[linux-sunxi] Re: [PATCH 0/4] Add AXP209 GPIO driver
maxime.ripard at free-electrons.com
Tue Mar 22 00:22:14 PDT 2016
On Wed, Mar 09, 2016 at 04:44:01PM +0100, Hans de Goede wrote:
> On 09-03-16 16:28, Maxime Ripard wrote:
> >On Wed, Mar 09, 2016 at 01:17:50PM +0100, Hans de Goede wrote:
> >>On 09-03-16 11:50, Maxime Ripard wrote:
> >>>The axp209 PMIC used in combination to some Allwinner SoCs has a bunch
> >>>of GPIOs accessible. Some boards use these to control their backlight
> >>>or a few LEDs.
> >>Thanks for working on this, but IMHO this cannot go upstream like this,
> >>the gpio pins on the axp pmics need a pinctrl driver, not a gpio
> >>driver. I.E. on the axp209 gpio0 and gpio1 can also be used to output
> >>an additional low-noise ldo (so as a regulator), or as an adc input.
> >Eventually, yes, it needs both. But they don't even have to be the
> >same driver, since they provide two different features. The only
> >reason we have that construct in the pio case is because they share
> >the same address space, but in the AXP case, the regmap and our mfd
> >take care of that already.
> Hmm, so your suggesting to have mfd instantiate 2 platform devices
> for this, a gpio and a pinctrl device, each with their own
> driver. Yes that would work, but I'm a bit worried about the 2
> racing or some such since they both will end up touching
> bit 0-2 of register 0x90 / 0x92, more-over since they are both
> touching the exact same bits I've the feeling that this really
> should be one driver.
I don't think that's an issue. We basically have two cases here:
either we have a driver using the pin or not.
If we have a driver using it, then pinctrl will make sure we have an
exclusive use of the pin, before the gpio is requested and we start
changing that value. If not, then no one cares anyway.
> I guess that in a proper written dts we either use pinctrl to enable
> a special function, or gpio, but still.
> >>I've been working on gsl1680 touchscreen support lately and on at least
> >>a few a23 tablets, the low-noise ldo is used as AVCC for the touchscreen
> >Yeah, the AXP209 also has an ADC connected to these pins.
> >>Now these use an axp223 pmic, but nothing is stopping someone from
> >>doing something similar with an axp209 and I think it would be best
> >>to support this from day one, rather then hope we can retro-fit this
> >>later without breaking dts.
> >I considered that, but I don't see how it would break the DT later. If
> >someone wants to enable say the ADC, he will of course have to add the
> >pinctrl driver, and the pinctrl handles, but the old DT will only
> >reference the gpio driver directly, which would still be something
> >that would work.
> I was assuming we would use one mfd-child(-platform)-device for this,
> not two. I guess that with 2 devices you're right and there should
> not be any problem, still as said it feels wrong-ish to have 2 drivers
> poking bits 0-2 of reg 0x90 / reg 0x92.
Note that the PIO is built on the same model and it works, while we
have 3 drivers in one. The only reason why we have everything linked
to the same device is because we have to share the address space, but
regmap takes care of that here.
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
-------------- next part --------------
A non-text attachment was scrubbed...
Size: 819 bytes
Desc: Digital signature
More information about the linux-arm-kernel