[PATCH v3 3/9] irqchip/gic-v2: Gather ACPI specific data in a single structure

Christoffer Dall christoffer.dall at linaro.org
Tue Mar 8 21:47:10 PST 2016


On Tue, Mar 08, 2016 at 11:29:27AM +0000, Julien Grall wrote:
> For now, there is only one member. More member will be added later.

questionable commit message

> 
> Signed-off-by: Julien Grall <julien.grall at arm.com>
> 
> ---
> Cc: Thomas Gleixner <tglx at linutronix.de>
> Cc: Jason Cooper <jason at lakedaemon.net>
> Cc: Marc Zyngier <marc.zyngier at arm.com>
> 
>     Changes in v2:
>         - Patch added
> ---
>  drivers/irqchip/irq-gic.c | 11 +++++++----
>  1 file changed, 7 insertions(+), 4 deletions(-)
> 
> diff --git a/drivers/irqchip/irq-gic.c b/drivers/irqchip/irq-gic.c
> index 8f9ebf7..fbde202 100644
> --- a/drivers/irqchip/irq-gic.c
> +++ b/drivers/irqchip/irq-gic.c
> @@ -1245,7 +1245,10 @@ IRQCHIP_DECLARE(pl390, "arm,pl390", gic_of_init);
>  #endif
>  
>  #ifdef CONFIG_ACPI
> -static phys_addr_t cpu_phy_base __initdata;
> +static struct
> +{
> +	phys_addr_t cpu_phy_base;
> +} acpi_data __initdata;
>  
>  static int __init
>  gic_acpi_parse_madt_cpu(struct acpi_subtable_header *header,
> @@ -1265,10 +1268,10 @@ gic_acpi_parse_madt_cpu(struct acpi_subtable_header *header,
>  	 * All CPU interface addresses have to be the same.
>  	 */
>  	gic_cpu_base = processor->base_address;
> -	if (cpu_base_assigned && gic_cpu_base != cpu_phy_base)
> +	if (cpu_base_assigned && gic_cpu_base != acpi_data.cpu_phy_base)
>  		return -EINVAL;
>  
> -	cpu_phy_base = gic_cpu_base;
> +	acpi_data.cpu_phy_base = gic_cpu_base;
>  	cpu_base_assigned = 1;
>  	return 0;
>  }
> @@ -1316,7 +1319,7 @@ static int __init gic_v2_acpi_init(struct acpi_subtable_header *header,
>  		return -EINVAL;
>  	}
>  
> -	cpu_base = ioremap(cpu_phy_base, ACPI_GIC_CPU_IF_MEM_SIZE);
> +	cpu_base = ioremap(acpi_data.cpu_phy_base, ACPI_GIC_CPU_IF_MEM_SIZE);
>  	if (!cpu_base) {
>  		pr_err("Unable to map GICC registers\n");
>  		return -ENOMEM;
> -- 
> 1.9.1
> 
super nit: I would use cpu_phys_base instead of cpu_phy_base, but I'll
leave it up to you.

Acked-by: Christoffer Dall <christoffer.dall at linaro.org>



More information about the linux-arm-kernel mailing list