[PATCH] ARM: sun8i: Add Parrot Board DTS
Chen-Yu Tsai
wens at csie.org
Mon Jun 20 09:30:25 PDT 2016
Hi,
On Mon, Jun 20, 2016 at 11:44 PM, Maxime Ripard
<maxime.ripard at free-electrons.com> wrote:
> Hi,
>
> On Tue, Jun 14, 2016 at 09:19:58PM +0800, Chen-Yu Tsai wrote:
>> On Tue, Jun 14, 2016 at 8:59 PM, Quentin Schulz
>> <quentin.schulz at free-electrons.com> wrote:
>> > Hi,
>> >
>> > On 13/06/2016 15:04, Chen-Yu Tsai wrote:
>> >> Hi,
>> >>
>> >> On Mon, Jun 13, 2016 at 6:15 PM, Quentin Schulz
>> >> <quentin.schulz at free-electrons.com> wrote:
>> >>> The Parrot Board is an evaluation board with an Allwinner R16 (assumed
>> >>> to be close to an Allwinner A33), 4GB of NAND, 512MB of RAM, USB host
>> >>
>> >> You say NAND here, but you enable mmc2 for eMMC below. Please correct it.
>> >>
>> >
>> > ACK.
>> >
>> >>> and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2
>> >>> controllable buttons, an LVDS port with separated backlight and
>> >>> capacitive touch panel ports, an audio/microphone jack, a camera CSI
>> >>> port, 2 sets of 22 GPIOs and an accelerometer.
>> >>
>> >> I assume the board is this one:
>> >>
>> >> https://world.taobao.com/item/530374411673.htm
>> >>
>> >
>> > Definitely looks like it.
>> >
>> >>> Signed-off-by: Quentin Schulz <quentin.schulz at free-electrons.com>
>> >>> ---
>> >>> arch/arm/boot/dts/Makefile | 1 +
>> >>> arch/arm/boot/dts/sun8i-r16-parrot.dts | 333 +++++++++++++++++++++++++++++++++
>> >>> 2 files changed, 334 insertions(+)
>> >>> create mode 100644 arch/arm/boot/dts/sun8i-r16-parrot.dts
>> >>>
>> >>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> >>> index 06b6c2d..1149512 100644
>> >>> --- a/arch/arm/boot/dts/Makefile
>> >>> +++ b/arch/arm/boot/dts/Makefile
>> >>> @@ -760,6 +760,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
>> >>> sun8i-a33-ippo-q8h-v1.2.dtb \
>> >>> sun8i-a33-q8-tablet.dtb \
>> >>> sun8i-a33-sinlinx-sina33.dtb \
>> >>> + sun8i-r16-parrot.dtb \
>> >>> sun8i-a83t-allwinner-h8homlet-v2.dtb \
>> >>> sun8i-a83t-cubietruck-plus.dtb \
>> >>> sun8i-h3-orangepi-2.dtb \
>> >>> diff --git a/arch/arm/boot/dts/sun8i-r16-parrot.dts b/arch/arm/boot/dts/sun8i-r16-parrot.dts
>> >>> new file mode 100644
>> >>> index 0000000..75e2420
>> >>> --- /dev/null
>> >>> +++ b/arch/arm/boot/dts/sun8i-r16-parrot.dts
>> >>> @@ -0,0 +1,333 @@
>> >>> +/*
>> >>> + * Copyright 2015 Quentin Schulz
>> >>> + *
>> >>> + * Quentin Schulz <quentin.schulz at free-electrons.com>
>> >>> + *
>> >>> + * This file is dual-licensed: you can use it either under the terms
>> >>> + * of the GPL or the X11 license, at your option. Note that this dual
>> >>> + * licensing only applies to this file, and not this project as a
>> >>> + * whole.
>> >>> + *
>> >>> + * a) This file is free software; you can redistribute it and/or
>> >>> + * modify it under the terms of the GNU General Public License as
>> >>> + * published by the Free Software Foundation; either version 2 of the
>> >>> + * License, or (at your option) any later version.
>> >>> + *
>> >>> + * This file is distributed in the hope that it will be useful,
>> >>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> >>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> >>> + * GNU General Public License for more details.
>> >>> + *
>> >>> + * Or, alternatively,
>> >>> + *
>> >>> + * b) Permission is hereby granted, free of charge, to any person
>> >>> + * obtaining a copy of this software and associated documentation
>> >>> + * files (the "Software"), to deal in the Software without
>> >>> + * restriction, including without limitation the rights to use,
>> >>> + * copy, modify, merge, publish, distribute, sublicense, and/or
>> >>> + * sell copies of the Software, and to permit persons to whom the
>> >>> + * Software is furnished to do so, subject to the following
>> >>> + * conditions:
>> >>> + *
>> >>> + * The above copyright notice and this permission notice shall be
>> >>> + * included in all copies or substantial portions of the Software.
>> >>> + *
>> >>> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
>> >>> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
>> >>> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
>> >>> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
>> >>> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
>> >>> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
>> >>> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
>> >>> + * OTHER DEALINGS IN THE SOFTWARE.
>> >>> + */
>> >>> +
>> >>> +/dts-v1/;
>> >>> +#include "sun8i-a33.dtsi"
>> >>> +#include "sunxi-common-regulators.dtsi"
>> >>> +
>> >>> +#include <dt-bindings/gpio/gpio.h>
>> >>> +#include <dt-bindings/input/input.h>
>> >>> +
>> >>> +/ {
>> >>> + model = "Allwinner Parrot EVB R16";
>> >>> + compatible = "allwinner,parrot-evb-r16", "allwinner,sun8i-a33";
>> >>> +
>> >>> + aliases {
>> >>> + serial0 = &uart0;
>> >>> + };
>> >>> +
>> >>> + chosen {
>> >>> + stdout-path = "serial0:115200n8";
>> >>> + };
>> >>> +
>> >>> + leds {
>> >>> + compatible = "gpio-leds";
>> >>> + pinctrl-names = "default";
>> >>> + pinctrl-0 = <&led_pins_r16>;
>> >>
>> >> IMO r16 is too generic. You may want to add parrot_ or parrot_evb_ to it.
>> >> Same goes for all the other r16 identifier names.
>> >>
>> >
>> > ACK.
>> >
>> >>> +
>> >>> + led1 {
>> >>> + label = "r16:led1:usr";
>> >>> + gpio = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */
>> >>> + };
>> >>> +
>> >>> + led2 {
>> >>> + label = "r16:led2:usr";
>> >>> + gpio = <&pio 4 16 GPIO_ACTIVE_HIGH>; /* PE16 */
>> >>> + };
>> >>> + };
>> >>> +
>> >>> + wifi_pwrseq: wifi_pwrseq {
>> >>> + compatible = "mmc-pwrseq-simple";
>> >>> + reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL06 */
>> >>> + };
>> >>> +
>> >>> +};
>> >>> +
>> >>> +&ehci0 {
>> >>> + status = "okay";
>> >>> +};
>> >>> +
>> >>> +&i2c1 {
>> >>> + pinctrl-names = "default";
>> >>> + pinctrl-0 = <&i2c1_pins_a>;
>> >>> + status = "okay";
>> >>
>> >> Nothing connected? A comment mentioning which connector this is on
>> >> if it's not directly connecting something on the board would be nice.
>> >>
>> >
>> > An accelerometer is connected to this i2c, but:
>> > 1) The given address of the i2c device given by i2cdetect is not the
>> > same as specified in both fex and schematics.
>> > 2) The accelerometer has a "product reference" on the schematics for a
>> > Broadcom BMA250 but the associated driver does not work with it.
>> >
>> > So there is an accelerometer connected to this i2c but I've not found
>> > yet what can drive it. I could add a comment specifying the
>> > accelerometer is attached to this i2c or remove the node?
>>
>> A comment will suffice, until you figure out what exactly is on there.
>>
>> >
>> >>> +};
>> >>> +
>> >>> +&lradc {
>> >>> + vref-supply = <®_aldo3>;
>> >>> + status = "okay";
>> >>> +
>> >>> + button at 0 {
>> >>> + label = "V+";
>> >>> + linux,code = <KEY_VOLUMEUP>;
>> >>> + channel = <0>;
>> >>> + voltage = <190000>;
>> >>> + };
>> >>> +
>> >>> + button at 1 {
>> >>> + label = "V-";
>> >>> + linux,code = <KEY_VOLUMEDOWN>;
>> >>> + channel = <0>;
>> >>> + voltage = <390000>;
>> >>> + };
>> >>> +
>> >>> +};
>> >>> +
>> >>> +&mmc0 {
>> >>> + pinctrl-names = "default";
>> >>> + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_parrot>;
>> >>> + vmmc-supply = <®_dcdc1>;
>> >>> + cd-gpios = <&pio 3 14 GPIO_ACTIVE_LOW>; /* PD14 */
>> >>> + bus-width = <4>;
>> >>> + status = "okay";
>> >>> +};
>> >>> +
>> >>> +&mmc1 {
>> >>> + pinctrl-names = "default";
>> >>> + pinctrl-0 = <&mmc1_pins_a>, <&wifi_reset_pin_r16>;
>> >>> + vmmc-supply = <®_aldo1>;
>> >>
>> >> This looks fishy. See below.
>> >>
>> >>> + mmc-pwrseq = <&wifi_pwrseq>;
>> >>> + bus-width = <4>;
>> >>> + non-removable;
>> >>> + status = "okay";
>> >>> +};
>> >>> +
>> >>> +&mmc2 {
>> >>> + pinctrl-names = "default";
>> >>> + pinctrl-0 = <&mmc2_8bit_pins>;
>> >>> + vmmc-supply = <®_dcdc1>;
>> >>> + bus-width = <8>;
>> >>> + non-removable;
>> >>> + cap-mmc-hw-reset;
>> >>> + status = "okay";
>> >>> +};
>> >>> +
>> >>> +&mmc2_8bit_pins {
>> >>> + allwinner,drive = <SUN4I_PINCTRL_40_MA>;
>> >>> + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
>> >>> +};
>> >>> +
>> >>> +&ohci0 {
>> >>> + status = "okay";
>> >>> +};
>> >>> +
>> >>> +&pio {
>> >>> + mmc0_cd_pin_parrot: mmc0_cd_pin at 0 {
>> >>
>> >> _parrot suffix works as well.
>> >>
>> >>> + allwinner,pins = "PD14";
>> >>> + allwinner,function = "gpio_in";
>> >>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> >>> + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
>> >>> + };
>> >>> +
>> >>> + led_pins_r16: led_pins at 0 {
>> >>> + allwinner,pins = "PE16", "PE17";
>> >>> + allwinner,function = "gpio_out";
>> >>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> >>> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> >>> + };
>> >>> +
>> >>> + usb0_id_det: usb0_id_detect_pin at 0 {
>> >>> + allwinner,pins = "PD10";
>> >>> + allwinner,function = "gpio_in";
>> >>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> >>> + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
>> >>> + };
>> >>> +
>> >>> + usb1_vbus_pin_r16: usb1_vbus_pin at 0 {
>> >>> + allwinner,pins = "PD12";
>> >>> + allwinner,function = "gpio_out";
>> >>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> >>> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> >>> + };
>> >>> +};
>> >>> +
>> >>> +&r_pio {
>> >>> + wifi_reset_pin_r16: wifi_reset_pin at 3 {
>> >>
>> >> Why @3?
>> >>
>> >
>> > This is a typo, I'll correct it.
>> >
>> >>> + allwinner,pins = "PL6";
>> >>> + allwinner,function = "gpio_out";
>> >>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> >>> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> >>> + };
>> >>> +};
>> >>> +
>> >>> +&r_rsb {
>> >>> + status = "okay";
>> >>> +
>> >>> + axp22x: pmic at 3a3 {
>> >>> + compatible = "x-powers,axp223";
>> >>> + reg = <0x3a3>;
>> >>> + interrupt-parent = <&nmi_intc>;
>> >>> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
>> >>> + eldoin-supply = <®_dcdc1>;
>> >>
>> >> A drivevbus-supply referencing reg_vcc5v0 here would be better.
>> >>
>> >
>> > ACK.
>> >
>> >>> + x-powers,drive-vbus-en;
>> >>> + };
>> >>> +};
>> >>> +
>> >>> +#include "axp22x.dtsi"
>> >>> +
>> >>> +®_aldo1 {
>> >>> + regulator-always-on;
>> >>> + regulator-min-microvolt = <3000000>;
>> >>> + regulator-max-microvolt = <3000000>;
>> >>> + regulator-name = "aldo1";
>> >>
>> >> What is this for exactly? Would turning it off render the system inoperable?
>> >> How was it referenced in the fex file?
>> >>
>> >> If this is for WiFi I/O VCC, then you should specify it in mmc1 with
>> >> vqmmc-supply.
>> >>
>> >
>> > In the fex, aldo1 is one of the three power inputs for the WiFi (the
>> > others being dldo1 and dldo2) and in the schematics it is linked to
>> > both VCC-USB and VCC-IO-WIFI.
>> >
>> > I tried to turn it off and, indeed, the system becomes inoperable.
>> >
>> > I'll add vqmmc-supply in mmc1 with aldo1 regulator. However, I am
>> > wondering what to put in vmmc-supply for mmc1 since the WiFi module has
>> > three power inputs: dldo1, dldo2 and aldo1. In the fex, they are
>> > referenced as, respectively, module_power1, module_power2 and
>> > module_power3 and in the schematics dldo1 and dldo2 are named VCC-WIFI
>> > while aldo1 is used for VCC-IO-WIFI (if it can help in any way).
>> >
>> > VCC-WIFI is connected to pin VBAT of the Broadcom AP6212 WiFi chip.
>> > VCC-IO-WIFI is connected to pin VDDIO of the chip.
>>
>> VCC-IO-WIFI is vqmmc, and VCC-WIFI is vmmc.
>
> Isn't vmmc supposed to be always powered at 3.3v, and vqmmc the one
> used to drop to 1.8V with the UHS cards?
For eMMC, vmmc and vqmmc correspond to the pins on the eMMC chip.
vmmc provides power to the internals, while vqmmc provides power to the
I/O buffers on both sides. With SD this is a bit less clear. IIUC the SD
card itself supplies I/O voltage, dropping it to 1.8V if necessary, from
VDD (vmmc). vqmmc only affects the host side, and whatever external pull-ups
that might exist.
> In which case, VCC-IO-WIFI is vmmc, and VCC-WIFI is just one of the
> wifi chip power rail, to be handled by a power sequence.
For the WiFi chip, there is a separate IO-VCC rail, which is VCC-IO-WIFI.
This, from what I understand of the datasheet, is for I/O signaling, and
thus vqmmc. VCC-WIFI is what powers the chip, which is what vmmc is.
>> About having 2 regulators, Maxime is working on a solution. In the
>> meantime, you could have dldo1/dldo2 always-on, and put a TODO
>> comment on them.
>
> Yep.
>
>> Not sure about it also linked to VCC-USB though. Is VCC-USB connected
>> to the SoC or just a trace on the board? If it's the latter, it might
>> also be designed to work with a USB based WiFi module.
>
> It seems to be one of the inputs of the SoC.
A33 datasheet has a "VCC-USB" power pin, which it says is "Power supply
for the USB PHY". This should probably be tied to the USB PHY node. The
PHY framework has a common "phy-supply" property, though I don't know if
it works with sunxi's multiple PHY per node approach.
Regards
ChenYu
More information about the linux-arm-kernel
mailing list