[PATCH 4/5] clk: max77686: Add support for MAX77620 clocks

Krzysztof Kozlowski k.kozlowski at samsung.com
Thu Jun 16 02:54:31 PDT 2016


On 06/15/2016 04:13 PM, Laxman Dewangan wrote:
> Maxim Max77620 has one 32KHz clock output and the clock HW
> IP used on this PMIC is same as what it is there in the MAX77686.
> 
> Add clock driver support for MAX77620 on the MAX77686 driver.
> 
> Signed-off-by: Laxman Dewangan <ldewangan at nvidia.com>
> CC: Krzysztof Kozlowski <k.kozlowski at samsung.com>
> CC: Javier Martinez Canillas <javier at dowhile0.org>
> ---
>  drivers/clk/Kconfig        |  7 ++++---
>  drivers/clk/clk-max77686.c | 16 ++++++++++++++++
>  2 files changed, 20 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
> index 6afad74..d75f4c5 100644
> --- a/drivers/clk/Kconfig
> +++ b/drivers/clk/Kconfig
> @@ -32,10 +32,11 @@ config COMMON_CLK_WM831X
>  source "drivers/clk/versatile/Kconfig"
>  
>  config COMMON_CLK_MAX77686
> -	tristate "Clock driver for Maxim 77686/77802 MFD"
> -	depends on MFD_MAX77686
> +	tristate "Clock driver for Maxim 77686/77802/MAX77620 MFD"
> +	depends on MFD_MAX77686 || MFD_MAX77620
>  	---help---
> -	  This driver supports Maxim 77686/77802 crystal oscillator clock.
> +	  This driver supports Maxim 77686/77802/MAX77620 crystal oscillator
> +	  clock.
>  
>  config COMMON_CLK_RK808
>  	tristate "Clock driver for RK808"
> diff --git a/drivers/clk/clk-max77686.c b/drivers/clk/clk-max77686.c
> index 31ba726..d2be736 100644
> --- a/drivers/clk/clk-max77686.c
> +++ b/drivers/clk/clk-max77686.c
> @@ -19,6 +19,7 @@
>  #include <linux/err.h>
>  #include <linux/module.h>
>  #include <linux/platform_device.h>
> +#include <linux/mfd/max77620.h>
>  #include <linux/mfd/max77686.h>
>  #include <linux/mfd/max77686-private.h>
>  #include <linux/clk-provider.h>
> @@ -30,12 +31,14 @@
>  
>  #include <dt-bindings/clock/maxim,max77686.h>
>  #include <dt-bindings/clock/maxim,max77802.h>
> +#include <dt-bindings/mfd/max77620.h>
>  
>  #define MAX77802_CLOCK_LOW_JITTER_SHIFT 0x3
>  
>  enum chip_name {
>  	CHIP_MAX77686,
>  	CHIP_MAX77802,
> +	CHIP_MAX77620,

Now it is more obvious why it is here. However I don't like the
duplication of device IDs, under different names and different values:
1. include/linux/mfd/max77686-private.h
2. include/linux/mfd/max77620.h
3. here

I was thinking about way of combining it... but these headers are
different. Unless there will be one header for all three devices.

Anyway, please add the max77686 prefix to the enum.

Best regards,
Krzysztof

>  };
>  
>  struct max_gen_hw_clk_data {
> @@ -91,6 +94,14 @@ static struct max_gen_hw_clk_data max77802_hw_clks_info[MAX77802_CLKS_NUM] = {
>  	},
>  };
>  
> +static struct max_gen_hw_clk_data max77620_hw_clks_info[MAX77620_CLKS_NUM] = {
> +	[MAX77620_CLK_32K_OUT0] = {
> +		.name = "32khz_pmic",
> +		.reg = MAX77620_REG_CNFG1_32K,
> +		.mask = MAX77620_CNFG1_32K_OUT0_EN,
> +	},
> +};
> +
>  static struct max_gen_clk_data *to_max_gen_clk_data(struct clk_hw *hw)
>  {
>  	return container_of(hw, struct max_gen_clk_data, hw);
> @@ -171,6 +182,10 @@ static int max77686_clk_probe(struct platform_device *pdev)
>  		num_clks = MAX77802_CLKS_NUM;
>  		hw_clks = max77802_hw_clks_info;
>  		break;
> +	case CHIP_MAX77620:
> +		num_clks = MAX77620_CLKS_NUM;
> +		hw_clks = max77620_hw_clks_info;
> +		break;
>  	default:
>  		dev_err(dev, "Unknown Chip ID\n");
>  		return -EINVAL;
> @@ -269,6 +284,7 @@ static int max77686_clk_remove(struct platform_device *pdev)
>  static const struct platform_device_id max77686_clk_id[] = {
>  	{ "max77686-clk", .driver_data = (kernel_ulong_t)CHIP_MAX77686, },
>  	{ "max77802-clk", .driver_data = (kernel_ulong_t)CHIP_MAX77802, },
> +	{ "max77620-clock", .driver_data = (kernel_ulong_t)CHIP_MAX77620, },
>  	{},
>  };
>  MODULE_DEVICE_TABLE(platform, max77686_clk_id);
> 




More information about the linux-arm-kernel mailing list