[PATCH 2/4] input: touchscreen: crtouch_ts: Add driver
Anthony Felice
tony.felice at timesys.com
Fri Jun 24 12:44:44 PDT 2016
Add driver for the Vybrid Tower CRTouch-based touchscreen. This is
required for the touchscreen on the TWR-LCD-RGB to work on the Vybrid
Tower platform.
There is a known issue with this driver: rarely, SW1 on the TWR-LCD-RGB
module needs to be pressed in order for the touchscreen to begin
functioning.
Signed-off-by: Anthony Felice <tony.felice at timesys.com>
---
.../bindings/input/touchscreen/crtouch_ts.txt | 14 ++
drivers/input/touchscreen/Kconfig | 10 +
drivers/input/touchscreen/Makefile | 1 +
drivers/input/touchscreen/crtouch_ts.c | 279 +++++++++++++++++++++
4 files changed, 304 insertions(+)
create mode 100644 Documentation/devicetree/bindings/input/touchscreen/crtouch_ts.txt
create mode 100644 drivers/input/touchscreen/crtouch_ts.c
diff --git a/Documentation/devicetree/bindings/input/touchscreen/crtouch_ts.txt b/Documentation/devicetree/bindings/input/touchscreen/crtouch_ts.txt
new file mode 100644
index 0000000..cfb966c
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/crtouch_ts.txt
@@ -0,0 +1,14 @@
+* Freescale CRTOUCH based touchscreen
+
+Required Properties:
+- compatible must be fsl,crtouch_ts
+- reg: I2C address of the touchscreen
+- irq-gpio: GPIO to use as event IRQ
+
+Example:
+
+ touch: crtouch at 49 {
+ compatible = "fsl,crtouch_ts";
+ reg = <0x49>;
+ irq-gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>;
+ };
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index 8ecdc38..799e342 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -1155,4 +1155,14 @@ config TOUCHSCREEN_ROHM_BU21023
To compile this driver as a module, choose M here: the
module will be called bu21023_ts.
+config TOUCHSCREEN_CRTOUCH
+ tristate "Freescale CRTOUCH based touchscreen"
+ depends on I2C
+ help
+ Say Y here if you have a CRTOUCH based touchscreen
+ controller.
+
+ To compile this driver as a module, choose M here: the
+ module will be called crtouch_ts.
+
endif
diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
index f42975e..8cb0a7a 100644
--- a/drivers/input/touchscreen/Makefile
+++ b/drivers/input/touchscreen/Makefile
@@ -95,3 +95,4 @@ obj-$(CONFIG_TOUCHSCREEN_TPS6507X) += tps6507x-ts.o
obj-$(CONFIG_TOUCHSCREEN_ZFORCE) += zforce_ts.o
obj-$(CONFIG_TOUCHSCREEN_COLIBRI_VF50) += colibri-vf50-ts.o
obj-$(CONFIG_TOUCHSCREEN_ROHM_BU21023) += rohm_bu21023.o
+obj-$(CONFIG_TOUCHSCREEN_CRTOUCH) += crtouch_ts.o
diff --git a/drivers/input/touchscreen/crtouch_ts.c b/drivers/input/touchscreen/crtouch_ts.c
new file mode 100644
index 0000000..bb87a8e
--- /dev/null
+++ b/drivers/input/touchscreen/crtouch_ts.c
@@ -0,0 +1,279 @@
+/*
+ * Driver for Freescale Semiconductor CRTOUCH - A Resistive and Capacitive
+ * touch device with i2c interface
+ *
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/input.h>
+#include <linux/input/mt.h>
+#include <linux/slab.h>
+#include <linux/bitops.h>
+#include <linux/gpio.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+
+/* Resistive touch sense status registers */
+#define RES_STA_ERROR 0x00
+#define RES_STA_STATUS1 0x01
+#define RES_STA_STATUS2 0x02
+#define RES_STA_X_MSB 0x03
+#define RES_STA_X_LSB 0x04
+#define RES_STA_Y_MSB 0x05
+#define RES_STA_Y_LSB 0x06
+#define RES_STA_PRES_MSB 0x07
+#define RES_STA_RRES_LSB 0x08
+#define RES_STA_FIFO_STATUS 0x09
+#define RES_STA_FIFO_X_MSB 0x0a
+#define RES_STA_FIFO_X_LSB 0x0b
+#define RES_STA_FIFO_Y_MSB 0x0c
+#define RES_STA_FIFO_Y_LSB 0x0d
+#define RES_STA_FIFO_PRES_MSB 0x0e
+#define RES_STA_FIFO_PRES_LSB 0x0f
+#define RES_STA_UART_BRATE_MSB 0x10
+#define RES_STA_UART_BRATE_MID 0x11
+#define RES_STA_UART_BRATE_LSB 0x12
+#define RES_STA_DEV_IDEN 0x13
+#define RES_STA_SLIDE_DISPLACE 0x14
+#define RES_STA_ROTATE_ANGLE 0x15
+
+/* Resistive touch configuration registers */
+#define CR_CON_SYSTEM 0x40
+#define CR_CON_TRIG_EVENT 0x41
+#define CR_CON_FIFO_SETUP 0x42
+#define CR_CON_SAMPLING_RATE 0x43
+#define CR_CON_X_DELAY_MSB 0x44
+#define CR_CON_X_DELAY_LSB 0x45
+#define CR_CON_Y_DELAY_MSB 0x46
+#define CR_CON_Y_DELAY_LSB 0x47
+#define CR_CON_Z_DELAY_MSB 0x48
+#define CR_CON_Z_DELAY_LSB 0x49
+#define CR_CON_DIS_HOR_MSB 0x4a
+#define CR_CON_DIS_HOR_LSB 0x4b
+#define CR_CON_DIS_VER_MSB 0x4c
+#define CR_CON_DIS_VER_LSB 0x4d
+#define CR_CON_SLIDE_STEPS 0x4e
+
+#define RTST_EVENT BIT(7)
+#define RTS2T_EVENT BIT(6)
+#define RTSZ_EVENT BIT(5)
+#define RTSR_EVENT BIT(4)
+#define RTSS_EVENT BIT(3)
+#define RTSF_EVENT BIT(2)
+#define RTSRDY_EVENT BIT(0)
+
+#define RTSSD_MASK BIT(2)
+#define RTSSD_H_NEG BIT(2)
+#define RTSSD_V_POS BIT(3)
+#define RTSSD_V_NEG BIT(4)
+
+#define RTSRD_MASK BIT(4)
+#define RTSRD_COUNTER_CLK_WISE BIT(4)
+
+#define RTSZD_MASK BIT(5)
+#define RTSZD_ZOOM_OUT BIT(5)
+
+#define CRTOUCH_MAX_FINGER 2
+#define CRTOUCH_MAX_AREA 0xfff
+#define CRTOUCH_MAX_X 0x01df
+#define CRTOUCH_MAX_Y 0x010f
+
+struct crtouch_ts_data {
+ struct i2c_client *client;
+ struct input_dev *input_dev;
+};
+
+static u8 crtouch_read_reg(struct i2c_client *client, int addr)
+{
+ return i2c_smbus_read_byte_data(client, addr);
+}
+
+static int crtouch_write_reg(struct i2c_client *client, int addr, int data)
+{
+ return i2c_smbus_write_byte_data(client, addr, data);
+}
+
+static void calibration_pointer(u16 *x_orig, u16 *y_orig)
+{
+ u16 x, y;
+
+ x = CRTOUCH_MAX_X - *x_orig;
+ *x_orig = x;
+
+ y = CRTOUCH_MAX_Y - *y_orig;
+ *y_orig = y;
+}
+
+static irqreturn_t crtouch_ts_interrupt(int irq, void *dev_id)
+{
+ struct crtouch_ts_data *data = dev_id;
+ struct i2c_client *client = data->client;
+ u8 status1;
+ u16 valuep, valuex, valuey;
+
+ status1 = crtouch_read_reg(client, RES_STA_STATUS1);
+
+ /* For single touch */
+ if (status1 & RTST_EVENT) {
+ valuep = crtouch_read_reg(client, RES_STA_PRES_MSB);
+ valuep = ((valuep << 8) |
+ crtouch_read_reg(client, RES_STA_RRES_LSB));
+ valuex = crtouch_read_reg(client, RES_STA_X_MSB);
+ valuex = ((valuex << 8) |
+ crtouch_read_reg(client, RES_STA_X_LSB));
+ valuey = crtouch_read_reg(client, RES_STA_Y_MSB);
+ valuey = ((valuey << 8) |
+ crtouch_read_reg(client, RES_STA_Y_LSB));
+ calibration_pointer(&valuex, &valuey);
+ input_report_key(data->input_dev, BTN_TOUCH, 1);
+ input_report_abs(data->input_dev, ABS_X, valuex);
+ input_report_abs(data->input_dev, ABS_Y, valuey);
+ input_report_abs(data->input_dev, ABS_PRESSURE, valuep);
+ input_sync(data->input_dev);
+ } else {
+ input_report_abs(data->input_dev, ABS_PRESSURE, 0);
+ input_event(data->input_dev, EV_KEY, BTN_TOUCH, 0);
+ input_sync(data->input_dev);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static void crtouch_ts_reg_init(struct crtouch_ts_data *data)
+{
+ struct i2c_client *client = data->client;
+
+ crtouch_write_reg(client, CR_CON_SYSTEM, 0x9c);
+ crtouch_write_reg(client, CR_CON_TRIG_EVENT, 0xf9);
+ crtouch_write_reg(client, CR_CON_FIFO_SETUP, 0x1f);
+ crtouch_write_reg(client, CR_CON_SAMPLING_RATE, 0x08);
+ crtouch_write_reg(client, CR_CON_DIS_HOR_MSB, 0x01);
+ crtouch_write_reg(client, CR_CON_DIS_HOR_LSB, 0xdf);
+ crtouch_write_reg(client, CR_CON_DIS_VER_MSB, 0x01);
+ crtouch_write_reg(client, CR_CON_DIS_VER_LSB, 0x0f);
+}
+
+static int crtouch_ts_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct crtouch_ts_data *data;
+ struct input_dev *input_dev;
+ int error = -1, irq_gpio;
+
+ dev_info(&client->dev, "Freescale CRTOUCH driver\n");
+
+ data = kzalloc(sizeof(*data), GFP_KERNEL);
+ input_dev = input_allocate_device();
+ if (!data || !input_dev) {
+ dev_err(&client->dev, "Failed to allocate memory\n");
+ error = -ENOMEM;
+ goto err_free_mem;
+ }
+
+ data->client = client;
+ data->input_dev = input_dev;
+
+ input_dev->name = "crtouch_ts";
+ input_dev->id.bustype = BUS_I2C;
+ input_dev->dev.parent = &client->dev;
+
+ /* For single touch */
+ __set_bit(EV_KEY, input_dev->evbit);
+ __set_bit(BTN_TOUCH, input_dev->keybit);
+ __set_bit(EV_ABS, input_dev->evbit);
+ __set_bit(ABS_X, input_dev->absbit);
+ __set_bit(ABS_Y, input_dev->absbit);
+ __set_bit(ABS_PRESSURE, input_dev->absbit);
+
+ input_set_abs_params(input_dev, ABS_X, 0, CRTOUCH_MAX_X, 0, 0);
+ input_set_abs_params(input_dev, ABS_Y, 0, CRTOUCH_MAX_Y, 0, 0);
+ input_set_abs_params(input_dev, ABS_PRESSURE, 0,
+ CRTOUCH_MAX_AREA, 0, 0);
+
+ input_set_drvdata(input_dev, data);
+
+ crtouch_ts_reg_init(data);
+
+ irq_gpio = of_get_named_gpio(client->dev.of_node, "irq-gpio", 0);
+ if (!gpio_is_valid(irq_gpio))
+ goto err_free_mem;
+
+ error = gpio_request_one(irq_gpio, GPIOF_IN, "TS_IRQ");
+ if (error) {
+ dev_err(&client->dev, "Failed to request gpio\n");
+ goto err_free_mem;
+ }
+
+ error = request_threaded_irq(gpio_to_irq(irq_gpio), NULL,
+ crtouch_ts_interrupt,
+ IRQF_ONESHOT | IRQF_TRIGGER_FALLING,
+ "crtouch_ts", data);
+
+ if (error) {
+ dev_err(&client->dev, "Failed to register interrupt\n");
+ goto err_free_mem;
+ }
+
+ error = input_register_device(data->input_dev);
+ if (error)
+ goto err_free_irq;
+
+ i2c_set_clientdata(client, data);
+ return 0;
+
+err_free_irq:
+ free_irq(client->irq, data);
+err_free_mem:
+ input_free_device(input_dev);
+ kfree(data);
+ return error;
+}
+
+static int crtouch_ts_remove(struct i2c_client *client)
+{
+ struct crtouch_ts_data *data = i2c_get_clientdata(client);
+
+ free_irq(client->irq, data);
+ input_unregister_device(data->input_dev);
+ kfree(data);
+
+ return 0;
+}
+
+static const struct i2c_device_id crtouch_ts_id[] = {
+ {"crtouch_ts", 0},
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, crtouch_ts_id);
+
+static const struct of_device_id crtouch_ts_dt_ids[] = {
+ { .compatible = "fsl,crtouch_ts", },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, crtouch_ts_dt_ids);
+
+static struct i2c_driver crtouch_ts_i2c_driver = {
+ .driver = {
+ .name = "crtouch_ts",
+ .owner = THIS_MODULE,
+ .of_match_table = crtouch_ts_dt_ids,
+ },
+ .probe = crtouch_ts_probe,
+ .remove = crtouch_ts_remove,
+ .id_table = crtouch_ts_id,
+};
+
+module_i2c_driver(crtouch_ts_i2c_driver);
+
+MODULE_AUTHOR("Alison Wang <b18965 at freescale.com>");
+MODULE_DESCRIPTION("Touchscreen driver for Freescale CRTOUCH");
+MODULE_LICENSE("GPL");
--
2.7.4
More information about the linux-arm-kernel
mailing list