[PATCH v2 2/9] clk: imx: vf610: Disable automatic clock gating for lpuart in LPSTOP mode

[Bhuvanchandra DV]

From: Stefan Agner <stefan at agner.ch>

In order to allow wake support in STOP sleep mode, clocks are needed. Use
imx_clk_gate2_cgr to disable automatic clock gating in low power mode STOP.
This allows to enable wake by UART using:
echo enabled > /sys/class/tty/ttyLP0/power/wakeup

However, if wake is not enabled, the driver should disable the clocks explicitly
to save power.

Signed-off-by: Stefan Agner <stefan at agner.ch>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv at toradex.com>
---
 drivers/clk/imx/clk-vf610.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/drivers/clk/imx/clk-vf610.c b/drivers/clk/imx/clk-vf610.c
index 3a1f244..0476353 100644
--- a/drivers/clk/imx/clk-vf610.c
+++ b/drivers/clk/imx/clk-vf610.c
@@ -315,12 +315,12 @@ static void __init vf610_clocks_init(struct device_node *ccm_node)
 
 	clk[VF610_CLK_PIT] = imx_clk_gate2("pit", "ipg_bus", CCM_CCGR1, CCM_CCGRx_CGn(7));
 
-	clk[VF610_CLK_UART0] = imx_clk_gate2("uart0", "ipg_bus", CCM_CCGR0, CCM_CCGRx_CGn(7));
-	clk[VF610_CLK_UART1] = imx_clk_gate2("uart1", "ipg_bus", CCM_CCGR0, CCM_CCGRx_CGn(8));
-	clk[VF610_CLK_UART2] = imx_clk_gate2("uart2", "ipg_bus", CCM_CCGR0, CCM_CCGRx_CGn(9));
-	clk[VF610_CLK_UART3] = imx_clk_gate2("uart3", "ipg_bus", CCM_CCGR0, CCM_CCGRx_CGn(10));
-	clk[VF610_CLK_UART4] = imx_clk_gate2("uart4", "ipg_bus", CCM_CCGR6, CCM_CCGRx_CGn(9));
-	clk[VF610_CLK_UART5] = imx_clk_gate2("uart5", "ipg_bus", CCM_CCGR6, CCM_CCGRx_CGn(10));
+	clk[VF610_CLK_UART0] = imx_clk_gate2_cgr("uart0", "ipg_bus", CCM_CCGR0, CCM_CCGRx_CGn(7), 0x2);
+	clk[VF610_CLK_UART1] = imx_clk_gate2_cgr("uart1", "ipg_bus", CCM_CCGR0, CCM_CCGRx_CGn(8), 0x2);
+	clk[VF610_CLK_UART2] = imx_clk_gate2_cgr("uart2", "ipg_bus", CCM_CCGR0, CCM_CCGRx_CGn(9), 0x2);
+	clk[VF610_CLK_UART3] = imx_clk_gate2_cgr("uart3", "ipg_bus", CCM_CCGR0, CCM_CCGRx_CGn(10), 0x2);
+	clk[VF610_CLK_UART4] = imx_clk_gate2_cgr("uart4", "ipg_bus", CCM_CCGR6, CCM_CCGRx_CGn(9), 0x2);
+	clk[VF610_CLK_UART5] = imx_clk_gate2_cgr("uart5", "ipg_bus", CCM_CCGR6, CCM_CCGRx_CGn(10), 0x2);
 
 	clk[VF610_CLK_I2C0] = imx_clk_gate2("i2c0", "ipg_bus", CCM_CCGR4, CCM_CCGRx_CGn(6));
 	clk[VF610_CLK_I2C1] = imx_clk_gate2("i2c1", "ipg_bus", CCM_CCGR4, CCM_CCGRx_CGn(7));
-- 
2.9.0