[Patch v2] ARM: dts: vf610-zii-dev: Add ZII development board.
Andrew Lunn
andrew at lunn.ch
Mon Mar 7 06:34:08 PST 2016
On Thu, Feb 25, 2016 at 06:44:44PM +0100, Andrew Lunn wrote:
> From: Cory Tusar <cory.tusar at pid1solutions.com>
>
> This commit adds support for Rev. B of a Zodiac Inflight Innovations
> development board, mainly intended for DSA and ARINC 429 development
> work.
Shawn, Stefan, any comments on this version of the patch?
Thanks
Andrew
>
> Signed-off-by: Cory Tusar <cory.tusar at pid1solutions.com>
> Signed-off-by: Andrew Lunn <andrew at lunn.ch>
> ---
> v2
> Add ZII Copyright
> Dual license
> Remove bootargs and extend stdout-path
> Remove address format from regulator nodes
> Remove extraneous space i2c_3 node
> Move iomuxc to end
> Remove L2 node
> Add missing gpio-controller to gpio6
> Removed unused fixed clocks
> Add an spi node
> Fix memory range
> Fix naming of GPIO i2c expanders
> Disable DMA on serial port, which appears to cause corrupt.
>
> Documentation/devicetree/bindings/net/mdio-mux.txt says:
>
> Required properties for child nodes:
> - #address-cells = <1>;
> - #size-cells = <0>;
> - reg : The sub-bus number.
>
> So i ignored the request to remove these properties.
> ---
> arch/arm/boot/dts/Makefile | 3 +-
> arch/arm/boot/dts/vf610-zii-dev-rev-b.dts | 735 ++++++++++++++++++++++++++++++
> 2 files changed, 737 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/boot/dts/vf610-zii-dev-rev-b.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index a4a6d70e8b26..47c4c2ff41de 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -372,7 +372,8 @@ dtb-$(CONFIG_SOC_VF610) += \
> vf610m4-colibri.dtb \
> vf610-cosmic.dtb \
> vf610m4-cosmic.dtb \
> - vf610-twr.dtb
> + vf610-twr.dtb \
> + vf610-zii-dev-rev-b.dtb
> dtb-$(CONFIG_ARCH_MXS) += \
> imx23-evk.dtb \
> imx23-olinuxino.dtb \
> diff --git a/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts b/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts
> new file mode 100644
> index 000000000000..c2fb60b9b36c
> --- /dev/null
> +++ b/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts
> @@ -0,0 +1,735 @@
> +/*
> + * Copyright (C) 2015, 2016 Zodiac Inflight Innovations
> + *
> + * Based on an original 'vf610-twr.dts' which is Copyright 2015,
> + * Freescale Semiconductor, Inc.
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This file is distributed in the hope that it will be useful
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "vf610.dtsi"
> +
> +/ {
> + model = "ZII VF610 Development Board, Rev B";
> + compatible = "zii,vf610dev-b", "zii,vf610dev", "fsl,vf610";
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + memory {
> + reg = <0x80000000 0x20000000>;
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> + pinctrl-0 = <&pinctrl_leds_debug>;
> + pinctrl-names = "default";
> +
> + debug_1 {
> + label = "zii:green:debug1";
> + gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + mdio-mux {
> + compatible = "mdio-mux-gpio";
> + pinctrl-0 = <&pinctrl_mdio_mux>;
> + pinctrl-names = "default";
> + gpios = <&gpio0 8 GPIO_ACTIVE_HIGH
> + &gpio0 9 GPIO_ACTIVE_HIGH
> + &gpio0 24 GPIO_ACTIVE_HIGH
> + &gpio0 25 GPIO_ACTIVE_HIGH>;
> + mdio-parent-bus = <&mdio1>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + mdio_mux_1: mdio at 1 {
> + reg = <1>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + mdio_mux_2: mdio at 2 {
> + reg = <2>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + mdio_mux_4: mdio at 4 {
> + reg = <4>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + mdio_mux_8: mdio at 8 {
> + reg = <8>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> + };
> +
> + dsa at 0 {
> + compatible = "marvell,dsa";
> + #address-cells = <2>;
> + #size-cells = <0>;
> +
> + dsa,ethernet = <&fec1>;
> + dsa,mii-bus = <&mdio_mux_1>;
> +
> + /* 6352 - Primary - 7 ports */
> + switch0: switch at 2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x00 0>;
> + eeprom-length = <512>;
> +
> + port at 0 {
> + reg = <0>;
> + label = "lan0";
> + };
> +
> + port at 1 {
> + reg = <1>;
> + label = "lan1";
> + };
> +
> + port at 2 {
> + reg = <2>;
> + label = "lan2";
> + };
> +
> + switch0port5: port at 5 {
> + reg = <5>;
> + label = "dsa";
> + phy-mode = "rgmii-txid";
> + link = <&switch1port6
> + &switch2port9>;
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + port at 6 {
> + reg = <6>;
> + label = "cpu";
> + fixed-link {
> + speed = <100>;
> + full-duplex;
> + };
> + };
> +
> + };
> +
> + /* 6352 - Secondary - 7 ports */
> + switch1: switch at 0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x00 1>;
> + eeprom-length = <512>;
> + mii-bus = <&mdio_mux_2>;
> +
> + port at 0 {
> + reg = <0>;
> + label = "lan3";
> + };
> +
> + port at 1 {
> + reg = <1>;
> + label = "lan4";
> + };
> +
> + port at 2 {
> + reg = <2>;
> + label = "lan5";
> + };
> +
> + switch1port5: port at 5 {
> + reg = <5>;
> + label = "dsa";
> + link = <&switch2port9>;
> + phy-mode = "rgmii-txid";
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + switch1port6: port at 6 {
> + reg = <6>;
> + label = "dsa";
> + phy-mode = "rgmii-txid";
> + link = <&switch0port5>;
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> + };
> +
> + /* 6185 - 10 ports */
> + switch2: switch at 6 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x00 2>;
> + mii-bus = <&mdio_mux_4>;
> +
> + port at 0 {
> + reg = <0>;
> + label = "lan6";
> + };
> +
> + port at 1 {
> + reg = <1>;
> + label = "lan7";
> + };
> +
> + port at 2 {
> + reg = <2>;
> + label = "lan8";
> + };
> +
> + port at 3 {
> + reg = <3>;
> + label = "optical3";
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + link-gpios = <&gpio6 2
> + GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + port at 4 {
> + reg = <4>;
> + label = "optical4";
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + link-gpios = <&gpio6 3
> + GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + switch2port9: port at 9 {
> + reg = <9>;
> + label = "dsa";
> + phy-mode = "rgmii-txid";
> + link = <&switch1port5
> + &switch0port5>;
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> + };
> + };
> +
> + reg_vcc_3v3_mcu: reg_vcc_3v3_mcu {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_3v3_mcu";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + usb0_vbus: usb0_vbus {
> + compatible = "regulator-fixed";
> + pinctrl-0 = <&pinctrl_usb_vbus>;
> + regulator-name = "usb_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + gpio = <&gpio0 6 0>;
> + };
> +
> + spi0 {
> + compatible = "spi-gpio";
> + pinctrl-0 = <&pinctrl_gpio_spi0>;
> + pinctrl-names = "default";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + gpio-sck = <&gpio1 12 GPIO_ACTIVE_HIGH>;
> + gpio-mosi = <&gpio1 11 GPIO_ACTIVE_HIGH>;
> + gpio-miso = <&gpio1 10 GPIO_ACTIVE_HIGH>;
> + cs-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH
> + &gpio1 8 GPIO_ACTIVE_HIGH>;
> + num-chipselects = <2>;
> +
> + m25p128 at 0 {
> + compatible = "m25p128", "jedec,spi-nor";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <0>;
> + spi-max-frequency = <1000000>;
> + };
> +
> + at93c46d at 1 {
> + compatible = "atmel,at93c46d";
> + pinctrl-0 = <&pinctrl_gpio_e6185_eeprom_sel>;
> + pinctrl-names = "default";
> + #address-cells = <0>;
> + #size-cells = <0>;
> + reg = <1>;
> + spi-max-frequency = <500000>;
> + spi-cs-high;
> + data-size = <16>;
> + select-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +};
> +
> +&fec0 {
> + phy-mode = "rmii";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec0>;
> + status = "okay";
> +};
> +
> +&fec1 {
> + phy-mode = "rmii";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec1>;
> + status = "okay";
> +
> + fixed-link {
> + speed = <100>;
> + full-duplex;
> + };
> +
> + mdio1: mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";
> + };
> +};
> +
> +&adc0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_adc0_ad5>;
> + vref-supply = <®_vcc_3v3_mcu>;
> + status = "okay";
> +};
> +
> +&edma0 {
> + status = "okay";
> +};
> +
> +&esdhc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_esdhc1>;
> + bus-width = <4>;
> + status = "okay";
> +};
> +
> +&i2c0 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c0>;
> + status = "okay";
> +
> + gpio5: pca9554 at 20 {
> + compatible = "nxp,pca9554";
> + reg = <0x20>;
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + };
> +
> + gpio6: pca9554 at 22 {
> + compatible = "nxp,pca9554";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pca9554_22>;
> + reg = <0x22>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-parent = <&gpio2>;
> + interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + lm75 at 48 {
> + compatible = "national,lm75";
> + reg = <0x48>;
> + };
> +
> + at24c04 at 50 {
> + compatible = "atmel,24c04";
> + reg = <0x50>;
> + };
> +
> + at24c04 at 52 {
> + compatible = "atmel,24c04";
> + reg = <0x52>;
> + };
> +
> + ds1682 at 6b {
> + compatible = "dallas,ds1682";
> + reg = <0x6b>;
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +};
> +
> +&i2c2 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + status = "okay";
> +
> + tca9548 at 70 {
> + compatible = "nxp,pca9548";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x70>;
> + reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
> +
> + i2c2_0: i2c at 0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + sfp1: at24c04 at 50 {
> + compatible = "atmel,24c02";
> + reg = <0x50>;
> + };
> + };
> +
> + i2c2_1: i2c at 1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> +
> + sfp2: at24c04 at 50 {
> + compatible = "atmel,24c02";
> + reg = <0x50>;
> + };
> + };
> +
> + i2c2_2: i2c at 2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <2>;
> +
> + sfp3: at24c04 at 50 {
> + compatible = "atmel,24c02";
> + reg = <0x50>;
> + };
> + };
> +
> + i2c2_3: i2c at 3 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <3>;
> +
> + sfp4: at24c04 at 50 {
> + compatible = "atmel,24c02";
> + reg = <0x50>;
> + };
> +
> + };
> +
> + i2c2_4: i2c at 4 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <4>;
> + };
> + };
> +};
> +
> +&i2c3 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c3>;
> + status = "okay";
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart0>;
> + status = "okay";
> + dmas = <>;
> + dma-names = "";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + status = "okay";
> +};
> +
> +&usbdev0 {
> + disable-over-current;
> + status = "okay";
> + vbus-supply = <&usb0_vbus>;
> + dr_mode = "host";
> +};
> +
> +&usbh1 {
> + disable-over-current;
> + status = "okay";
> +};
> +
> +&usbmisc0 {
> + status = "okay";
> +};
> +
> +&usbmisc1 {
> + status = "okay";
> +};
> +
> +&usbphy0 {
> + status = "okay";
> +};
> +
> +&usbphy1 {
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c_mux_reset>;
> +
> + vf610-zii {
> + pinctrl_usb_vbus: pinctrl-usb-vbus {
> + fsl,pins = <
> + VF610_PAD_PTA16__GPIO_6 0x31c2
> + >;
> + };
> +
> + pinctrl_i2c_mux_reset: pinctrl-i2c-mux-reset {
> + fsl,pins = <
> + VF610_PAD_PTE14__GPIO_119 0x31c2
> + >;
> + };
> +
> + pinctrl_adc0_ad5: adc0ad5grp {
> + fsl,pins = <
> + VF610_PAD_PTC30__ADC0_SE5 0x00a1
> + >;
> + };
> +
> + pinctrl_dspi0: dspi0grp {
> + fsl,pins = <
> + VF610_PAD_PTB18__DSPI0_CS1 0x1182
> + VF610_PAD_PTB19__DSPI0_CS0 0x1182
> + VF610_PAD_PTB20__DSPI0_SIN 0x1181
> + VF610_PAD_PTB21__DSPI0_SOUT 0x1182
> + VF610_PAD_PTB22__DSPI0_SCK 0x1182
> + >;
> + };
> +
> + pinctrl_dspi2: dspi2grp {
> + fsl,pins = <
> + VF610_PAD_PTD31__DSPI2_CS1 0x1182
> + VF610_PAD_PTD30__DSPI2_CS0 0x1182
> + VF610_PAD_PTD29__DSPI2_SIN 0x1181
> + VF610_PAD_PTD28__DSPI2_SOUT 0x1182
> + VF610_PAD_PTD27__DSPI2_SCK 0x1182
> + >;
> + };
> +
> + pinctrl_esdhc1: esdhc1grp {
> + fsl,pins = <
> + VF610_PAD_PTA24__ESDHC1_CLK 0x31ef
> + VF610_PAD_PTA25__ESDHC1_CMD 0x31ef
> + VF610_PAD_PTA26__ESDHC1_DAT0 0x31ef
> + VF610_PAD_PTA27__ESDHC1_DAT1 0x31ef
> + VF610_PAD_PTA28__ESDHC1_DATA2 0x31ef
> + VF610_PAD_PTA29__ESDHC1_DAT3 0x31ef
> + VF610_PAD_PTA7__GPIO_134 0x219d
> + >;
> + };
> +
> + pinctrl_fec1: fec1grp {
> + fsl,pins = <
> + VF610_PAD_PTA6__RMII_CLKIN 0x30d1
> + VF610_PAD_PTC9__ENET_RMII1_MDC 0x30d2
> + VF610_PAD_PTC10__ENET_RMII1_MDIO 0x30d3
> + VF610_PAD_PTC11__ENET_RMII1_CRS 0x30d1
> + VF610_PAD_PTC12__ENET_RMII1_RXD1 0x30d1
> + VF610_PAD_PTC13__ENET_RMII1_RXD0 0x30d1
> + VF610_PAD_PTC14__ENET_RMII1_RXER 0x30d1
> + VF610_PAD_PTC15__ENET_RMII1_TXD1 0x30d2
> + VF610_PAD_PTC16__ENET_RMII1_TXD0 0x30d2
> + VF610_PAD_PTC17__ENET_RMII1_TXEN 0x30d2
> + >;
> + };
> +
> + pinctrl_i2c0: i2c0grp {
> + fsl,pins = <
> + VF610_PAD_PTB14__I2C0_SCL 0x37ff
> + VF610_PAD_PTB15__I2C0_SDA 0x37ff
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + VF610_PAD_PTB16__I2C1_SCL 0x37ff
> + VF610_PAD_PTB17__I2C1_SDA 0x37ff
> + >;
> + };
> +
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + VF610_PAD_PTA22__I2C2_SCL 0x37ff
> + VF610_PAD_PTA23__I2C2_SDA 0x37ff
> + >;
> + };
> +
> + pinctrl_i2c3: i2c3grp {
> + fsl,pins = <
> + VF610_PAD_PTA30__I2C3_SCL 0x37ff
> + VF610_PAD_PTA31__I2C3_SDA 0x37ff
> + >;
> + };
> +
> + pinctrl_pwm0: pwm0grp {
> + fsl,pins = <
> + VF610_PAD_PTB0__FTM0_CH0 0x1582
> + VF610_PAD_PTB1__FTM0_CH1 0x1582
> + VF610_PAD_PTB2__FTM0_CH2 0x1582
> + VF610_PAD_PTB3__FTM0_CH3 0x1582
> + >;
> + };
> +
> + pinctrl_uart0: uart0grp {
> + fsl,pins = <
> + VF610_PAD_PTB10__UART0_TX 0x21a2
> + VF610_PAD_PTB11__UART0_RX 0x21a1
> + >;
> + };
> +
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + VF610_PAD_PTB23__UART1_TX 0x21a2
> + VF610_PAD_PTB24__UART1_RX 0x21a1
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + VF610_PAD_PTD0__UART2_TX 0x21a2
> + VF610_PAD_PTD1__UART2_RX 0x21a1
> + >;
> + };
> +
> + pinctrl_qspi0: qspi0grp {
> + fsl,pins = <
> + VF610_PAD_PTD7__QSPI0_B_QSCK 0x31c3
> + VF610_PAD_PTD8__QSPI0_B_CS0 0x31ff
> + VF610_PAD_PTD9__QSPI0_B_DATA3 0x31c3
> + VF610_PAD_PTD10__QSPI0_B_DATA2 0x31c3
> + VF610_PAD_PTD11__QSPI0_B_DATA1 0x31c3
> + VF610_PAD_PTD12__QSPI0_B_DATA0 0x31c3
> + >;
> + };
> +
> + pinctrl_usb0_host: usb0-host-grp {
> + fsl,pins = <
> + VF610_PAD_PTD6__GPIO_85 0x0062
> + >;
> + };
> +
> + pinctrl_mdio_mux: pinctrl-mdio-mux {
> + fsl,pins = <
> + VF610_PAD_PTA18__GPIO_8 0x31c2
> + VF610_PAD_PTA19__GPIO_9 0x31c2
> + VF610_PAD_PTB2__GPIO_24 0x31c2
> + VF610_PAD_PTB3__GPIO_25 0x31c2
> + >;
> + };
> +
> + pinctrl_gpio_e6185_eeprom_sel: pinctrl-gpio-e6185-eeprom-spi0 {
> + fsl,pins = <
> + VF610_PAD_PTE27__GPIO_132 0x33e2
> + >;
> + };
> +
> + pinctrl_gpio_spi0: pinctrl-gpio-spi0 {
> + fsl,pins = <
> + VF610_PAD_PTB22__GPIO_44 0x33e2
> + VF610_PAD_PTB21__GPIO_43 0x33e2
> + VF610_PAD_PTB20__GPIO_42 0x33e1
> + VF610_PAD_PTB19__GPIO_41 0x33e2
> + VF610_PAD_PTB18__GPIO_40 0x33e2
> + >;
> + };
> +
> + pinctrl_fec0: fec0grp {
> + fsl,pins = <
> + VF610_PAD_PTC0__ENET_RMII0_MDC 0x30d2
> + VF610_PAD_PTC1__ENET_RMII0_MDIO 0x30d3
> + VF610_PAD_PTC2__ENET_RMII0_CRS 0x30d1
> + VF610_PAD_PTC3__ENET_RMII0_RXD1 0x30d1
> + VF610_PAD_PTC4__ENET_RMII0_RXD0 0x30d1
> + VF610_PAD_PTC5__ENET_RMII0_RXER 0x30d1
> + VF610_PAD_PTC6__ENET_RMII0_TXD1 0x30d2
> + VF610_PAD_PTC7__ENET_RMII0_TXD0 0x30d2
> + VF610_PAD_PTC8__ENET_RMII0_TXEN 0x30d2
> + >;
> + };
> +
> + pinctrl_leds_debug: pinctrl-leds-debug {
> + fsl,pins = <
> + VF610_PAD_PTD20__GPIO_74 0x31c2
> + >;
> + };
> +
> + pinctrl_pca9554_22: pinctrl-pca95540-22 {
> + fsl,pins = <
> + VF610_PAD_PTB28__GPIO_98 0x219d
> + >;
> + };
> + };
> +};
> +
> --
> 2.7.0
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
More information about the linux-arm-kernel
mailing list