[RFC] can: c_can: Update D_CAN TX and RX functions to 32 bit.

[tthayer at opensource.altera.com]

From: Thor Thayer <tthayer at opensource.altera.com>

When testing CAN write floods on Altera's CycloneV, the
first 2 bytes are sometimes 0x00, 0x00 or corrupted
instead of the values sent. Also observed bytes 4 & 5
were corrupted in some cases.

The D_CAN Data registers are 32 bits and changing from
16 bit writes to 32 bit writes fixes the problem.

Testing performed on Altera CycloneV (D_CAN).
Requesting tests on other C_CAN & D_CAN platforms.

Reported-by: Richard Andrysek <richard.andrysek at gomtec.de>
Signed-off-by: Thor Thayer <tthayer at opensource.altera.com>
---
 drivers/net/can/c_can/c_can.c |   38 +++++++++++++++++++++++++++++++-------
 1 file changed, 31 insertions(+), 7 deletions(-)

diff --git a/drivers/net/can/c_can/c_can.c b/drivers/net/can/c_can/c_can.c
index f91b094..e3dccd3 100644
--- a/drivers/net/can/c_can/c_can.c
+++ b/drivers/net/can/c_can/c_can.c
@@ -332,9 +332,23 @@ static void c_can_setup_tx_object(struct net_device *dev, int iface,
 
 	priv->write_reg(priv, C_CAN_IFACE(MSGCTRL_REG, iface), ctrl);
 
-	for (i = 0; i < frame->can_dlc; i += 2) {
-		priv->write_reg(priv, C_CAN_IFACE(DATA1_REG, iface) + i / 2,
-				frame->data[i] | (frame->data[i + 1] << 8));
+	if (priv->type == BOSCH_D_CAN) {
+		u32 data = 0, dreg = C_CAN_IFACE(DATA1_REG, iface);
+
+		for (i = 0; i < frame->can_dlc; i += 4, dreg += 2) {
+			data = (u32)frame->data[i];
+			data |= (u32)frame->data[i + 1] << 8;
+			data |= (u32)frame->data[i + 2] << 16;
+			data |= (u32)frame->data[i + 3] << 24;
+			priv->write_reg32(priv, dreg, data);
+		}
+	} else {
+		for (i = 0; i < frame->can_dlc; i += 2) {
+			priv->write_reg(priv,
+					C_CAN_IFACE(DATA1_REG, iface) + i / 2,
+					frame->data[i] |
+					(frame->data[i + 1] << 8));
+		}
 	}
 }
 
@@ -402,10 +416,20 @@ static int c_can_read_msg_object(struct net_device *dev, int iface, u32 ctrl)
 	} else {
 		int i, dreg = C_CAN_IFACE(DATA1_REG, iface);
 
-		for (i = 0; i < frame->can_dlc; i += 2, dreg ++) {
-			data = priv->read_reg(priv, dreg);
-			frame->data[i] = data;
-			frame->data[i + 1] = data >> 8;
+		if (priv->type == BOSCH_D_CAN) {
+			for (i = 0; i < frame->can_dlc; i += 4, dreg += 2) {
+				data = priv->read_reg32(priv, dreg);
+				frame->data[i] = data;
+				frame->data[i + 1] = data >> 8;
+				frame->data[i + 2] = data >> 16;
+				frame->data[i + 3] = data >> 24;
+			}
+		} else {
+			for (i = 0; i < frame->can_dlc; i += 2, dreg++) {
+				data = priv->read_reg(priv, dreg);
+				frame->data[i] = data;
+				frame->data[i + 1] = data >> 8;
+			}
 		}
 	}
 
-- 
1.7.9.5