frms)
+			chan->desc_submitcount = 0;
+	} else {
+		list_splice_tail_init(&chan->pending_list, &chan->active_list);
+		chan->desc_pendingcount = 0;
+	}
 }
 
 /**
@@ -927,7 +939,8 @@ append:
 	list_add_tail(&desc->node, &chan->pending_list);
 	chan->desc_pendingcount++;
 
-	if (unlikely(chan->desc_pendingcount > chan->num_frms)) {
+	if (chan->has_sg &&
+	    unlikely(chan->desc_pendingcount > chan->num_frms)) {
 		dev_dbg(chan->dev, "desc pendingcount is too high\n");
 		chan->desc_pendingcount = chan->num_frms;
 	}
-- 
2.1.2




More information about the linux-arm-kernel mailing list