[PATCH 1/2] ARM: dts: ux500: use the GPIO DT header
Linus Walleij
linus.walleij at linaro.org
Thu Mar 24 07:51:19 PDT 2016
Use the <dt-bindings/gpio/gpio.h> header instead of using
hardcoded values for the GPIO flags. Eradicate the totally
bogus "0x4" flag used and set that to GPIO_ACTIVE_HIGH as is
proper, switch the inverted card detect on the Snowball to
flag using GPIO_ACTIVE_LOW instead of using the MMC-specific
inversion flag.
Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
---
arch/arm/boot/dts/ste-ccu9540.dts | 2 +-
arch/arm/boot/dts/ste-dbx5x0.dtsi | 1 +
arch/arm/boot/dts/ste-href-stuib.dtsi | 4 ++--
arch/arm/boot/dts/ste-href-tvk1281618.dtsi | 4 ++--
arch/arm/boot/dts/ste-hrefprev60.dtsi | 8 ++++----
arch/arm/boot/dts/ste-hrefv60plus.dtsi | 6 +++---
arch/arm/boot/dts/ste-snowball.dts | 19 +++++++++----------
7 files changed, 22 insertions(+), 22 deletions(-)
diff --git a/arch/arm/boot/dts/ste-ccu9540.dts b/arch/arm/boot/dts/ste-ccu9540.dts
index c8b815819cfe..b3b9bb8e1aa8 100644
--- a/arch/arm/boot/dts/ste-ccu9540.dts
+++ b/arch/arm/boot/dts/ste-ccu9540.dts
@@ -49,7 +49,7 @@
cap-mmc-highspeed;
vmmc-supply = <&ab8500_ldo_aux3_reg>;
- cd-gpios = <&gpio7 6 0x4>; // 230
+ cd-gpios = <&gpio7 6 GPIO_ACTIVE_HIGH>; // 230
cd-inverted;
status = "okay";
diff --git a/arch/arm/boot/dts/ste-dbx5x0.dtsi b/arch/arm/boot/dts/ste-dbx5x0.dtsi
index 341f5b7ed242..d85830d80252 100644
--- a/arch/arm/boot/dts/ste-dbx5x0.dtsi
+++ b/arch/arm/boot/dts/ste-dbx5x0.dtsi
@@ -12,6 +12,7 @@
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/mfd/dbx500-prcmu.h>
#include <dt-bindings/arm/ux500_pm_domains.h>
+#include <dt-bindings/gpio/gpio.h>
#include "skeleton.dtsi"
/ {
diff --git a/arch/arm/boot/dts/ste-href-stuib.dtsi b/arch/arm/boot/dts/ste-href-stuib.dtsi
index c3987ad06d79..6f720756057d 100644
--- a/arch/arm/boot/dts/ste-href-stuib.dtsi
+++ b/arch/arm/boot/dts/ste-href-stuib.dtsi
@@ -22,13 +22,13 @@
button at 139 {
/* Proximity sensor */
- gpios = <&gpio6 25 0x4>;
+ gpios = <&gpio6 25 GPIO_ACTIVE_HIGH>;
linux,code = <11>; /* SW_FRONT_PROXIMITY */
label = "SFH7741 Proximity Sensor";
};
button at 145 {
/* Hall sensor */
- gpios = <&gpio4 17 0x4>;
+ gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
linux,code = <0>; /* SW_LID */
label = "HED54XXU11 Hall Effect Sensor";
};
diff --git a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
index 55f9d0cc90f3..54d80da2a5df 100644
--- a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
+++ b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
@@ -24,13 +24,13 @@
button at 139 {
/* Proximity sensor */
- gpios = <&gpio6 25 0x4>;
+ gpios = <&gpio6 25 GPIO_ACTIVE_HIGH>;
linux,code = <11>; /* SW_FRONT_PROXIMITY */
label = "SFH7741 Proximity Sensor";
};
button at 145 {
/* Hall sensor */
- gpios = <&gpio4 17 0x4>;
+ gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
linux,code = <0>; /* SW_LID */
label = "HED54XXU11 Hall Effect Sensor";
};
diff --git a/arch/arm/boot/dts/ste-hrefprev60.dtsi b/arch/arm/boot/dts/ste-hrefprev60.dtsi
index b0278f4c486c..ece222d51717 100644
--- a/arch/arm/boot/dts/ste-hrefprev60.dtsi
+++ b/arch/arm/boot/dts/ste-hrefprev60.dtsi
@@ -18,7 +18,7 @@
/ {
gpio_keys {
button at 1 {
- gpios = <&tc3589x_gpio 7 0x4>;
+ gpios = <&tc3589x_gpio 7 GPIO_ACTIVE_HIGH>;
};
};
@@ -68,12 +68,12 @@
// External Micro SD slot
sdi0_per1 at 80126000 {
- cd-gpios = <&tc3589x_gpio 3 0x4>;
+ cd-gpios = <&tc3589x_gpio 3 GPIO_ACTIVE_HIGH>;
};
vmmci: regulator-gpio {
- gpios = <&tc3589x_gpio 18 0x4>;
- enable-gpio = <&tc3589x_gpio 17 0x4>;
+ gpios = <&tc3589x_gpio 18 GPIO_ACTIVE_HIGH>;
+ enable-gpio = <&tc3589x_gpio 17 GPIO_ACTIVE_HIGH>;
};
pinctrl {
diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
index 149a72e7e37a..45d7af326718 100644
--- a/arch/arm/boot/dts/ste-hrefv60plus.dtsi
+++ b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
@@ -20,12 +20,12 @@
soc {
// External Micro SD slot
sdi0_per1 at 80126000 {
- cd-gpios = <&gpio2 31 0x4>; // 95
+ cd-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>; // 95
};
vmmci: regulator-gpio {
- gpios = <&gpio0 5 0x4>;
- enable-gpio = <&gpio5 9 0x4>;
+ gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+ enable-gpio = <&gpio5 9 GPIO_ACTIVE_HIGH>;
};
pinctrl {
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index 08f82077b64d..36e84efc401c 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -50,35 +50,35 @@
wakeup-source;
linux,code = <2>;
label = "userpb";
- gpios = <&gpio1 0 0x4>;
+ gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
};
button at 2 {
debounce_interval = <50>;
wakeup-source;
linux,code = <3>;
label = "extkb1";
- gpios = <&gpio4 23 0x4>;
+ gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
};
button at 3 {
debounce_interval = <50>;
wakeup-source;
linux,code = <4>;
label = "extkb2";
- gpios = <&gpio4 24 0x4>;
+ gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
};
button at 4 {
debounce_interval = <50>;
wakeup-source;
linux,code = <5>;
label = "extkb3";
- gpios = <&gpio5 1 0x4>;
+ gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
};
button at 5 {
debounce_interval = <50>;
wakeup-source;
linux,code = <6>;
label = "extkb4";
- gpios = <&gpio5 2 0x4>;
+ gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>;
};
};
@@ -88,7 +88,7 @@
pinctrl-0 = <&gpioled_snowball_mode>;
used-led {
label = "user_led";
- gpios = <&gpio4 14 0x4>;
+ gpios = <&gpio4 14 GPIO_ACTIVE_HIGH>;
default-state = "on";
linux,default-trigger = "heartbeat";
};
@@ -155,8 +155,8 @@
vmmci: regulator-gpio {
compatible = "regulator-gpio";
- gpios = <&gpio7 4 0x4>;
- enable-gpio = <&gpio6 25 0x4>;
+ gpios = <&gpio7 4 GPIO_ACTIVE_HIGH>;
+ enable-gpio = <&gpio6 25 GPIO_ACTIVE_HIGH>;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2900000>;
@@ -182,8 +182,7 @@
pinctrl-0 = <&sdi0_default_mode>;
pinctrl-1 = <&sdi0_sleep_mode>;
- cd-gpios = <&gpio6 26 0x4>; // 218
- cd-inverted;
+ cd-gpios = <&gpio6 26 GPIO_ACTIVE_LOW>; // 218
status = "okay";
};
--
2.4.3
More information about the linux-arm-kernel
mailing list