[PATCH 09/11] phy: rockchip-emmc: Set phyctrl_frqsel based on card clock

Shawn Lin shawn.lin at rock-chips.com
Mon Jun 13 17:24:43 PDT 2016


在 2016/6/14 7:05, Doug Anderson 写道:
> Shawn,
>
> On Mon, Jun 13, 2016 at 1:54 AM, Shawn Lin <shawn.lin at rock-chips.com> wrote:
>> On 2016/6/8 6:44, Douglas Anderson wrote:
>>>
>>> The "phyctrl_frqsel" is described in the Arasan datasheet [1] as "the
>>> frequency range of DLL operation".  Although the Rockchip variant of
>>> this PHY has different ranges than the reference Arasan PHY it appears
>>> as if the functionality is similar.  We should set this phyctrl field
>>> properly.
>>>
>>> Note: as per Rockchip engineers, apparently the "phyctrl_frqsel" is
>>> actually only useful in HS200 / HS400 modes even though the DLL itself
>>> it used for some purposes in all modes.  See the discussion in the
>>> earlier change in this series: ("mmc: sdhci-of-arasan: Always power the
>>> PHY off/on when clock changes").  In any case, it shouldn't hurt to set
>>> this always.
>>>
>>> Note that this change should allow boards to run at HS200 / HS400 speed
>>> modes while running at 100 MHz or 150 MHz.  In fact, running HS400 at
>>> 150 MHz (giving 300 MB/s) is the main motivation of this series, since
>>> performance is still good but signal integrity problems are less
>>> prevelant at 150 MHz.
>>
>>
>> Thanks for doing this, but I think we should limit freq if assigning
>> max-frequency from DT more explicitly since the PHY could only support
>> 50/100/150/200M for hs200/400? Otherwise I can't say if the PHY could
>> always work well. i.e if geting 125000000 ... 174999999 , you code make
>> the phyctrl_frqsel to be 150M, so it will be 15% missing of precision
>> for tuning delay element. Ideally, the sample point should be in the
>> middle of window, but I don't know if there is a bad HW design makes
>> the window small enough which need special care about it.
>
> What would you suggest as a valid range, then?
>
>>From the public Arasan datasheet they seem to indicate +/- 15 MHz is
> sane.  Does that sound OK?  Presuming that all of your numbers
> (50/100/150/200) are centers, that means that we could support clock
> rates of:
>
> 35 MHz - 65 MHz
> 85 MHz - 115 MHz
> 135 MHz - 165 MHz
> 185 MHz - 200 MHz
>
>
> So how about if we add a warning for things that are outside of those
> ranges?  ...except no warning for < 35 MHz since presumably we're not
> using high speed modes when the DLL is that slow and so we're OK.

a warning should be ok.
If we ask 150M, but PLL only provide 175M maybe, then should we
fallback it to 150M or promote it to 200M when setting?

>
>
> NOTE: In rk3399 it's actually quite important to handle clocks that
> aren't exactly the right MHz.  When you ask for 150 MHz you actually
> end up a child of GPLL and actually end up at 148.5 MHz.  This should
> be close enough, but it's not exactly 150 MHz.  If we can't handle
> 148.5 MHz then the 150 MHz setting in the PHY is useless.
>
> Also note that on rk3399 we're fairly limited on the number of rates
> we can actually make since they need to be even divisors of 594 MHz or
> 800 MHz (assuming you don't rejigger all the PLLs in the SoC or
> something).  Most of the rates are actually in those ranges...

Yes I don't.

>
>
> -Doug
>
>
>


-- 
Best Regards
Shawn Lin




More information about the linux-arm-kernel mailing list