[PATCH v4 2/2] power: reset: at91-shdwc: add new shutdown controller driver

Nicolas Ferre nicolas.ferre at atmel.com
Wed Mar 16 04:36:56 PDT 2016


Le 14/03/2016 21:22, Alexandre Belloni a écrit :
> On 10/03/2016 at 16:37:40 +0100, Nicolas Ferre wrote :
>> +ATMEL AT91 Alternative Shutdown Controller
> 
> Can't that be sama5d2 instead of alternative?
> 
>> +M:	Nicolas Ferre <nicolas.ferre at atmel.com>
>> +S:	Supported
>> +F:	drivers/power/reset/at91-shdwc.c
> 
> I would also use that in the filename. Because once there is a third
> shdwc, I'm not sure how you will be able to name it.
> 
>> +config POWER_RESET_AT91_SHDWC
> 
> I would also include that in the config name.
> 
>> +	tristate "Atmel AT91 shutdown controller driver"
>> +	depends on ARCH_AT91 || COMPILE_TEST
>> +	default SOC_SAMA5
>> +	help
>> +	  This driver supports the alternate shutdown controller for some Atmel
>> +	  SAMA5 SoCs. It is present for example on SAMA5D2 SoC.
>> +
> 
>> +#include <linux/clk.h>
>> +#include <linux/io.h>
>> +#include <linux/module.h>
>> +#include <linux/of.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/printk.h>
>> +
>> +#define SLOW_CLOCK_FREQ	32768
>> +
>> +#define AT91_SHDW_CR	0x00		/* Shut Down Control Register */
>> +#define AT91_SHDW_SHDW		BIT(0)			/* Shut Down command */
>> +#define AT91_SHDW_KEY		(0xa5UL << 24)		/* KEY Password */
>> +
>> +#define AT91_SHDW_MR	0x04		/* Shut Down Mode Register */
>> +#define AT91_SHDW_WKUPDBC_SHIFT	24
>> +#define AT91_SHDW_WKUPDBC_MASK	GENMASK(31, 16)
>> +#define AT91_SHDW_WKUPDBC(x)	(((x) << AT91_SHDW_WKUPDBC_SHIFT) \
>> +						& AT91_SHDW_WKUPDBC_MASK)
>> +
>> +#define AT91_SHDW_SR	0x08		/* Shut Down Status Register */
>> +#define AT91_SHDW_WKUPIS_SHIFT	16
>> +#define AT91_SHDW_WKUPIS_MASK	GENMASK(31, 16)
>> +#define AT91_SHDW_WKUPIS(x)	((1 << (x)) << AT91_SHDW_WKUPIS_SHIFT \
>> +						& AT91_SHDW_WKUPIS_MASK)
>> +
>> +#define AT91_SHDW_WUIR	0x0c		/* Shutdown Wake-up Inputs Register */
>> +#define AT91_SHDW_WKUPEN_MASK	GENMASK(15, 0)
>> +#define AT91_SHDW_WKUPEN(x)	((1 << (x)) & AT91_SHDW_WKUPEN_MASK)
>> +#define AT91_SHDW_WKUPT_SHIFT	16
>> +#define AT91_SHDW_WKUPT_MASK	GENMASK(31, 16)
>> +#define AT91_SHDW_WKUPT(x)	((1 << (x)) << AT91_SHDW_WKUPT_SHIFT \
>> +						& AT91_SHDW_WKUPT_MASK)
>> +
>> +#define SHDW_WK_PIN(reg, cfg)	((reg) & AT91_SHDW_WKUPIS((cfg)->wkup_pin_input))
>> +#define SHDW_RTCWK(reg, cfg)	(((reg) >> ((cfg)->sr_rtcwk_shift)) & 0x1)
>> +#define SHDW_RTCWKEN(cfg)	(1 << ((cfg)->mr_rtcwk_shift))
>> +
>> +#define DBC_PERIOD_US(x)	DIV_ROUND_UP_ULL((1000000 * (x)), \
>> +							SLOW_CLOCK_FREQ)
>> +
>> +struct shdwc_config {
>> +	u8 wkup_pin_input;
>> +	u8 mr_rtcwk_shift;
>> +	u8 sr_rtcwk_shift;
>> +};
>> +
>> +struct shdwc {
>> +	struct shdwc_config *cfg;
>> +	void __iomem *at91_shdwc_base;
>> +};
>> +
>> +/*
>> + * Hold configuration here, cannot be more than one instance of the driver
>> + * since pm_power_off itself is global.
>> + */
>> +static struct shdwc *at91_shdwc;
>> +static struct clk *sclk;
>> +
>> +static const unsigned long long sdwc_dbc_period[] = {
>> +	0, 3, 32, 512, 4096, 32768,
>> +};
>> +
>> +static void __init at91_wakeup_status(struct platform_device *pdev)
>> +{
>> +	struct shdwc *shdw = platform_get_drvdata(pdev);
>> +	u32 reg;
>> +	char *reason = "unknown";
>> +
>> +	reg = readl(shdw->at91_shdwc_base + AT91_SHDW_SR);
>> +
>> +	dev_dbg(&pdev->dev, "%s: status = %#x\n", __func__, reg);
>> +
>> +	/* Simple power-on, just bail out */
>> +	if (!reg)
>> +		return;
>> +
>> +	if (SHDW_WK_PIN(reg, shdw->cfg))
>> +		reason = "WKUP pin";
>> +	else if (SHDW_RTCWK(reg, shdw->cfg))
>> +		reason = "RTC";
>> +
>> +	pr_info("AT91: Wake-Up source: %s\n", reason);
>> +}
>> +
>> +static void at91_poweroff(void)
>> +{
>> +	writel(AT91_SHDW_KEY | AT91_SHDW_SHDW,
>> +			at91_shdwc->at91_shdwc_base + AT91_SHDW_CR);
> 
> This is still not properly aligned :)

Ok for this one.


>> +}
>> +
>> +static u32 at91_shdwc_debouncer_value(struct platform_device *pdev,
>> +				      u32 in_period_us)
>> +{
>> +	int i;
>> +	int max_idx = ARRAY_SIZE(sdwc_dbc_period) - 1;
>> +	unsigned long long period_us;
>> +	unsigned long long max_period_us = DBC_PERIOD_US(sdwc_dbc_period[max_idx]);
>> +
>> +	if (in_period_us > max_period_us) {
>> +		dev_warn(&pdev->dev,
>> +			 "debouncer period %u too big, reduced to %llu us\n",
>> +			 in_period_us, max_period_us);
>> +		return max_idx;
>> +	}
>> +
>> +	for (i = max_idx - 1; i > 0; i--) {
>> +		period_us = DBC_PERIOD_US(sdwc_dbc_period[i]);
>> +		dev_dbg(&pdev->dev, "%s: ref[%d] = %llu\n",
>> +						__func__, i, period_us);
> 
> Alignment is not correct.
> 
>> +		if (in_period_us > period_us)
>> +			break;
>> +	}
>> +
>> +	return i + 1;
>> +}
>> +
>> +static u32 at91_shdwc_get_wakeup_input(struct platform_device *pdev,
>> +				       struct device_node *np)
>> +{
>> +	struct device_node *cnp;
>> +	u32 wk_input_mask;
>> +	u32 wuir = 0;
>> +	u32 wk_input;
>> +
>> +	for_each_child_of_node(np, cnp) {
>> +		if (of_property_read_u32(cnp, "reg", &wk_input)) {
>> +			dev_warn(&pdev->dev, "reg property is missing for %s\n",
>> +				 cnp->full_name);
>> +			continue;
>> +		}
>> +
>> +		wk_input_mask = 1 << wk_input;
>> +		if (!(wk_input_mask & AT91_SHDW_WKUPEN_MASK)) {
>> +			dev_warn(&pdev->dev,
>> +				 "wake-up input %d out of bounds ignore\n",
>> +				 wk_input);
>> +			continue;
>> +		}
>> +		wuir |= wk_input_mask;
>> +
>> +		if (of_property_read_bool(cnp, "atmel,wakeup-active-high"))
>> +			wuir |= AT91_SHDW_WKUPT(wk_input);
>> +
>> +		dev_dbg(&pdev->dev, "%s: (child %d) wuir = %#x\n",
>> +						__func__, wk_input, wuir);
> 
> Alignment is not correct

I don't agree with you on the 2 last ones. In Documentation/CodingStyle,
it is said that:

"Chapter 2: Breaking long lines and strings
[..]
Descendants are always substantially shorter than the parent and
are placed substantially to the right."

Together with the 80 column requirement that I also fulfil, I think that
my code is well aligned.

So I keep it like this ;-)

Bye,
-- 
Nicolas Ferre



More information about the linux-arm-kernel mailing list