[PATCH 1/2] ARM: dts: am335x: Add initial support for ICEv2 board

[Grygorii Strashko]

On 03/22/2016 08:37 AM, Lokesh Vutla wrote:
> TI's Industrial Communication Engine EVM is a low cost hardware mainly
> developed for industrial communication type applications using serial
> or Ethernet based interfaces. This platform features TI's AM3359 with
> 800MHz single core Cortex-A8 processor, 256MB DDR3, 64MB SPI flash,
> 8MB NOR Flash, mmc, usb, can, dual Ethernet ports.
> 
> For more information, look at HW user guide[1], Data manual[2].
> 
> Just add basic support for the moment.
> 
> [1] http://processors.wiki.ti.com/index.php/AM335x_Industrial_Communication_Engine_EVM_Rev2_1_HW_User_Guide
> [2] http://www.ti.com/lit/ds/symlink/am3359.pdf
> 
> Signed-off-by: Lokesh Vutla <lokeshvutla at ti.com>
> ---
>   .../devicetree/bindings/arm/omap/omap.txt          |   3 +
>   arch/arm/boot/dts/Makefile                         |   1 +
>   arch/arm/boot/dts/am335x-icev2.dts                 | 303 +++++++++++++++++++++
>   3 files changed, 307 insertions(+)
>   create mode 100644 arch/arm/boot/dts/am335x-icev2.dts
> 
> diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
> index 21e71a5..20f6d71 100644
> --- a/Documentation/devicetree/bindings/arm/omap/omap.txt
> +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
> @@ -133,6 +133,9 @@ Boards:
>   - AM335X Bone : Low cost community board
>     compatible = "ti,am335x-bone", "ti,am33xx", "ti,omap3"
>   
> +- AM3359 ICEv2 : Low cost Industrial Communication Engine EVM.
> +  compatible = "ti,am3359-icev2", "ti,am33xx", "ti,omap3"
> +
>   - AM335X OrionLXm : Substation Automation Platform
>     compatible = "novatech,am335x-lxm", "ti,am33xx"
>   
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 52b34a0..7dcf55e 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -486,6 +486,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \
>   	am335x-cm-t335.dtb \
>   	am335x-evm.dtb \
>   	am335x-evmsk.dtb \
> +	am335x-icev2.dtb \
>   	am335x-lxm.dtb \
>   	am335x-nano.dtb \
>   	am335x-pepper.dtb \
> diff --git a/arch/arm/boot/dts/am335x-icev2.dts b/arch/arm/boot/dts/am335x-icev2.dts
> new file mode 100644
> index 0000000..59c91e8
> --- /dev/null
> +++ b/arch/arm/boot/dts/am335x-icev2.dts
> @@ -0,0 +1,303 @@
> +/*
> + * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +/*
> + * AM335x ICE V2 board
> + * http://www.ti.com/tool/tmdsice3359
> + */
> +
> +/dts-v1/;
> +
> +#include "am33xx.dtsi"
> +
> +/ {
> +	model = "TI AM3359 ICE-V2";
> +	compatible = "ti,am3359-icev2", "ti,am33xx";
> +
> +	memory {
> +		device_type = "memory";
> +		reg = <0x80000000 0x10000000>; /* 256 MB */
> +	};
> +
> +	vbat: fixedregulator at 0 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vbat";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-boot-on;
> +	};
> +
> +	vtt_fixed: fixedregulator at 1 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vtt";
> +		regulator-min-microvolt = <1500000>;
> +		regulator-max-microvolt = <1500000>;
> +		gpio = <&gpio0 18 GPIO_ACTIVE_HIGH>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +		enable-active-high;
> +	};
> +
> +	leds {

Could you split this node on two leds at 0 and led at 1 and and move
all tpic2810 leds under leds0 and  all gpio leds under leds at 1?

otherwise gpio leds will not work because tpic2810 is
configured as module and so leds-gpio will be deferred until
tpic2810 is loaded (but it can be never loaded ;)

led at x numeration has to be started from 0 for each leds at Y.

> +		compatible = "gpio-leds";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&user_leds>;
> +
> +		led at 0 {
> +			label = "out0";
> +			gpios = <&tpic2810 0 GPIO_ACTIVE_HIGH>;
> +			default-state = "off";
> +		};
> +

[...]

> +		/* Tricolor status LEDs */
> +		led at 8 {
> +			label = "status0:red:cpu0";
> +			gpios = <&gpio0 17 GPIO_ACTIVE_HIGH>;
> +			default-state = "off";
> +			linux,default-trigger = "cpu0";
> +		};
> +

[...]

> 


-- 
regards,
-grygorii