[RFC v4 4/7] extcon: usb-gpio: Add support for VBUS detection

[Roger Quadros]

On 09/06/16 11:43, Krzysztof Kozlowski wrote:
> On 06/09/2016 10:38 AM, Roger Quadros wrote:
>> Hi,
>>
>> On 08/06/16 16:48, Krzysztof Kozlowski wrote:
>>> Add VBUS pin detection support to extcon-usb-gpio driver for boards
>>> which have both VBUS and ID pins, or only one of them.
>>>
>>> The logic behind reporting USB and USB-HOST extcon cables is not
>>> affected. The driver however will report extcon changes for USB-VBUS and
>>> USB-ID.
>>>
>>> Signed-off-by: Robert Baldyga <r.baldyga at samsung.com>
>>> Signed-off-by: Krzysztof Kozlowski <k.kozlowski at samsung.com>
>>>
>>> ---
>>>
>>> Some parts base on old Robert's patchset.
>>> ---
>>>  drivers/extcon/extcon-usb-gpio.c | 125 +++++++++++++++++++++++++++++++--------
>>>  1 file changed, 99 insertions(+), 26 deletions(-)
>>>
>>> diff --git a/drivers/extcon/extcon-usb-gpio.c b/drivers/extcon/extcon-usb-gpio.c
>>> index a36aab007022..85b8a0ce5731 100644
>>> --- a/drivers/extcon/extcon-usb-gpio.c
>>> +++ b/drivers/extcon/extcon-usb-gpio.c
>>> @@ -35,7 +35,9 @@ struct usb_extcon_info {
>>>  	struct extcon_dev *edev;
>>>  
>>>  	struct gpio_desc *id_gpiod;
>>> +	struct gpio_desc *vbus_gpiod;
>>>  	int id_irq;
>>> +	int vbus_irq;
>>>  
>>>  	unsigned long debounce_jiffies;
>>>  	struct delayed_work wq_detcable;
>>> @@ -44,6 +46,8 @@ struct usb_extcon_info {
>>>  static const unsigned int usb_extcon_cable[] = {
>>>  	EXTCON_USB,
>>>  	EXTCON_USB_HOST,
>>> +	EXTCON_USB_ID,
>>> +	EXTCON_USB_VBUS,
>>>  	EXTCON_NONE,
>>>  };
>>>  
>>> @@ -55,7 +59,8 @@ static void usb_extcon_detect_cable(struct work_struct *work)
>>>  						    wq_detcable);
>>>  
>>>  	/* check ID and update cable state */
>>> -	id = gpiod_get_value_cansleep(info->id_gpiod);
>>> +	id = info->id_gpiod ? gpiod_get_value_cansleep(info->id_gpiod) : 1;
>>> +
>>>  	if (id) {
>>>  		/*
>>>  		 * ID = 1 means USB HOST cable detached.
>>> @@ -73,6 +78,14 @@ static void usb_extcon_detect_cable(struct work_struct *work)
>>>  		extcon_set_cable_state_(info->edev, EXTCON_USB, false);
>>>  		extcon_set_cable_state_(info->edev, EXTCON_USB_HOST, true);
>>>  	}
>>> +
>>> +	if (info->id_gpiod)
>>> +		extcon_set_cable_state_(info->edev, EXTCON_USB_ID, id);
>>> +	if (info->vbus_gpiod) {
>>> +		int vbus = gpiod_get_value_cansleep(info->vbus_gpiod);
>>> +
>>> +		extcon_set_cable_state_(info->edev, EXTCON_USB_VBUS, vbus);
>>> +	}
>>
>> What happens if either id_gpiod or vbus_gpiod is present?
>>
>> As per the DT binding document
>> "In general we have three cases:
>> 1. If VBUS and ID gpios are present we pass them as is
>> USB-HOST = !ID, USB = VBUS
>> 2. If only VBUS gpio is present we assume that ID pin is always High.
>> USB-HOST = false, USB = VBUS.
>> 3. If only ID pin is available we infer the VBUS pin states based on ID.
>> USB-HOST = !ID, USB = ID"
>>
>> So do you want to be consistent and infer VBUS and ID states based on the other?
> 
> Right, I couldn't make up my mind whether I want to change/improve
> existing logic or just add VBUS/ID raw notifying. Finally I left
> original code for USB/USB-HOST cables alone.
> 

I think it is better to stick to raw notifying so nothing needs to be changed.
If there is some mechanism to get the pin state and if the pin is not available
it should return error.

cheers,
-roger