[PATCH 2/2] ARM: OMAP2+: Drop legacy board file for LDP
Tony Lindgren
tony at atomide.com
Wed Jun 15 03:48:09 PDT 2016
Let's drop the last two remaining omap3 legacy boot board files.
Let's only use the device tree based booting known to work for
these two boards.
We still have two omap3 boards booting in legacy mode in addition
to device tree based booting. All the other ten or so omap2+ SoCs
have been booting using device tree mode only for years now. This
has allowed us to get rid of quite a bit of arch/arm/mach-omap2
related platform init code in favor of dts and driver changes.
Pretty much the only remaining known users for omap3 legacy boot
board files are Kevin's and Russell's boot test systems, and N900
kernel tree maintained by Pali and Ivaylo. And all of them are
also supporting the device tree based booting. The legacy booting
mode has been kept around mostly to verify against regressions.
As there is still a slim chance of possible other uses of the
mainline kernel for these boards, let's just drop the board
files for v4.8, and let's not touch the related platform init
code until around v4.9 time if no issues are found. This makes
it trivial for us to add back the board files with a simple revert.
Signed-off-by: Tony Lindgren <tony at atomide.com>
---
arch/arm/mach-omap2/Kconfig | 6 -
arch/arm/mach-omap2/Makefile | 1 -
arch/arm/mach-omap2/board-ldp.c | 429 ----------------------------------------
3 files changed, 436 deletions(-)
delete mode 100644 arch/arm/mach-omap2/board-ldp.c
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 3c6b070..9f15235 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -188,12 +188,6 @@ config MACH_OMAP2_TUSB6010
depends on ARCH_OMAP2 && SOC_OMAP2420
default y if MACH_NOKIA_N8X0
-config MACH_OMAP_LDP
- bool "OMAP3 LDP board"
- depends on ARCH_OMAP3
- default y
- select OMAP_PACKAGE_CBB
-
config MACH_OMAP3517EVM
bool "OMAP3517/ AM3517 EVM board"
depends on ARCH_OMAP3
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index 8660889..7ab35eb 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -228,7 +228,6 @@ obj-$(CONFIG_SOC_OMAP2420) += msdi.o
# Specific board support
obj-$(CONFIG_MACH_OMAP_GENERIC) += board-generic.o pdata-quirks.o
-obj-$(CONFIG_MACH_OMAP_LDP) += board-ldp.o
obj-$(CONFIG_MACH_NOKIA_N8X0) += board-n8x0.o
# Platform specific device init code
diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c
deleted file mode 100644
index d9c3ffc..0000000
--- a/arch/arm/mach-omap2/board-ldp.c
+++ /dev/null
@@ -1,429 +0,0 @@
-/*
- * linux/arch/arm/mach-omap2/board-ldp.c
- *
- * Copyright (C) 2008 Texas Instruments Inc.
- * Nishant Kamat <nskamat at ti.com>
- *
- * Modified from mach-omap2/board-3430sdp.c
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/input.h>
-#include <linux/input/matrix_keypad.h>
-#include <linux/gpio_keys.h>
-#include <linux/workqueue.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/spi/spi.h>
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-#include <linux/i2c/twl.h>
-#include <linux/io.h>
-#include <linux/smsc911x.h>
-#include <linux/mmc/host.h>
-#include <linux/usb/phy.h>
-#include <linux/platform_data/spi-omap2-mcspi.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-#include "gpmc.h"
-#include "gpmc-smsc911x.h"
-
-#include <video/omapdss.h>
-#include <video/omap-panel-data.h>
-
-#include "board-flash.h"
-#include "mux.h"
-#include "hsmmc.h"
-#include "control.h"
-#include "common-board-devices.h"
-
-#define LDP_SMSC911X_CS 1
-#define LDP_SMSC911X_GPIO 152
-#define DEBUG_BASE 0x08000000
-#define LDP_ETHR_START DEBUG_BASE
-
-static uint32_t board_keymap[] = {
- KEY(0, 0, KEY_1),
- KEY(1, 0, KEY_2),
- KEY(2, 0, KEY_3),
- KEY(0, 1, KEY_4),
- KEY(1, 1, KEY_5),
- KEY(2, 1, KEY_6),
- KEY(3, 1, KEY_F5),
- KEY(0, 2, KEY_7),
- KEY(1, 2, KEY_8),
- KEY(2, 2, KEY_9),
- KEY(3, 2, KEY_F6),
- KEY(0, 3, KEY_F7),
- KEY(1, 3, KEY_0),
- KEY(2, 3, KEY_F8),
- PERSISTENT_KEY(4, 5),
- KEY(4, 4, KEY_VOLUMEUP),
- KEY(5, 5, KEY_VOLUMEDOWN),
- 0
-};
-
-static struct matrix_keymap_data board_map_data = {
- .keymap = board_keymap,
- .keymap_size = ARRAY_SIZE(board_keymap),
-};
-
-static struct twl4030_keypad_data ldp_kp_twl4030_data = {
- .keymap_data = &board_map_data,
- .rows = 6,
- .cols = 6,
- .rep = 1,
-};
-
-static struct gpio_keys_button ldp_gpio_keys_buttons[] = {
- [0] = {
- .code = KEY_ENTER,
- .gpio = 101,
- .desc = "enter sw",
- .active_low = 1,
- .debounce_interval = 30,
- },
- [1] = {
- .code = KEY_F1,
- .gpio = 102,
- .desc = "func 1",
- .active_low = 1,
- .debounce_interval = 30,
- },
- [2] = {
- .code = KEY_F2,
- .gpio = 103,
- .desc = "func 2",
- .active_low = 1,
- .debounce_interval = 30,
- },
- [3] = {
- .code = KEY_F3,
- .gpio = 104,
- .desc = "func 3",
- .active_low = 1,
- .debounce_interval = 30,
- },
- [4] = {
- .code = KEY_F4,
- .gpio = 105,
- .desc = "func 4",
- .active_low = 1,
- .debounce_interval = 30,
- },
- [5] = {
- .code = KEY_LEFT,
- .gpio = 106,
- .desc = "left sw",
- .active_low = 1,
- .debounce_interval = 30,
- },
- [6] = {
- .code = KEY_RIGHT,
- .gpio = 107,
- .desc = "right sw",
- .active_low = 1,
- .debounce_interval = 30,
- },
- [7] = {
- .code = KEY_UP,
- .gpio = 108,
- .desc = "up sw",
- .active_low = 1,
- .debounce_interval = 30,
- },
- [8] = {
- .code = KEY_DOWN,
- .gpio = 109,
- .desc = "down sw",
- .active_low = 1,
- .debounce_interval = 30,
- },
-};
-
-static struct gpio_keys_platform_data ldp_gpio_keys = {
- .buttons = ldp_gpio_keys_buttons,
- .nbuttons = ARRAY_SIZE(ldp_gpio_keys_buttons),
- .rep = 1,
-};
-
-static struct platform_device ldp_gpio_keys_device = {
- .name = "gpio-keys",
- .id = -1,
- .dev = {
- .platform_data = &ldp_gpio_keys,
- },
-};
-
-static struct omap_smsc911x_platform_data smsc911x_cfg = {
- .cs = LDP_SMSC911X_CS,
- .gpio_irq = LDP_SMSC911X_GPIO,
- .gpio_reset = -EINVAL,
- .flags = SMSC911X_USE_32BIT,
-};
-
-static inline void __init ldp_init_smsc911x(void)
-{
- gpmc_smsc911x_init(&smsc911x_cfg);
-}
-
-/* LCD */
-
-#define LCD_PANEL_RESET_GPIO 55
-#define LCD_PANEL_QVGA_GPIO 56
-
-static const struct display_timing ldp_lcd_videomode = {
- .pixelclock = { 0, 5400000, 0 },
-
- .hactive = { 0, 240, 0 },
- .hfront_porch = { 0, 3, 0 },
- .hback_porch = { 0, 39, 0 },
- .hsync_len = { 0, 3, 0 },
-
- .vactive = { 0, 320, 0 },
- .vfront_porch = { 0, 2, 0 },
- .vback_porch = { 0, 7, 0 },
- .vsync_len = { 0, 1, 0 },
-
- .flags = DISPLAY_FLAGS_HSYNC_LOW | DISPLAY_FLAGS_VSYNC_LOW |
- DISPLAY_FLAGS_DE_HIGH | DISPLAY_FLAGS_PIXDATA_POSEDGE,
-};
-
-static struct panel_dpi_platform_data ldp_lcd_pdata = {
- .name = "lcd",
- .source = "dpi.0",
-
- .data_lines = 18,
-
- .display_timing = &ldp_lcd_videomode,
-
- .enable_gpio = -1, /* filled in code */
- .backlight_gpio = -1, /* filled in code */
-};
-
-static struct platform_device ldp_lcd_device = {
- .name = "panel-dpi",
- .id = 0,
- .dev.platform_data = &ldp_lcd_pdata,
-};
-
-static struct omap_dss_board_info ldp_dss_data = {
- .default_display_name = "lcd",
-};
-
-static void __init ldp_display_init(void)
-{
- int r;
-
- static struct gpio gpios[] __initdata = {
- {LCD_PANEL_RESET_GPIO, GPIOF_OUT_INIT_HIGH, "LCD RESET"},
- {LCD_PANEL_QVGA_GPIO, GPIOF_OUT_INIT_HIGH, "LCD QVGA"},
- };
-
- r = gpio_request_array(gpios, ARRAY_SIZE(gpios));
- if (r) {
- pr_err("Cannot request LCD GPIOs, error %d\n", r);
- return;
- }
-
- omap_display_init(&ldp_dss_data);
-}
-
-static int ldp_twl_gpio_setup(struct device *dev, unsigned gpio, unsigned ngpio)
-{
- int res;
-
- /* LCD enable GPIO */
- ldp_lcd_pdata.enable_gpio = gpio + 7;
-
- /* Backlight enable GPIO */
- ldp_lcd_pdata.backlight_gpio = gpio + 15;
-
- res = platform_device_register(&ldp_lcd_device);
- if (res)
- pr_err("Unable to register LCD: %d\n", res);
-
- return 0;
-}
-
-static struct twl4030_gpio_platform_data ldp_gpio_data = {
- .setup = ldp_twl_gpio_setup,
-};
-
-static struct regulator_consumer_supply ldp_vmmc1_supply[] = {
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
-static struct regulator_init_data ldp_vmmc1 = {
- .constraints = {
- .min_uV = 1850000,
- .max_uV = 3150000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(ldp_vmmc1_supply),
- .consumer_supplies = ldp_vmmc1_supply,
-};
-
-/* ads7846 on SPI */
-static struct regulator_consumer_supply ldp_vaux1_supplies[] = {
- REGULATOR_SUPPLY("vcc", "spi1.0"),
-};
-
-/* VAUX1 */
-static struct regulator_init_data ldp_vaux1 = {
- .constraints = {
- .min_uV = 3000000,
- .max_uV = 3000000,
- .apply_uV = true,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(ldp_vaux1_supplies),
- .consumer_supplies = ldp_vaux1_supplies,
-};
-
-static struct regulator_consumer_supply ldp_vpll2_supplies[] = {
- REGULATOR_SUPPLY("vdds_dsi", "omapdss"),
- REGULATOR_SUPPLY("vdds_dsi", "omapdss_dpi.0"),
- REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi.0"),
-};
-
-static struct regulator_init_data ldp_vpll2 = {
- .constraints = {
- .name = "VDVI",
- .min_uV = 1800000,
- .max_uV = 1800000,
- .apply_uV = true,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(ldp_vpll2_supplies),
- .consumer_supplies = ldp_vpll2_supplies,
-};
-
-static struct twl4030_platform_data ldp_twldata = {
- /* platform_data for children goes here */
- .vmmc1 = &ldp_vmmc1,
- .vaux1 = &ldp_vaux1,
- .vpll2 = &ldp_vpll2,
- .gpio = &ldp_gpio_data,
- .keypad = &ldp_kp_twl4030_data,
-};
-
-static int __init omap_i2c_init(void)
-{
- omap3_pmic_get_config(&ldp_twldata,
- TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC, 0);
- omap3_pmic_init("twl4030", &ldp_twldata);
- omap_register_i2c_bus(2, 400, NULL, 0);
- omap_register_i2c_bus(3, 400, NULL, 0);
- return 0;
-}
-
-static struct omap2_hsmmc_info mmc[] __initdata = {
- {
- .mmc = 1,
- .caps = MMC_CAP_4_BIT_DATA,
- .gpio_cd = -EINVAL,
- .gpio_wp = -EINVAL,
- },
- {} /* Terminator */
-};
-
-static struct platform_device *ldp_devices[] __initdata = {
- &ldp_gpio_keys_device,
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
- { .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-static struct mtd_partition ldp_nand_partitions[] = {
- /* All the partition sizes are listed in terms of NAND block size */
- {
- .name = "X-Loader-NAND",
- .offset = 0,
- .size = 4 * (64 * 2048), /* 512KB, 0x80000 */
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- },
- {
- .name = "U-Boot-NAND",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */
- .size = 10 * (64 * 2048), /* 1.25MB, 0x140000 */
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- },
- {
- .name = "Boot Env-NAND",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x1c0000 */
- .size = 2 * (64 * 2048), /* 256KB, 0x40000 */
- },
- {
- .name = "Kernel-NAND",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x0200000*/
- .size = 240 * (64 * 2048), /* 30M, 0x1E00000 */
- },
- {
- .name = "File System - NAND",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x2000000 */
- .size = MTDPART_SIZ_FULL, /* 96MB, 0x6000000 */
- },
-
-};
-
-static struct regulator_consumer_supply dummy_supplies[] = {
- REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
- REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
-};
-
-static void __init omap_ldp_init(void)
-{
- regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
- omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
- ldp_init_smsc911x();
- omap_i2c_init();
- platform_add_devices(ldp_devices, ARRAY_SIZE(ldp_devices));
- omap_ads7846_init(1, 54, 310, NULL);
- omap_serial_init();
- omap_sdrc_init(NULL, NULL);
- usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
- usb_musb_init(NULL);
- board_nand_init(ldp_nand_partitions, ARRAY_SIZE(ldp_nand_partitions),
- 0, 0, nand_default_timings);
-
- omap_hsmmc_init(mmc);
- ldp_display_init();
-}
-
-MACHINE_START(OMAP_LDP, "OMAP LDP board")
- .atag_offset = 0x100,
- .reserve = omap_reserve,
- .map_io = omap3_map_io,
- .init_early = omap3430_init_early,
- .init_irq = omap3_init_irq,
- .init_machine = omap_ldp_init,
- .init_late = omap3430_init_late,
- .init_time = omap_init_time,
- .restart = omap3xxx_restart,
-MACHINE_END
--
2.8.1
More information about the linux-arm-kernel
mailing list