[PATCH v4 2/5] mfd: add Ricoh RN5T567 PMIC support
Stefan Agner
stefan at agner.ch
Mon Jun 27 23:27:54 PDT 2016
The Ricoh RN5T567 is from the same family as the Ricoh RN5T618 is,
the differences are:
+ DCDC4
+ Slightly different output voltage/currents
+ 32kHz Output
- ADC/Charger capabilities
Signed-off-by: Stefan Agner <stefan at agner.ch>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler at toradex.com>
Acked-by: Rob Herring <robh at kernel.org>
---
Documentation/devicetree/bindings/mfd/rn5t618.txt | 19 +++++++++--------
drivers/mfd/Kconfig | 7 ++++---
drivers/mfd/rn5t618.c | 25 ++++++++++++++++-------
include/linux/mfd/rn5t618.h | 12 +++++++++++
4 files changed, 45 insertions(+), 18 deletions(-)
diff --git a/Documentation/devicetree/bindings/mfd/rn5t618.txt b/Documentation/devicetree/bindings/mfd/rn5t618.txt
index 937785a..9e6770b 100644
--- a/Documentation/devicetree/bindings/mfd/rn5t618.txt
+++ b/Documentation/devicetree/bindings/mfd/rn5t618.txt
@@ -1,18 +1,21 @@
-* Ricoh RN5T618 PMIC
+* Ricoh RN5T567/RN5T618 PMIC
-Ricoh RN5T618 is a power management IC which integrates 3 step-down
-DCDC converters, 7 low-dropout regulators, a Li-ion battery charger,
-fuel gauge, ADC, GPIOs and a watchdog timer. It can be controlled
-through a I2C interface.
+Ricoh RN5T567/RN5T618 is a power management IC family which integrates
+3 to 4 step-down DCDC converters, 7 low-dropout regulators, GPIOs and
+a watchdog timer. The RN5T618 provides additionally a Li-ion battery
+charger, fuel gauge and an ADC. It can be controlled through an I2C
+interface.
Required properties:
- - compatible: should be "ricoh,rn5t618"
+ - compatible: must be one of
+ "ricoh,rn5t567"
+ "ricoh,rn5t618"
- reg: the I2C slave address of the device
Sub-nodes:
- regulators: the node is required if the regulator functionality is
- needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, LDO1,
- LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2.
+ needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, DCDC4
+ (RN5T567), LDO1, LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2.
The common bindings for each individual regulator can be found in:
Documentation/devicetree/bindings/regulator/regulator.txt
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 1bcf601..ff031a7 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -852,13 +852,14 @@ config MFD_RK808
including interrupts, RTC, LDO & DCDC regulators, and onkey.
config MFD_RN5T618
- tristate "Ricoh RN5T5618 PMIC"
+ tristate "Ricoh RN5T567/618 PMIC"
depends on I2C
+ depends on OF
select MFD_CORE
select REGMAP_I2C
help
- Say yes here to add support for the Ricoh RN5T618 PMIC. This
- driver provides common support for accessing the device,
+ Say yes here to add support for the Ricoh RN5T567 or R5T618 PMIC.
+ This driver provides common support for accessing the device,
additional drivers must be enabled in order to use the
functionality of the device.
diff --git a/drivers/mfd/rn5t618.c b/drivers/mfd/rn5t618.c
index 0ad51d7..c86160d 100644
--- a/drivers/mfd/rn5t618.c
+++ b/drivers/mfd/rn5t618.c
@@ -2,6 +2,7 @@
* MFD core driver for Ricoh RN5T618 PMIC
*
* Copyright (C) 2014 Beniamino Galvani <b.galvani at gmail.com>
+ * Copyright (C) 2016 Toradex AG
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
@@ -15,6 +16,7 @@
#include <linux/mfd/core.h>
#include <linux/mfd/rn5t618.h>
#include <linux/module.h>
+#include <linux/of_device.h>
#include <linux/regmap.h>
static const struct mfd_cell rn5t618_cells[] = {
@@ -59,17 +61,32 @@ static void rn5t618_power_off(void)
RN5T618_SLPCNT_SWPWROFF, RN5T618_SLPCNT_SWPWROFF);
}
+static const struct of_device_id rn5t618_of_match[] = {
+ { .compatible = "ricoh,rn5t567", .data = (void *)RN5T567 },
+ { .compatible = "ricoh,rn5t618", .data = (void *)RN5T618 },
+ { }
+};
+MODULE_DEVICE_TABLE(of, rn5t618_of_match);
+
static int rn5t618_i2c_probe(struct i2c_client *i2c,
const struct i2c_device_id *id)
{
+ const struct of_device_id *of_id;
struct rn5t618 *priv;
int ret;
+ of_id = of_match_device(rn5t618_of_match, &i2c->dev);
+ if (!of_id) {
+ dev_err(&i2c->dev, "Failed to find matching DT ID\n");
+ return -EINVAL;
+ }
+
priv = devm_kzalloc(&i2c->dev, sizeof(*priv), GFP_KERNEL);
if (!priv)
return -ENOMEM;
i2c_set_clientdata(i2c, priv);
+ priv->variant = (long)of_id->data;
priv->regmap = devm_regmap_init_i2c(i2c, &rn5t618_regmap_config);
if (IS_ERR(priv->regmap)) {
@@ -105,12 +122,6 @@ static int rn5t618_i2c_remove(struct i2c_client *i2c)
return 0;
}
-static const struct of_device_id rn5t618_of_match[] = {
- { .compatible = "ricoh,rn5t618" },
- { }
-};
-MODULE_DEVICE_TABLE(of, rn5t618_of_match);
-
static const struct i2c_device_id rn5t618_i2c_id[] = {
{ }
};
@@ -129,5 +140,5 @@ static struct i2c_driver rn5t618_i2c_driver = {
module_i2c_driver(rn5t618_i2c_driver);
MODULE_AUTHOR("Beniamino Galvani <b.galvani at gmail.com>");
-MODULE_DESCRIPTION("Ricoh RN5T618 MFD driver");
+MODULE_DESCRIPTION("Ricoh RN5T567/618 MFD driver");
MODULE_LICENSE("GPL v2");
diff --git a/include/linux/mfd/rn5t618.h b/include/linux/mfd/rn5t618.h
index c72d534..54179c2 100644
--- a/include/linux/mfd/rn5t618.h
+++ b/include/linux/mfd/rn5t618.h
@@ -20,6 +20,7 @@
#define RN5T618_OTPVER 0x01
#define RN5T618_IODAC 0x02
#define RN5T618_VINDAC 0x03
+#define RN5T618_OUT32KEN 0x05
#define RN5T618_CPUCNT 0x06
#define RN5T618_PSWR 0x07
#define RN5T618_PONHIS 0x09
@@ -38,6 +39,7 @@
#define RN5T618_DC1_SLOT 0x16
#define RN5T618_DC2_SLOT 0x17
#define RN5T618_DC3_SLOT 0x18
+#define RN5T618_DC4_SLOT 0x19
#define RN5T618_LDO1_SLOT 0x1b
#define RN5T618_LDO2_SLOT 0x1c
#define RN5T618_LDO3_SLOT 0x1d
@@ -54,12 +56,16 @@
#define RN5T618_DC2CTL2 0x2f
#define RN5T618_DC3CTL 0x30
#define RN5T618_DC3CTL2 0x31
+#define RN5T618_DC4CTL 0x32
+#define RN5T618_DC4CTL2 0x33
#define RN5T618_DC1DAC 0x36
#define RN5T618_DC2DAC 0x37
#define RN5T618_DC3DAC 0x38
+#define RN5T618_DC4DAC 0x39
#define RN5T618_DC1DAC_SLP 0x3b
#define RN5T618_DC2DAC_SLP 0x3c
#define RN5T618_DC3DAC_SLP 0x3d
+#define RN5T618_DC4DAC_SLP 0x3e
#define RN5T618_DCIREN 0x40
#define RN5T618_DCIRQ 0x41
#define RN5T618_DCIRMON 0x42
@@ -221,8 +227,14 @@ enum {
RN5T618_REG_NUM,
};
+enum {
+ RN5T567 = 0,
+ RN5T618,
+};
+
struct rn5t618 {
struct regmap *regmap;
+ long variant;
};
#endif /* __LINUX_MFD_RN5T618_H */
--
2.8.3
More information about the linux-arm-kernel
mailing list