[PATCH v14 11/17] drm: bridge: analogix/dp: add some rk3288 special registers setting

Caesar Wang caesar.upstream at gmail.com
Thu Mar 17 23:56:05 PDT 2016



在 2016年02月15日 19:10, Yakir Yang 写道:
> RK3288 need some special registers setting, we can separate
> them out by the dev_type of plat_data.
>
> Signed-off-by: Yakir Yang <ykk at rock-chips.com>

Tested-by: Caesar Wang <wxt at rock-chips.com>

> ---
> Changes in v14: None
> Changes in v13: None
> Changes in v12: None
> Changes in v11: None
> Changes in v10: None
> Changes in v9: None
> Changes in v8: None
> Changes in v7: None
> Changes in v6: None
> Changes in v5: None
> Changes in v4: None
> Changes in v3: None
> Changes in v2:
> - Fix compile failed dut to phy_pd_addr variable misspell error
>
>   drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c | 76 ++++++++++++++---------
>   drivers/gpu/drm/bridge/analogix/analogix_dp_reg.h | 12 ++++
>   2 files changed, 60 insertions(+), 28 deletions(-)
>
> diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
> index 3858df5..1e24b37 100644
> --- a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
> +++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
> @@ -15,6 +15,8 @@
>   #include <linux/delay.h>
>   #include <linux/gpio.h>
>   
> +#include <drm/bridge/analogix_dp.h>
> +
>   #include "analogix_dp_core.h"
>   #include "analogix_dp_reg.h"
>   
> @@ -72,6 +74,14 @@ void analogix_dp_init_analog_param(struct analogix_dp_device *dp)
>   	reg = SEL_24M | TX_DVDD_BIT_1_0625V;
>   	writel(reg, dp->reg_base + ANALOGIX_DP_ANALOG_CTL_2);
>   
> +	if (dp->plat_data && (dp->plat_data->dev_type == RK3288_DP)) {
> +		writel(REF_CLK_24M, dp->reg_base + ANALOGIX_DP_PLL_REG_1);
> +		writel(0x95, dp->reg_base + ANALOGIX_DP_PLL_REG_2);
> +		writel(0x40, dp->reg_base + ANALOGIX_DP_PLL_REG_3);
> +		writel(0x58, dp->reg_base + ANALOGIX_DP_PLL_REG_4);
> +		writel(0x22, dp->reg_base + ANALOGIX_DP_PLL_REG_5);
> +	}
> +

In general, I will say what's mean for the number.

Okay that's the rk3288 special registers setting.

>   	reg = DRIVE_DVDD_BIT_1_0625V | VCO_BIT_600_MICRO;
>   	writel(reg, dp->reg_base + ANALOGIX_DP_ANALOG_CTL_3);
>   
> @@ -206,81 +216,85 @@ void analogix_dp_set_analog_power_down(struct analogix_dp_device *dp,
>   				       bool enable)
>   {
>   	u32 reg;
> +	u32 phy_pd_addr = ANALOGIX_DP_PHY_PD;
> +
> +	if (dp->plat_data && (dp->plat_data->dev_type == RK3288_DP))
> +		phy_pd_addr = ANALOGIX_DP_PD;
>   
>   	switch (block) {
>   	case AUX_BLOCK:
>   		if (enable) {
> -			reg = readl(dp->reg_base + ANALOGIX_DP_PHY_PD);
> +			reg = readl(dp->reg_base + phy_pd_addr);
>   			reg |= AUX_PD;
> -			writel(reg, dp->reg_base + ANALOGIX_DP_PHY_PD);
> +			writel(reg, dp->reg_base + phy_pd_addr);
>   		} else {
> -			reg = readl(dp->reg_base + ANALOGIX_DP_PHY_PD);
> +			reg = readl(dp->reg_base + phy_pd_addr);
>   			reg &= ~AUX_PD;
> -			writel(reg, dp->reg_base + ANALOGIX_DP_PHY_PD);
> +			writel(reg, dp->reg_base + phy_pd_addr);
>   		}
>   		break;
>   	case CH0_BLOCK:
>   		if (enable) {
> -			reg = readl(dp->reg_base + ANALOGIX_DP_PHY_PD);
> +			reg = readl(dp->reg_base + phy_pd_addr);
>   			reg |= CH0_PD;
> -			writel(reg, dp->reg_base + ANALOGIX_DP_PHY_PD);
> +			writel(reg, dp->reg_base + phy_pd_addr);
>   		} else {
> -			reg = readl(dp->reg_base + ANALOGIX_DP_PHY_PD);
> +			reg = readl(dp->reg_base + phy_pd_addr);
>   			reg &= ~CH0_PD;
> -			writel(reg, dp->reg_base + ANALOGIX_DP_PHY_PD);
> +			writel(reg, dp->reg_base + phy_pd_addr);
>   		}
>   		break;
>   	case CH1_BLOCK:
>   		if (enable) {
> -			reg = readl(dp->reg_base + ANALOGIX_DP_PHY_PD);
> +			reg = readl(dp->reg_base + phy_pd_addr);
>   			reg |= CH1_PD;
> -			writel(reg, dp->reg_base + ANALOGIX_DP_PHY_PD);
> +			writel(reg, dp->reg_base + phy_pd_addr);
>   		} else {
> -			reg = readl(dp->reg_base + ANALOGIX_DP_PHY_PD);
> +			reg = readl(dp->reg_base + phy_pd_addr);
>   			reg &= ~CH1_PD;
> -			writel(reg, dp->reg_base + ANALOGIX_DP_PHY_PD);
> +			writel(reg, dp->reg_base + phy_pd_addr);
>   		}
>   		break;
>   	case CH2_BLOCK:
>   		if (enable) {
> -			reg = readl(dp->reg_base + ANALOGIX_DP_PHY_PD);
> +			reg = readl(dp->reg_base + phy_pd_addr);
>   			reg |= CH2_PD;
> -			writel(reg, dp->reg_base + ANALOGIX_DP_PHY_PD);
> +			writel(reg, dp->reg_base + phy_pd_addr);
>   		} else {
> -			reg = readl(dp->reg_base + ANALOGIX_DP_PHY_PD);
> +			reg = readl(dp->reg_base + phy_pd_addr);
>   			reg &= ~CH2_PD;
> -			writel(reg, dp->reg_base + ANALOGIX_DP_PHY_PD);
> +			writel(reg, dp->reg_base + phy_pd_addr);
>   		}
>   		break;
>   	case CH3_BLOCK:
>   		if (enable) {
> -			reg = readl(dp->reg_base + ANALOGIX_DP_PHY_PD);
> +			reg = readl(dp->reg_base + phy_pd_addr);
>   			reg |= CH3_PD;
> -			writel(reg, dp->reg_base + ANALOGIX_DP_PHY_PD);
> +			writel(reg, dp->reg_base + phy_pd_addr);
>   		} else {
> -			reg = readl(dp->reg_base + ANALOGIX_DP_PHY_PD);
> +			reg = readl(dp->reg_base + phy_pd_addr);
>   			reg &= ~CH3_PD;
> -			writel(reg, dp->reg_base + ANALOGIX_DP_PHY_PD);
> +			writel(reg, dp->reg_base + phy_pd_addr);
>   		}
>   		break;
>   	case ANALOG_TOTAL:
>   		if (enable) {
> -			reg = readl(dp->reg_base + ANALOGIX_DP_PHY_PD);
> +			reg = readl(dp->reg_base + phy_pd_addr);
>   			reg |= DP_PHY_PD;
> -			writel(reg, dp->reg_base + ANALOGIX_DP_PHY_PD);
> +			writel(reg, dp->reg_base + phy_pd_addr);
>   		} else {
> -			reg = readl(dp->reg_base + ANALOGIX_DP_PHY_PD);
> +			reg = readl(dp->reg_base + phy_pd_addr);
>   			reg &= ~DP_PHY_PD;
> -			writel(reg, dp->reg_base + ANALOGIX_DP_PHY_PD);
> +			writel(reg, dp->reg_base + phy_pd_addr);
>   		}
>   		break;
>   	case POWER_ALL:
>   		if (enable) {
>   			reg = DP_PHY_PD | AUX_PD | CH3_PD | CH2_PD |
>   				CH1_PD | CH0_PD;
> -			writel(reg, dp->reg_base + ANALOGIX_DP_PHY_PD);
> +			writel(reg, dp->reg_base + phy_pd_addr);
>   		} else {
> -			writel(0x00, dp->reg_base + ANALOGIX_DP_PHY_PD);
> +			writel(0x00, dp->reg_base + phy_pd_addr);
>   		}
>   		break;
>   	default:
> @@ -399,8 +413,14 @@ void analogix_dp_init_aux(struct analogix_dp_device *dp)
>   	analogix_dp_reset_aux(dp);
>   
>   	/* Disable AUX transaction H/W retry */
> -	reg = AUX_BIT_PERIOD_EXPECTED_DELAY(3) | AUX_HW_RETRY_COUNT_SEL(0) |
> -	      AUX_HW_RETRY_INTERVAL_600_MICROSECONDS;
> +	if (dp->plat_data && (dp->plat_data->dev_type == RK3288_DP))
> +		reg = AUX_BIT_PERIOD_EXPECTED_DELAY(0) |
> +		      AUX_HW_RETRY_COUNT_SEL(3) |
> +		      AUX_HW_RETRY_INTERVAL_600_MICROSECONDS;
> +	else
> +		reg = AUX_BIT_PERIOD_EXPECTED_DELAY(3) |
> +		      AUX_HW_RETRY_COUNT_SEL(0) |
> +		      AUX_HW_RETRY_INTERVAL_600_MICROSECONDS;
>   	writel(reg, dp->reg_base + ANALOGIX_DP_AUX_HW_RETRY_CTL);
>   
>   	/* Receive AUX Channel DEFER commands equal to DEFFER_COUNT*64 */
> diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.h b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.h
> index 738db4c..337912b 100644
> --- a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.h
> +++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.h
> @@ -22,6 +22,14 @@
>   #define ANALOGIX_DP_VIDEO_CTL_8			0x3C
>   #define ANALOGIX_DP_VIDEO_CTL_10		0x44
>   
> +#define ANALOGIX_DP_PLL_REG_1			0xfc
> +#define ANALOGIX_DP_PLL_REG_2			0x9e4
> +#define ANALOGIX_DP_PLL_REG_3			0x9e8
> +#define ANALOGIX_DP_PLL_REG_4			0x9ec
> +#define ANALOGIX_DP_PLL_REG_5			0xa00
> +
> +#define ANALOGIX_DP_PD				0x12c
> +
>   #define ANALOGIX_DP_LANE_MAP			0x35C
>   
>   #define ANALOGIX_DP_ANALOG_CTL_1		0x370
> @@ -154,6 +162,10 @@
>   #define VSYNC_POLARITY_CFG			(0x1 << 1)
>   #define HSYNC_POLARITY_CFG			(0x1 << 0)
>   
> +/* ANALOGIX_DP_PLL_REG_1 */
> +#define REF_CLK_24M				(0x1 << 1)
> +#define REF_CLK_27M				(0x0 << 1)
> +
>   /* ANALOGIX_DP_LANE_MAP */
>   #define LANE3_MAP_LOGIC_LANE_0			(0x0 << 6)
>   #define LANE3_MAP_LOGIC_LANE_1			(0x1 << 6)


-- 
Thanks,
Caesar




More information about the linux-arm-kernel mailing list