[PATCH v12] [PATCH] PCI: Xilinx-NWL-PCIe: Adding support for Xilinx NWL PCIe Host Controller

[Bharat Kumar Gogada]

Hi Bjorn,
 
> I forgot I still have one question here:
> 
> On Sun, Mar 06, 2016 at 10:02:14PM +0530, Bharat Kumar Gogada wrote:
> > Adding PCIe Root Port driver for Xilinx PCIe NWL bridge IP.
> 
> > +static bool nwl_pcie_valid_device(struct pci_bus *bus, unsigned int
> > +devfn) {
> > +	struct nwl_pcie *pcie = bus->sysdata;
> > +
> > +	/* Check link,before accessing downstream ports */
> > +	if (bus->number != pcie->root_busno) {
> > +		if (!nwl_pcie_link_up(pcie))
> > +			return false;
> > +	}
> 
> This seems racy.  What if we check, and the link is up, but the link goes down
> before we actually complete the config access?
> 
> I'm suggesting that this check for the link being up might be superfluous.
Without the above check and also if there is no EP then we are getting kernel stack as follows,
[    2.654105] PCI host bridge /amba/pcie at fd0e0000 ranges:
[    2.659268]   No bus range found for /amba/pcie at fd0e0000, using [bus 00-ff]
[    2.666195]   MEM 0xe1000000..0xefffffff -> 0xe1000000
[    2.671410] nwl-pcie fd0e0000.pcie: PCI host bridge to bus 0000:00
[    2.677436] pci_bus 0000:00: root bus resource [bus 00-ff]
[    2.682883] pci_bus 0000:00: root bus resource [mem 0xe1000000-0xefffffff]
[    2.690031] Unhandled fault: synchronous external abort (0x96000210) at 0xffffff8000200000
[    2.690036] nwl-pcie fd0e0000.pcie: Slave error
[    2.702582] Internal error: : 96000210 [#1] SMP
[    2.707078] Modules linked in:
[    2.710108] CPU: 3 PID: 1 Comm: swapper/0 Not tainted 4.5.0-rc6+ #5
[    2.716332] Hardware name: ZynqMP (DT)
[    2.720659] task: ffffffc0798bed00 ti: ffffffc0798c0000 task.ti: ffffffc0798c0000
[    2.728102] PC is at pci_generic_config_read+0x38/0x9c
[    2.733202] LR is at pci_generic_config_read+0x1c/0x9c
.......
[    3.322701] [<ffffffc000498b1c>] pci_generic_config_read+0x38/0x9c
[    3.328842] [<ffffffc000498f54>] pci_bus_read_config_dword+0x80/0xb0
[    3.335156] [<ffffffc00049abd4>] pci_bus_read_dev_vendor_id+0x30/0x104
[    3.341643] [<ffffffc00049c5b0>] pci_scan_single_device+0x50/0xc4
[    3.347698] [<ffffffc00049c674>] pci_scan_slot+0x50/0xe8
[    3.352974] [<ffffffc00049d530>] pci_scan_child_bus+0x30/0xd8
[    3.358683] [<ffffffc00049d210>] pci_scan_bridge+0x1fc/0x4ec
[    3.364306] [<ffffffc00049d58c>] pci_scan_child_bus+0x8c/0xd8
[    3.370016] [<ffffffc0004b2d9c>] nwl_pcie_probe+0x6c4/0x8e0
.....

> The hardware should do something reasonable with the config access if it
> can't send it down the link.
When Link is down and H/W gets a ECAM access request for downstream ports, hardware responds by DECERR (decode error) status on AXI Interface.

So without any EP and without this condition, Linux kernel cannot determine above response from H/W. So the above condition is useful only when no EP is connected.

Now even if the link is up initially, but the link goes down before we actually complete the config access, then H/W responds by DECERR, then Linux kernel might throw similar stack. (We haven't observed this condition yet)

It looks like we need a different type of hardware response to get rid of this situation, but it's not easy way. 
Have you come across this/similar kind of problem anywhere else? 
Can you suggest if there is any other way to handle this.

Thanks
Bharat