[PATCH 2/2] clk: hi6220: initialize UART1 clock to 150MHz

[Guodong Xu]

On 28 June 2016 at 19:56, Jorge Ramirez <jorge.ramirez-ortiz at linaro.org> wrote:
> On 06/28/2016 12:31 PM, Guodong Xu wrote:
>>
>> From: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz at linaro.org>
>>
>> Early at boot, during the sys_clk initialization, make sure UART1 uses
>> the higher frequency clock.
>>
>> This enables support for higher baud rates (up to 3Mbps) required to
>> support faster bluetooth transfers.
>>
>> Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz at linaro.org>
>> Signed-off-by: Guodong Xu <guodong.xu at linaro.org>
>> ---
>>   drivers/clk/hisilicon/clk-hi6220.c | 12 ++++++++++--
>>   1 file changed, 10 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/clk/hisilicon/clk-hi6220.c
>> b/drivers/clk/hisilicon/clk-hi6220.c
>> index a36ffcb..55bd9bb 100644
>> --- a/drivers/clk/hisilicon/clk-hi6220.c
>> +++ b/drivers/clk/hisilicon/clk-hi6220.c
>> @@ -11,6 +11,7 @@
>>    */
>>     #include <linux/kernel.h>
>> +#include <linux/clk.h>
>>   #include <linux/clk-provider.h>
>>   #include <linux/clkdev.h>
>>   #include <linux/io.h>
>> @@ -70,10 +71,10 @@ static struct hisi_gate_clock
>> hi6220_separated_gate_clks_ao[] __initdata = {
>>         { HI6220_UART0_PCLK,  "uart0_pclk",  "clk_tcxo",
>> CLK_SET_RATE_PARENT|CLK_IGNORE_UNUSED, 0x630, 24, 0, },
>>   };
>>   +static struct hisi_clock_data *clk_data_ao;
>> +
>>   static void __init hi6220_clk_ao_init(struct device_node *np)
>>   {
>> -       struct hisi_clock_data *clk_data_ao;
>> -
>>         clk_data_ao = hisi_clk_init(np, HI6220_AO_NR_CLKS);
>>         if (!clk_data_ao)
>>                 return;
>> @@ -192,6 +193,13 @@ static void __init hi6220_clk_sys_init(struct
>> device_node *np)
>>         hi6220_clk_register_divider(hi6220_div_clks_sys,
>>                         ARRAY_SIZE(hi6220_div_clks_sys), clk_data);
>> +
>> +       if (!clk_data_ao)
>> +               return;
>> +
>> +       /* enable high speed clock on UART1 mux */
>> +       clk_set_parent(clk_data->clk_data.clks[HI6220_UART1_SRC],
>> +                       clk_data_ao->clk_data.clks[HI6220_150M]);
>>   }
>>   CLK_OF_DECLARE(hi6220_clk_sys, "hisilicon,hi6220-sysctrl",
>> hi6220_clk_sys_init);
>>
>
>
> please bear with me on this. it does need rework.
>

V2 was sent. Thanks Jorge.

-Guodong

>